Signal converter/disconnector, tension clamp connection weidmüller waz4 cvc dc 4-20/0-10v 8445050000 1 ks

Produkt Signal converter/disconnector, tension clamp connection weidmüller waz4 cvc dc 4-20/0-10v 8445050000 1 ks sme našli 50+x, pokiaľ to nie je to čo hľadáte, skúste frázu Signal converter/disconnector, tension clamp connection weidmüller waz4 cvc dc 4-20/0-10v 8445050000 1 ks upraviť a produkt hľadať znova.

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ4 CVC DC 4-20/0-10V 8445050000 1 ks

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ4 CVC DC 4-20/0-10V 8445050000 1 ks
Detail

The externally supplied ACT20M-CI-CO, MAS RPS/RPSH, MCZ CFC and WAS/WAZ 4/5 C signal converters/supply isolators can transmit, isolate and convert standardised DC current signals. They are optionally available in widths of 6 mm (ACT20M/MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (ACT20M, WAS/WAZ) or into a proportional frequency (MCZ CFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5) so that they can process signals quickly. The MAS/RPS/RPSH supply isolator can supply 2-wire sensors externally. They can also be used optionally to transmit the HART protocol (MAS RPSH). The 24 VDC supply voltage can be cross-connected on the module side via the CH20M BUS profile (ACT20M series) or using the ZQV4N (MAS/MCZ) or ZQV 2.5N (WAS/WAZ) pluggable jumpers. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. WAZ4 CVC DC 4-20/0-10 V (conrad.cz)

Podobné produkty ako Signal converter/disconnector, Tension clamp connection Weidmüller WAZ4 CVC DC 4-20/0-10V 8445050000 1 ks , Pelikan signal, pastelové barvy - balení 4 ks (7703064002692)

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ4 VVC DC 0-10/0-10V 8447140000 1 ks

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ4 VVC DC 0-10/0-10V 8447140000 1 ks
Detail

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ4 VVC DC 0-10/0-10 V (conrad.cz)

Podobné produkty ako Signal converter/disconnector, Tension clamp connection Weidmüller WAZ4 VVC DC 0-10/0-10V 8447140000 1 ks , Konektor dc 1 7 x 4 0 x 9 5mm kabel

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ5 VVC 0-10V/0-10V 8540340000 1 ks

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ5 VVC 0-10V/0-10V 8540340000 1 ks
Detail

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ5 VVC 0-10 V / 0-10 V (conrad.cz)

Podobné produkty ako Signal converter/disconnector, Tension clamp connection Weidmüller WAZ5 VVC 0-10V/0-10V 8540340000 1 ks , Dc superhrdinky 1 zkouškové peklo (978-80-7449-637-0)

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ5 VCC 0-10V/4-20MA 8540300000 1 ks

Signal converter/disconnector, Tension clamp connection Weidmüller WAZ5 VCC 0-10V/4-20MA 8540300000 1 ks
Detail

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ5 VCC 0-10 V / 4-20MA (conrad.cz)

Podobné produkty ako Signal converter/disconnector, Tension clamp connection Weidmüller WAZ5 VCC 0-10V/4-20MA 8540300000 1 ks , Oxford blinkr led signal 1 (m010-045)

Signal converter/disconnector, Screw connection Weidmüller WAS4 CCC DC 4-20/0-20MA 8445010000 1 ks

Signal converter/disconnector, Screw connection Weidmüller WAS4 CCC DC 4-20/0-20MA 8445010000 1 ks
Detail

The externally supplied ACT20M-CI-CO, MAS RPS/RPSH, MCZ CFC and WAS/WAZ 4/5 C signal converters/supply isolators can transmit, isolate and convert standardised DC current signals. They are optionally available in widths of 6 mm (ACT20M/MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (ACT20M, WAS/WAZ) or into a proportional frequency (MCZ CFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5) so that they can process signals quickly. The MAS/RPS/RPSH supply isolator can supply 2-wire sensors externally. They can also be used optionally to transmit the HART protocol (MAS RPSH). The 24 VDC supply voltage can be cross-connected on the module side via the CH20M BUS profile (ACT20M series) or using the ZQV4N (MAS/MCZ) or ZQV 2.5N (WAS/WAZ) pluggable jumpers. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Co4 CCC DC 4-20 / 0-20MA (conrad.cz)

Podobné produkty ako Signal converter/disconnector, Screw connection Weidmüller WAS4 CCC DC 4-20/0-20MA 8445010000 1 ks , Godin nylon hard tension (hn161508)

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/4 V 0-10V 8432250000 1 ks

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/4 V 0-10V 8432250000 1 ks
Detail

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 V 0-10 V (conrad.cz)

Podobné produkty ako RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/4 V 0-10V 8432250000 1 ks , Leatherman signal 37447571190

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/2 V 0-10V 8432190000 1 ks

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/2 V 0-10V 8432190000 1 ks
Detail

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 V 0-10 V (conrad.cz)

Podobné produkty ako RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/2 V 0-10V 8432190000 1 ks , Hornsby bruce: non-secure connection - lp (zappo0021)

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/3 V 0-10V 8432130000 1 ks

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/3 V 0-10V 8432130000 1 ks
Detail

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 V 0-10 V (conrad.cz)

Podobné produkty ako RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/3 V 0-10V 8432130000 1 ks , Martin classical premium magnifico normal tension (hn192041)

WAVESERIES, Limit value monitoring, 0(4)...20 mA, 1, 3 A, 2, Tension clamp connection Weidmüller WAZ5 DC/ALARM 8543880000 1 ks

WAVESERIES, Limit value monitoring, 0(4)...20 mA, 1, 3 A, 2, Tension clamp connection Weidmüller WAZ5 DC/ALARM 8543880000 1 ks
Detail

WAS/WAZ5 DC/Alarm analogue DC current/voltage signal converters with integrated limit-value monitoring and external power supply. The input and output parameters can be configured. During operation, the analogue value on the input side is continuously monitored. The upper and lower operating points can be adjusted and are switched via relays. Various monitoring functions such as fail-safe, non fail-safe, high-/low trip and hysteresis can be adjusted via DIP switches. The WAS/WAZ5 DC/Alarm is constructed with 3-way isolation. Either screw or tension-clamp wire connections are available for the monitoring modules. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N cross-connectors on the module side. The 17.5 mm wide monitoring components can be used anywhere within the electrical cabinet or in process and industrial automation applications. WAZ5 DC/alarm (conrad.cz)

Podobné produkty ako WAVESERIES, Limit value monitoring, 0(4)...20 mA, 1, 3 A, 2, Tension clamp connection Weidmüller WAZ5 DC/ALARM 8543880000 1 ks , Bose bass module connection cable (851220-0010)

Passive isolator, Tension clamp connection Weidmüller WAZ5 CCC LP 0-20/0-20MA 8444960000 1 ks

Passive isolator, Tension clamp connection Weidmüller WAZ5 CCC LP 0-20/0-20MA 8444960000 1 ks
Detail

The ACT20M-CI-CO-ILP, MCZ CCC and WAS5 CCC LP are 1/2-channel passive isolators that are supplied via the input loop current. They are optionally available in 6 mm (ACT20M/ MCZ series) or 17.5 mm (WAS5 CCC LP) housings. The input and output circuits are completely, electrically isolated from each other. The passive isolators are designed with 1 or 2 channels. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Passive isolators are used to electrically isolate normalised signals (from 0/4 to 20 mA).The modules get their power supply from the current loop on the input side. The power for signal transmission and supply comes from the active 0/4–20 mA signal. They have very low current consumption and can be used anywhere in the field where no suitable power supply is available. These devices are used in a variety of application processes as signal isolators and signal multipliers. They can be used to eliminate measurement errors caused by differences in earth potentials. WAZ5 CCC LP 0-20 / 0-20mA (conrad.cz)

Podobné produkty ako Passive isolator, Tension clamp connection Weidmüller WAZ5 CCC LP 0-20/0-20MA 8444960000 1 ks , Martin classical normal tension ball end (hn145376)

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/4 C 0/4-20MA 8432280000 1 ks

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/4 C 0/4-20MA 8432280000 1 ks
Detail

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 C 0/4 až 20 mA (conrad.cz)

Podobné produkty ako RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/4 C 0/4-20MA 8432280000 1 ks , Rigid 20 stanový kolík kovový 1 ks (62661)

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/3 C 0/4-20MA 8432160000 1 ks

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/3 C 0/4-20MA 8432160000 1 ks
Detail

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 C 0/4 až 20 mA (conrad.cz)

Podobné produkty ako RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/3 C 0/4-20MA 8432160000 1 ks , Znovuzrození hrdinů dc (978-80-7449-611-0)

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/2 C 0/4-20MA 8432220000 1 ks

RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/2 C 0/4-20MA 8432220000 1 ks
Detail

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 C 0/4 až 20 mA (conrad.cz)

Podobné produkty ako RTD transformer, Tension clamp connection Weidmüller WTZ4 PT100/2 C 0/4-20MA 8432220000 1 ks , Hobot prodlužovací dc kabel 4 m (hb16814)

ACT20M, Signal converter/disconnector, Screw connection Weidmüller ACT20M-CI-CO-OLP-S 1176040000 1 ks

ACT20M, Signal converter/disconnector, Screw connection Weidmüller ACT20M-CI-CO-OLP-S 1176040000 1 ks
Detail

The ACT20M-CI-CO-OLP, WAS/WAZ5 OLP signal isolator/splitter (2-wire system) is supplied via the output current loop and has an analogue DC current input. The 1- and 2-channel signal isolators are supplied from the current loop. They are available in the 6.1 mm (ACT20M series) or 17.5 mm (WAVESERIES) housings. The input and output circuits are electrically isolated from each other. The power is supplied via the 4–20 mA current loop on the output side. The devices come optionally in a splitter version with two loop-fed outputs. The devices can be mounted on a DIN rail and consume minimal power. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Signal converters with output-loop power supplies are used in a variety of application processes as signal isolators and signal multipliers (splitters) and signal amplifiers. They can be used to eliminate measurement errors caused by differences in earth potentials. ACT20M-CI-CO-OLP-S (conrad.cz)

Podobné produkty ako ACT20M, Signal converter/disconnector, Screw connection Weidmüller ACT20M-CI-CO-OLP-S 1176040000 1 ks , Altom korková podložka pod hrnec 20 x 20 cm, sada 4 ks

ACT20M, Signal converter/disconnector, Screw connection Weidmüller ACT20M-2CI-2CO-OLP-S 1176050000 1 ks

ACT20M, Signal converter/disconnector, Screw connection Weidmüller ACT20M-2CI-2CO-OLP-S 1176050000 1 ks
Detail

The ACT20M-CI-CO-OLP, WAS/WAZ5 OLP signal isolator/splitter (2-wire system) is supplied via the output current loop and has an analogue DC current input. The 1- and 2-channel signal isolators are supplied from the current loop. They are available in the 6.1 mm (ACT20M series) or 17.5 mm (WAVESERIES) housings. The input and output circuits are electrically isolated from each other. The power is supplied via the 4–20 mA current loop on the output side. The devices come optionally in a splitter version with two loop-fed outputs. The devices can be mounted on a DIN rail and consume minimal power. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Signal converters with output-loop power supplies are used in a variety of application processes as signal isolators and signal multipliers (splitters) and signal amplifiers. They can be used to eliminate measurement errors caused by differences in earth potentials. ACT20M-2CI 2CO-OLP-S (conrad.cz)

Podobné produkty ako ACT20M, Signal converter/disconnector, Screw connection Weidmüller ACT20M-2CI-2CO-OLP-S 1176050000 1 ks , Spona power clamp w1, 36 - 39 mm, 20 mm (y147085)

Signal converter/disconnector, Limit value monitoring, Screw connection Weidmüller WAS6 TTA EX 8964310000 1 ks

Signal converter/disconnector, Limit value monitoring, Screw connection Weidmüller WAS6 TTA EX 8964310000 1 ks
Detail

WAS/WAZ6 TTA is a universal signal converter and trip amplifier that can be configured on the PC. Combines the functions of isolation, transmission, linearisation and trip amplification in a single module. These exceptional characteristics and outstanding configurability combine to make the TTA truly unique. The TTA functions with stability and precision under a wide range of voltages and ambient temperatures. It is compatible with all standard sensor types. Universal input signals: temperature signals such as resistance thermometer, thermocouple, potentiometer, frequency transmitter, DC voltage signals and current signals Loop-powered or passive input Wide-range power supply: 18 – 264 V AC/DC User-defined linearization Inputs and outputs can be configured on PC Combined analogue and relay output Ambient temperature range: -40 °C …70 °C The CBX200 USB interface is used to connect to the PC. The WAS/WAZ6 TTA is also offered as an option with ATEX Zone 2 and UL C1D2 approvals. Co6 TTA EX (conrad.cz)

Podobné produkty ako Signal converter/disconnector, Limit value monitoring, Screw connection Weidmüller WAS6 TTA EX 8964310000 1 ks , Pelikan signal růžový (60078808)

Universal signal converters / trip amplifiers, Tension clamp connection Weidmüller WAZ6 TTA EX 8964320000 1 ks

Universal signal converters / trip amplifiers, Tension clamp connection Weidmüller WAZ6 TTA EX 8964320000 1 ks
Detail

WAS/WAZ6 TTA is a universal signal converter and trip amplifier that can be configured on the PC. Combines the functions of isolation, transmission, linearisation and trip amplification in a single module. These exceptional characteristics and outstanding configurability combine to make the TTA truly unique. The TTA functions with stability and precision under a wide range of voltages and ambient temperatures. It is compatible with all standard sensor types. Universal input signals: temperature signals such as resistance thermometer, thermocouple, potentiometer, frequency transmitter, DC voltage signals and current signals Loop-powered or passive input Wide-range power supply: 18 – 264 V AC/DC User-defined linearization Inputs and outputs can be configured on PC Combined analogue and relay output Ambient temperature range: -40 °C …70 °C The CBX200 USB interface is used to connect to the PC. The WAS/WAZ6 TTA is also offered as an option with ATEX Zone 2 and UL C1D2 approvals. WAZ6 TTA EX (conrad.cz)

Podobné produkty ako Universal signal converters / trip amplifiers, Tension clamp connection Weidmüller WAZ6 TTA EX 8964320000 1 ks , Pelikan signal ledový (60078812)

MICROSERIES, Signal converter/disconnector, , Weidmüller MAZ DC/DC SELECT 8594840000 1 ks

MICROSERIES, Signal converter/disconnector, , Weidmüller MAZ DC/DC SELECT 8594840000 1 ks
Detail

The configurable MAS/MAZ DC/DC select and MAS DC/DC select HI: DC signal isolating converters with external power supply in 6.1 mm width, for transmitting and isolating standardised analogue DC current and voltage signals. The input and output parameters can be configured as required using DIP switches. The isolating transformers are designed with 0.5 kV or 2.5 kV (DC/DC select HI) of complete electrical isolation. The 24 V DC voltage supply can be bridged module by module using the ZQV 4N plug-in cross-connectors. The MI 8 A-I/O S-SUBD15Binterface module makes it easy to carry out byte-wise system wiring with pre-assembled cables on the inputs or outputs. They can be used in many applications around the world because of their international approvals (cULus, C1D2 and ATEX Zone2). MAZ DC/DC select (conrad.cz)

Podobné produkty ako MICROSERIES, Signal converter/disconnector, , Weidmüller MAZ DC/DC SELECT 8594840000 1 ks , Pelikan signal korálový (60078810)

WAVESERIES, Voltage monitoring, 1, 1, Tension clamp connection Weidmüller WAZ2 VMA V AC 8581230000 1 ks

WAVESERIES, Voltage monitoring, 1, 1, Tension clamp connection Weidmüller WAZ2 VMA V AC 8581230000 1 ks
Detail

The WAS/WAZ2 VMA V ac: single-phase AC voltage monitoring components with analogue output and external power supply. On the input side, these components provide voltages in the ranges 0 to 30/70/130/260 and 450 VAC for measuring. A standardised DC current/voltage signal is available on the output side. The devices use the true RMS method and are capable of measuring voltages in the frequency range from 40 to 400 Hz with an accuracy of 1 to 2%. The input/output and supply are securely isolated with 4 kV. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N jumpers on the module side. WAZ2 VMA V ac (conrad.cz)

Podobné produkty ako WAVESERIES, Voltage monitoring, 1, 1, Tension clamp connection Weidmüller WAZ2 VMA V AC 8581230000 1 ks , Axagon pcem2-dc (pcem2-dc)

WAVESERIES, Current monitoring, 0...1 A AC/ 0...5 A AC/ 0...10 A AC, 1, 1, Tension clamp connection Weidmüller WAZ1 CMA LP 1/5/10A AC 8528660000 1 ks

WAVESERIES, Current monitoring, 0...1 A AC/ 0...5 A AC/ 0...10 A AC, 1, 1, Tension clamp connection Weidmüller WAZ1 CMA LP 1/5/10A AC 8528660000 1 ks
Detail

Output current loop fed AC current monitoring components WAS/WAZ1 CMA LP. They can measure single-phase 50/60 Hz AC currents of up to 10 A using the Root Mean Square (RMS) method on the input side. They can also be switched between three ranges. No external power supply is used; the supply is only via the 4...20 mA current loop on the output side. The input and output circuits are securely isolated with 4 kV. The monitoring components come in a 17.5-mm-wide WAVEBOX housing. These devices can be used in many process automation applications because they are not dependent on an external power supply. International approvals (such as ATEX Zone 2 and UL C1D2) also permit usage in explosion-risk zones. WAZ1 CMA LP 1/5/10 A ac (conrad.cz)

Podobné produkty ako WAVESERIES, Current monitoring, 0...1 A AC/ 0...5 A AC/ 0...10 A AC, 1, 1, Tension clamp connection Weidmüller WAZ1 CMA LP 1/5/10A AC 8528660000 1 ks , 4home panáky skull hot&cool, 20 ml, 4 ks

T-LED DimLED přijímač 0/1-10V 4-kanálový 069333

Detail

DimLED přijímač slouží jako hlavní řídící jednotka, která řídí signálem 0/1-10V DimLED stmívač 065503. viz obrázky nebo návod. Na tento přijímač lze tedy připojit až 4 jednotky 065503 a ovládat je dohromady jedním ovladačem. Pro ovládání více okruhů je nutno použít jeden přijímač na každý okruh. Na každý přijímač lze napárovat až 10 různých ovladačů řady dimLED a tak ovládat z několika míst. V případě přerušení a poté opětovného připojení napájení (například přerušením napájení zdroje) má tento přijímač paměť nastavení intenzity (intenzita osvětlení se vrátí na naposled nastavenou). Doporučujeme přijímač, instalovat v min. 30-50 cm vzdálenosti od zdroje rušení, tedy např.: (kovových konstrukcí, napětí 230 V, transformátorů, LED driverů, AL profilů atd.), Pokud je to možné, tak přijímač natočit textem směrem k ovladači. Přijímač má anténu, pod textem. (eshop.ledsolution.cz)

Podobné produkty ako T-LED DimLED přijímač 0/1-10V 4-kanálový 069333 , Ezpets2u tension ring puller pro psy červený (chphr0761)

Interface, RS VERT, 4 P, Tension clamp connection RS VERT 4P 20X4 Z Weidmüller Množství: 1 ks

Interface, RS VERT, 4 P, Tension clamp connection RS VERT 4P 20X4 Z Weidmüller Množství: 1 ks
Detail

Distributor module with 4 voltage potentials (P1,P2,P3,P4) in 20P1,20P2,20P3and 20P4 for tension-clamp or screw connection. RS VERTIKÁLNÍ 4P 20X4 Z (conrad.cz)

Podobné produkty ako Interface, RS VERT, 4 P, Tension clamp connection RS VERT 4P 20X4 Z Weidmüller Množství: 1 ks , Ezpets2u tension ring puller pro psy oranžový (chphr0759)

1-wire, Tension clamp connection FTA-C300-32DIOHV-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-32DIOHV-Z Weidmüller Množství: 1 ks
Detail

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DIOHV-Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-32DIOHV-Z Weidmüller Množství: 1 ks , Ezpets2u tension ring puller pro psy zelený (chphr0760)

2-wire, Tension clamp connection RS F40 INIT32 LMZF Weidmüller Množství: 1 ks

2-wire, Tension clamp connection RS F40 INIT32 LMZF Weidmüller Množství: 1 ks
Detail

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT 32 LMZF (conrad.cz)

Podobné produkty ako 2-wire, Tension clamp connection RS F40 INIT32 LMZF Weidmüller Množství: 1 ks , Průvodce českými dějinami 20. století (978-80-905081-0-1)

1-wire, Tension clamp connection FTA-C300-32DO-RSLIM-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-32DO-RSLIM-Z Weidmüller Množství: 1 ks
Detail

Insulated FTAs for Honeywell C300 IOTA digital input/output. Insulated interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. High current switching capacity in a compact design Possibility of feeding the IOTA from the FTA (fuse protected) Screw or tension clamp connection FTA-C300 32 DO-RSLIM-Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-32DO-RSLIM-Z Weidmüller Množství: 1 ks , Panasonic lumix dc-s5 + lumix s 20-60 mm f/3,5-5,6 macro o.i.s. (dc-s5ke-k)

1-wire, Tension clamp connection FTA-C300-32DO-LD-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-32DO-LD-Z Weidmüller Množství: 1 ks
Detail

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-LD-Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-32DO-LD-Z Weidmüller Množství: 1 ks , Vánoční dekorační ozdoba, 20 cm, zlatá, 1 ks (83501271)

1-wire, Tension clamp connection FTA-C300-16AO-SH-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-16AO-SH-Z Weidmüller Množství: 1 ks
Detail

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-SH-Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-16AO-SH-Z Weidmüller Množství: 1 ks , Fnx barber kamencové zápalky 1 bal. / 20 ks (8691988003699)

1-wire, Tension clamp connection FTA-C300-16AO-TEST-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-16AO-TEST-Z Weidmüller Množství: 1 ks
Detail

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-TEST Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-16AO-TEST-Z Weidmüller Množství: 1 ks , Gardena 2-cestný ventil 3/4" + 1" (0940-20)

1-wire, Tension clamp connection FTA-C300-32DI-LD-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-32DI-LD-Z Weidmüller Množství: 1 ks
Detail

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DI-LD-Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-32DI-LD-Z Weidmüller Množství: 1 ks , Písanky 1-6 (859-4-315-0586-0)

1-wire, Tension clamp connection FTA-C300-32DO-FUSE-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-32DO-FUSE-Z Weidmüller Množství: 1 ks
Detail

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-FUSE-Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-32DO-FUSE-Z Weidmüller Množství: 1 ks , Dc comics - batman - art scale 1/10 (609963127900)

1-wire, Tension clamp connection FTA-C300-16AI-SH-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-16AI-SH-Z Weidmüller Množství: 1 ks
Detail

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI-SH-Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-16AI-SH-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-16AI-TEST-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection FTA-C300-16AI-TEST-Z Weidmüller Množství: 1 ks
Detail

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI TESTOVACÍ Z (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection FTA-C300-16AI-TEST-Z Weidmüller Množství: 1 ks

1-wire, Tension clamp connection RS F10 I/O8 LMZF Weidmüller Množství: 1 ks

1-wire, Tension clamp connection RS F10 I/O8 LMZF Weidmüller Množství: 1 ks
Detail

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 I/O8 LMZF (conrad.cz)

Podobné produkty ako 1-wire, Tension clamp connection RS F10 I/O8 LMZF Weidmüller Množství: 1 ks

ACT20X, Signal converter/disconnector, Weidmüller ACT20X-CJC-HTI-S PRT 21 1160650000 1 ks

ACT20X, Signal converter/disconnector, Weidmüller ACT20X-CJC-HTI-S PRT 21 1160650000 1 ks
Detail

Connection terminals for the ACT20X thermal modules for external cold-junction compensation ACT20X-CJC HTI-S PRT 21 (conrad.cz)

Podobné produkty ako ACT20X, Signal converter/disconnector, Weidmüller ACT20X-CJC-HTI-S PRT 21 1160650000 1 ks

ACT20X, Signal converter/disconnector, Weidmüller ACT20X-CJC-HTI-S PRT 11 1160640000 1 ks

ACT20X, Signal converter/disconnector, Weidmüller ACT20X-CJC-HTI-S PRT 11 1160640000 1 ks
Detail

Connection terminals for the ACT20X thermal modules for external cold-junction compensation ACT20X-CJC HTI-S PRT 11 (conrad.cz)

Podobné produkty ako ACT20X, Signal converter/disconnector, Weidmüller ACT20X-CJC-HTI-S PRT 11 1160640000 1 ks

3-wire, Tension clamp connection RS F10 INIT8 LD LMZF Weidmüller Množství: 1 ks

3-wire, Tension clamp connection RS F10 INIT8 LD LMZF Weidmüller Množství: 1 ks
Detail

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 INIT8 LD LMZF (conrad.cz)

Podobné produkty ako 3-wire, Tension clamp connection RS F10 INIT8 LD LMZF Weidmüller Množství: 1 ks

3-wire, Tension clamp connection RS F40 INIT32 LD LMZF Weidmüller Množství: 1 ks

3-wire, Tension clamp connection RS F40 INIT32 LD LMZF Weidmüller Množství: 1 ks
Detail

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT32 LD LMZF (conrad.cz)

Podobné produkty ako 3-wire, Tension clamp connection RS F40 INIT32 LD LMZF Weidmüller Množství: 1 ks

Interface, RSM, 16 2CO, RCL, Tension clamp connection RSM-16 2CO Z Weidmüller Množství: 1 ks

Interface, RSM, 16 2CO, RCL, Tension clamp connection RSM-16 2CO Z Weidmüller Množství: 1 ks
Detail

Digital output interface per-relay for electrical signal transmission between the PLC and the field. Electrical isolation by pluggable relays. Integrated LED status display. Screw or tension clamp-connection. Additional functions: in-series fuse or isolator 2 versions available: compact (RSS relay) or standard (RCL relay). RSM-16 2CO Z (conrad.cz)

Podobné produkty ako Interface, RSM, 16 2CO, RCL, Tension clamp connection RSM-16 2CO Z Weidmüller Množství: 1 ks

Interface, RSF, Plug-in connector acc. IEC 603-1 / DIN 41651, 20-pole, Tension clamp connection RS F20 Z Weidmüller Množství: 1 ks

Interface, RSF, Plug-in connector acc. IEC 603-1 / DIN 41651, 20-pole, Tension clamp connection RS F20 Z Weidmüller Množství: 1 ks
Detail

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F20 Z (conrad.cz)

Podobné produkty ako Interface, RSF, Plug-in connector acc. IEC 603-1 / DIN 41651, 20-pole, Tension clamp connection RS F20 Z Weidmüller Množství: 1 ks

Interface, RS VERT, 6 P, Tension clamp connection RS VERT 6P 12X6 Z Weidmüller Množství: 1 ks

Interface, RS VERT, 6 P, Tension clamp connection RS VERT 6P 12X6 Z Weidmüller Množství: 1 ks
Detail

Distributor module with 6 voltage potentials (P1,P2,P3,P4,P5,P6) in 12P1,12P2,12P3 ,12P4,12P5 and 12P6 for tension-clamp or screw connection. RS VERTIKÁLNÍ 6P 12X6 Z (conrad.cz)

Podobné produkty ako Interface, RS VERT, 6 P, Tension clamp connection RS VERT 6P 12X6 Z Weidmüller Množství: 1 ks

Interface, RS, LED, 3-wire, Tension clamp connection RS16ES-T-L H/Z Weidmüller Množství: 1 ks

Interface, RS, LED, 3-wire, Tension clamp connection RS16ES-T-L H/Z Weidmüller Množství: 1 ks
Detail

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS16ES-T-L H/Z (conrad.cz)

Podobné produkty ako Interface, RS, LED, 3-wire, Tension clamp connection RS16ES-T-L H/Z Weidmüller Množství: 1 ks

Interface, RSM, 8 compact, RCL, Tension clamp connection RSM-8 C 1CO Z Weidmüller Množství: 1 ks

Interface, RSM, 8 compact, RCL, Tension clamp connection RSM-8 C 1CO Z Weidmüller Množství: 1 ks
Detail

Digital output interface per-relay for electrical signal transmission between the PLC and the field. Electrical isolation by pluggable relays. Integrated LED status display. Screw or tension clamp-connection. Additional functions: in-series fuse or isolator 2 versions available: compact (RSS relay) or standard (RCL relay). RSM-8 C 1CO Z (conrad.cz)

Podobné produkty ako Interface, RSM, 8 compact, RCL, Tension clamp connection RSM-8 C 1CO Z Weidmüller Množství: 1 ks

Interface, RS, LED, 1-wire, Tension clamp connection RS 32IO 1W L H Z Weidmüller Množství: 1 ks

Interface, RS, LED, 1-wire, Tension clamp connection RS 32IO 1W L H Z Weidmüller Množství: 1 ks
Detail

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 1W L H Z (conrad.cz)

Podobné produkty ako Interface, RS, LED, 1-wire, Tension clamp connection RS 32IO 1W L H Z Weidmüller Množství: 1 ks

Interface, RS, LED, 3-wire, Tension clamp connection RS 32IO 3W L H Z Weidmüller Množství: 1 ks

Interface, RS, LED, 3-wire, Tension clamp connection RS 32IO 3W L H Z Weidmüller Množství: 1 ks
Detail

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 3W L H Z (conrad.cz)

Podobné produkty ako Interface, RS, LED, 3-wire, Tension clamp connection RS 32IO 3W L H Z Weidmüller Množství: 1 ks

Interface, RS, LED, 2-wire, Tension clamp connection RS 32IO 2W L H Z Weidmüller Množství: 1 ks

Interface, RS, LED, 2-wire, Tension clamp connection RS 32IO 2W L H Z Weidmüller Množství: 1 ks
Detail

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W L H Z (conrad.cz)

Podobné produkty ako Interface, RS, LED, 2-wire, Tension clamp connection RS 32IO 2W L H Z Weidmüller Množství: 1 ks

T-LED DimLED bezdrátový nástěnný ovladač 0/1-10V 4-kanálový Vyberte barvu: Černá 069251

Detail

Čtyřkanálový LED ovladač pro jednobarevné osvětlení je bezdrátový radiofrekvenční ovládací systém, jednoho ovladače a několik přijímačů. S jedním ovladačem lze ovládat nezávisle 4 zóny, která se může skládat z několika přijímačů. Tyto přijímače se po sehrání na jednotlivé předvolbě na ovladači ovládají jako jedna sekce. Ovladač také umožňuje ovládat až 4 zařízení se signálem 0-10V, případně 1-10V. Přijímač může být ukrytý (za zdí, sádrokartónem či ve skříni), není nutná přímá viditelnost přijímače pro ovladač. Ovládání probíhá na dotykové lince uprostřed ovladače. Vlastnosti a výhody systému dimLED: Stmívání je stabilní a spolehlivé, dosah ovladače ≤ 30M. Stmívání v rozmezí 0-100%, stmívání měkké, bez blikání. Při zapnutí dojde k pozvolnému rozsvícení, při vypnutí dojde k pozvolnému setmění. Ovládání: Ovládání probíhá na dotykové lince uprostřed ovladače. Dotykem na lince dochází k nastavování intenzity. Tlačítka na krajích ovladače slouží k dalším možnostem ovládání a vybírání zón. (eshop.ledsolution.cz)

Podobné produkty ako T-LED DimLED bezdrátový nástěnný ovladač 0/1-10V 4-kanálový Vyberte barvu: Černá 069251

T-LED DimLED bezdrátový nástěnný ovladač 0/1-10V 4-kanálový Vyberte barvu: Bílá 069250

Detail

Čtyřkanálový LED ovladač pro jednobarevné osvětlení je bezdrátový radiofrekvenční ovládací systém, jednoho ovladače a několik přijímačů. S jedním ovladačem lze ovládat nezávisle 4 zóny, která se může skládat z několika přijímačů. Tyto přijímače se po sehrání na jednotlivé předvolbě na ovladači ovládají jako jedna sekce. Ovladač také umožňuje ovládat až 4 zařízení se signálem 0-10V, případně 1-10V. Přijímač může být ukrytý (za zdí, sádrokartónem či ve skříni), není nutná přímá viditelnost přijímače pro ovladač. Ovládání probíhá na dotykové lince uprostřed ovladače. Vlastnosti a výhody systému dimLED: Stmívání je stabilní a spolehlivé, dosah ovladače ≤ 30M. Stmívání v rozmezí 0-100%, stmívání měkké, bez blikání. Při zapnutí dojde k pozvolnému rozsvícení, při vypnutí dojde k pozvolnému setmění. Ovládání: Ovládání probíhá na dotykové lince uprostřed ovladače. Dotykem na lince dochází k nastavování intenzity. Tlačítka na krajích ovladače slouží k dalším možnostem ovládání a vybírání zón. (eshop.ledsolution.cz)

Podobné produkty ako T-LED DimLED bezdrátový nástěnný ovladač 0/1-10V 4-kanálový Vyberte barvu: Bílá 069250

Interface, RSF PLC, LED, 2-wire, Tension clamp connection RSF PLC 2W 32IO LEDS Z Weidmüller Množství: 1 ks

Interface, RSF PLC, LED, 2-wire, Tension clamp connection RSF PLC 2W 32IO LEDS Z Weidmüller Množství: 1 ks
Detail

Compact interfaces for transmitting 32 digital input/output signals (RSF SPS). Signals optionally with byte grouping (can be set using jumper). Can be switched between positive or negative signal (set with jumper) An optional LED status display shows the status and the operating voltages. Each circuit can be protected by 5x20 mm individual fuses. Available with tension-clamp or screw connection. RSF PLC 2W 32 IO LED Z (conrad.cz)

Podobné produkty ako Interface, RSF PLC, LED, 2-wire, Tension clamp connection RSF PLC 2W 32IO LEDS Z Weidmüller Množství: 1 ks

Interface, RS, Isolator, 2-wire, Tension clamp connection RS 8AIO I-M-DP SD Z Weidmüller Množství: 1 ks

Interface, RS, Isolator, 2-wire, Tension clamp connection RS 8AIO I-M-DP SD Z Weidmüller Množství: 1 ks
Detail

The analogue interfaces are equipped with SubD connectors. Thus they offer sufficient shielding for analogue signal transmission. They are also equipped with very useful isolators and test sockets for measuring voltage or current. RS 8 AIO I-M-DP SD Z (conrad.cz)

Podobné produkty ako Interface, RS, Isolator, 2-wire, Tension clamp connection RS 8AIO I-M-DP SD Z Weidmüller Množství: 1 ks

DC/DC měnič napětí do auta Hama Converter 1000 /1 A

Detail

Nastavitelné výstupní napětí·Možnost obrácení polarity·Vč. 8 DC adaptér Máte univerzální napájecí zdroj pro notebooky značky Hama, ale vhodný adaptér pro váš notebook byl nejsou součástí dodávky? Pro většinu běžných modelů etablierter značek jsou k dispozici adaptér, doporučujeme elegantním vás tato během několika dní na.de/adaptér servisní zdarma ke! kostenlos zu! DC/DC měniče · 8 adaptérů · . (conrad.cz)

Podobné produkty ako DC/DC měnič napětí do auta Hama Converter 1000 /1 A
PELIKAN SIGNAL, pastelové barvy - balení 4 ks (7703064002692), konektor dc 1 7 x 4 0 x 9 5mm kabel, DC Superhrdinky 1 Zkouškové peklo (978-80-7449-637-0), OXFORD blinkr LED Signal 1 (M010-045), GODIN Nylon Hard Tension (HN161508), leatherman signal 37447571190, Hornsby Bruce: Non-Secure Connection - LP (ZAPPO0021), MARTIN Classical Premium Magnifico Normal Tension (HN192041), BOSE Bass Module Connection Cable (851220-0010), MARTIN Classical Normal Tension Ball End (HN145376), Rigid 20 stanový kolík kovový 1 ks (62661), Znovuzrození hrdinů DC (978-80-7449-611-0), HOBOT prodlužovací DC kabel 4 m (HB16814), Altom Korková podložka pod hrnec 20 x 20 cm, sada 4 ks, Spona Power Clamp W1, 36 - 39 mm, 20 mm (Y147085), PELIKAN Signal růžový (60078808), PELIKAN Signal ledový (60078812), PELIKAN Signal korálový (60078810), AXAGON PCEM2-DC (PCEM2-DC), 4Home Panáky Skull Hot&Cool, 20 ml, 4 ks, EzPets2U Tension ring Puller pro psy červený (CHPhr0761), EzPets2U Tension ring Puller pro psy oranžový (CHPhr0759), EzPets2U Tension ring Puller pro psy zelený (CHPhr0760), Průvodce českými dějinami 20. století (978-80-905081-0-1), Panasonic Lumix DC-S5 + Lumix S 20-60 mm f/3,5-5,6 Macro O.I.S. (DC-S5KE-K), Vánoční dekorační ozdoba, 20 cm, zlatá, 1 ks (83501271), FNX Barber Kamencové zápalky 1 bal. / 20 ks (8691988003699), Gardena 2-cestný ventil 3/4" + 1" (0940-20), Písanky 1-6 (859-4-315-0586-0), DC Comics - Batman - Art Scale 1/10 (609963127900)