Interface, rs, isolator, 2-wire, tension clamp connection rs 8aio i-m-dp sd z weidmüller množství: 1 ks

The analogue interfaces are equipped with SubD connectors. Thus they offer sufficient shielding for analogue signal transmission. They are also equipped with very useful isolators and test sockets for measuring voltage or current. RS 8 AIO I-M-DP SD Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W L H Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 1W L H Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 3W L H Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS16ES-T-L H/Z (conrad.cz)

Distributor module with 6 voltage potentials (P1,P2,P3,P4,P5,P6) in 12P1,12P2,12P3 ,12P4,12P5 and 12P6 for tension-clamp or screw connection. RS VERTIKÁLNÍ 6P 12X6 Z (conrad.cz)

Distributor module with 4 voltage potentials (P1,P2,P3,P4) in 20P1,20P2,20P3and 20P4 for tension-clamp or screw connection. RS VERTIKÁLNÍ 4P 20X4 Z (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT 32 LMZF (conrad.cz)

Compact interfaces for transmitting 32 digital input/output signals (RSF SPS). Signals optionally with byte grouping (can be set using jumper). Can be switched between positive or negative signal (set with jumper) An optional LED status display shows the status and the operating voltages. Each circuit can be protected by 5x20 mm individual fuses. Available with tension-clamp or screw connection. RSF PLC 2W 32 IO LED Z (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 I/O8 LMZF (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 INIT8 LD LMZF (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT32 LD LMZF (conrad.cz)

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F26 Z (conrad.cz)

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F10 Z (conrad.cz)

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F14 Z (conrad.cz)

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F50 Z (conrad.cz)

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F20 Z (conrad.cz)

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F34 Z (conrad.cz)

Passive interfaces for signal transmission on a flat-cable connector equipped with a tension-clamp connection in accordance with IEC 603-1 / DIN 41651. The main features include: Group with 10- to 64-pole connectors One-to-one electrical connection between controller and field connections. Very compact modules can be attached to conventional TS35 or TS32 mounting rails. Longer attachment hooks RS F40 Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DIOHV-Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 2W I-L H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W I-L H S (conrad.cz)

Insulated FTAs for Honeywell C300 IOTA digital input/output. Insulated interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. High current switching capacity in a compact design Possibility of feeding the IOTA from the FTA (fuse protected) Screw or tension clamp connection FTA-C300 32 DO-RSLIM-Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-LD-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-SH-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-TEST Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DI-LD-Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-FUSE-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI-SH-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI TESTOVACÍ Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 1W I R S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 3W I R S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 1W I-L H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 1W I-L H S (conrad.cz)

The analogue interfaces are equipped with SubD connectors. Thus they offer sufficient shielding for analogue signal transmission. They are also equipped with very useful isolators and test sockets for measuring voltage or current. RS 8 AI1AO MICRO SD S (conrad.cz)

Digital output interface per-relay for electrical signal transmission between the PLC and the field. Electrical isolation by pluggable relays. Integrated LED status display. Screw or tension clamp-connection. Additional functions: in-series fuse or isolator 2 versions available: compact (RSS relay) or standard (RCL relay). RSM-16 2CO Z (conrad.cz)

Digital output interface per-relay for electrical signal transmission between the PLC and the field. Electrical isolation by pluggable relays. Integrated LED status display. Screw or tension clamp-connection. Additional functions: in-series fuse or isolator 2 versions available: compact (RSS relay) or standard (RCL relay). RSM-8 C 1CO Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 2W H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W R S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 2W R S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 2W F R S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W F R S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 2W L H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 16 IO 2W F H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 8 IO 2W L H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 12 IO 2W L H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W L H S (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W F H S (conrad.cz)

Passive interfaces for signal transmission on a SubD connector equipped with a tension-clamp connection in accordance with IEC 807-2 / DIN 41652. The main features include: Group with 9-, 15-, 37- and 50-pole male and female connectors. One-to-one electrical connection between controller and field connections. Extremely compact modules for attachment to standard TS35 or TS32 rail. RS SD37 SZ (conrad.cz)

Passive interfaces for signal transmission on a SubD connector equipped with a tension-clamp connection in accordance with IEC 807-2 / DIN 41652. The main features include: Group with 9-, 15-, 37- and 50-pole male and female connectors. One-to-one electrical connection between controller and field connections. Extremely compact modules for attachment to standard TS35 or TS32 rail. RS SD37 BZ (conrad.cz)