Waveseries, voltage monitoring, 1, 1, tension clamp connection weidmüller waz2 vma v ac 8581230000 1 ks

The WAS/WAZ2 VMA V ac: single-phase AC voltage monitoring components with analogue output and external power supply. On the input side, these components provide voltages in the ranges 0 to 30/70/130/260 and 450 VAC for measuring. A standardised DC current/voltage signal is available on the output side. The devices use the true RMS method and are capable of measuring voltages in the frequency range from 40 to 400 Hz with an accuracy of 1 to 2%. The input/output and supply are securely isolated with 4 kV. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N jumpers on the module side. WAZ2 VMA V ac (conrad.cz)

Output current loop fed AC current monitoring components WAS/WAZ1 CMA LP. They can measure single-phase 50/60 Hz AC currents of up to 10 A using the Root Mean Square (RMS) method on the input side. They can also be switched between three ranges. No external power supply is used; the supply is only via the 4...20 mA current loop on the output side. The input and output circuits are securely isolated with 4 kV. The monitoring components come in a 17.5-mm-wide WAVEBOX housing. These devices can be used in many process automation applications because they are not dependent on an external power supply. International approvals (such as ATEX Zone 2 and UL C1D2) also permit usage in explosion-risk zones. WAZ1 CMA LP 1/5/10 A ac (conrad.cz)

WAS/WAZ5 DC/Alarm analogue DC current/voltage signal converters with integrated limit-value monitoring and external power supply. The input and output parameters can be configured. During operation, the analogue value on the input side is continuously monitored. The upper and lower operating points can be adjusted and are switched via relays. Various monitoring functions such as fail-safe, non fail-safe, high-/low trip and hysteresis can be adjusted via DIP switches. The WAS/WAZ5 DC/Alarm is constructed with 3-way isolation. Either screw or tension-clamp wire connections are available for the monitoring modules. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N cross-connectors on the module side. The 17.5 mm wide monitoring components can be used anywhere within the electrical cabinet or in process and industrial automation applications. WAZ5 DC/alarm (conrad.cz)

WAS / 2 VMR 1ph/3ph: AC/DC voltage monitoring components with digital output and external supply Depending on the version, the input side can be used to measure and monitor single-phase voltages up to 260 VAC/DC or three-phase voltages up to 400 VAC/DC. There are one or two digital switching outputs for direct under-voltage or surge voltage monitoring available on the output side. The switching thresholds, low/high trip limits and hysteresis can be adjusted as required. The input and output circuits have 4 kV of electrical isolation. The monitoring components can be mounted on a DIN rail and are integrated in a 22.5 mm wide housing. Co2 VMR 3ph (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 V 0-10 V (conrad.cz)

WAS/WAZ6 TTA is a universal signal converter and trip amplifier that can be configured on the PC. Combines the functions of isolation, transmission, linearisation and trip amplification in a single module. These exceptional characteristics and outstanding configurability combine to make the TTA truly unique. The TTA functions with stability and precision under a wide range of voltages and ambient temperatures. It is compatible with all standard sensor types. Universal input signals: temperature signals such as resistance thermometer, thermocouple, potentiometer, frequency transmitter, DC voltage signals and current signals Loop-powered or passive input Wide-range power supply: 18 – 264 V AC/DC User-defined linearization Inputs and outputs can be configured on PC Combined analogue and relay output Ambient temperature range: -40 °C …70 °C The CBX200 USB interface is used to connect to the PC. The WAS/WAZ6 TTA is also offered as an option with ATEX Zone 2 and UL C1D2 approvals. WAZ6 TTA EX (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DIOHV-Z (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 C 0/4 až 20 mA (conrad.cz)

The ACT20M-CI-CO-ILP, MCZ CCC and WAS5 CCC LP are 1/2-channel passive isolators that are supplied via the input loop current. They are optionally available in 6 mm (ACT20M/ MCZ series) or 17.5 mm (WAS5 CCC LP) housings. The input and output circuits are completely, electrically isolated from each other. The passive isolators are designed with 1 or 2 channels. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Passive isolators are used to electrically isolate normalised signals (from 0/4 to 20 mA).The modules get their power supply from the current loop on the input side. The power for signal transmission and supply comes from the active 0/4–20 mA signal. They have very low current consumption and can be used anywhere in the field where no suitable power supply is available. These devices are used in a variety of application processes as signal isolators and signal multipliers. They can be used to eliminate measurement errors caused by differences in earth potentials. WAZ5 CCC LP 0-20 / 0-20mA (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 C 0/4 až 20 mA (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 C 0/4 až 20 mA (conrad.cz)

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ5 VCC 0-10 V / 4-20MA (conrad.cz)

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ5 VVC 0-10 V / 0-10 V (conrad.cz)

Insulated FTAs for Honeywell C300 IOTA digital input/output. Insulated interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. High current switching capacity in a compact design Possibility of feeding the IOTA from the FTA (fuse protected) Screw or tension clamp connection FTA-C300 32 DO-RSLIM-Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-LD-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-SH-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-TEST Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DI-LD-Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-FUSE-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI-SH-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI TESTOVACÍ Z (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 I/O8 LMZF (conrad.cz)

The externally supplied ACT20M-CI-CO, MAS RPS/RPSH, MCZ CFC and WAS/WAZ 4/5 C signal converters/supply isolators can transmit, isolate and convert standardised DC current signals. They are optionally available in widths of 6 mm (ACT20M/MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (ACT20M, WAS/WAZ) or into a proportional frequency (MCZ CFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5) so that they can process signals quickly. The MAS/RPS/RPSH supply isolator can supply 2-wire sensors externally. They can also be used optionally to transmit the HART protocol (MAS RPSH). The 24 VDC supply voltage can be cross-connected on the module side via the CH20M BUS profile (ACT20M series) or using the ZQV4N (MAS/MCZ) or ZQV 2.5N (WAS/WAZ) pluggable jumpers. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. WAZ4 CVC DC 4-20/0-10 V (conrad.cz)

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ4 VVC DC 0-10/0-10 V (conrad.cz)

Ochranný spínač motoru Eaton PKZM01-1, 690 V/AC 1 A, 1 ks od výrobce Eaton v kategorii Pojistkové odpínače za skvělou cenu u Conrada. (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT 32 LMZF (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Upozornění: Při popisu spínacích poloh se udává hodnota bez závorky nebo v závorce. Bez závorky: s funkcí aretace Se závorkou: s funkcí tlačítka (conrad.cz)

Instalační stykač Finder 22.64.0.230.4717 22.64.0.230.4717, 230 V/AC, 240 V/AC, 1 ks od výrobce Finder v kategorii Stykače za skvělou cenu u Conrada. (conrad.cz)

Instalační stykač Finder 22.44.0.230.4717 22.44.0.230.4717, 230 V/AC, 240 V/AC, 1 ks od výrobce Finder v kategorii Stykače za skvělou cenu u Conrada. (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 INIT8 LD LMZF (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT32 LD LMZF (conrad.cz)

Output current loop fed AC current monitoring components WAS/WAZ1 CMA LP. They can measure single-phase 50/60 Hz AC currents of up to 10 A using the Root Mean Square (RMS) method on the input side. They can also be switched between three ranges. No external power supply is used; the supply is only via the 4...20 mA current loop on the output side. The input and output circuits are securely isolated with 4 kV. The monitoring components come in a 17.5-mm-wide WAVEBOX housing. These devices can be used in many process automation applications because they are not dependent on an external power supply. International approvals (such as ATEX Zone 2 and UL C1D2) also permit usage in explosion-risk zones. Co1 CMA LP 1/5/10 A ac (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Síťový odrušovací filtr s univerzální paticí pro montáž na lišty typu NS 32 a NS 35/7,5 (conrad.cz)

Output current loop fed AC current monitoring components WAS/WAZ1 CMA LP. They can measure single-phase 50/60 Hz AC currents of up to 10 A using the Root Mean Square (RMS) method on the input side. They can also be switched between three ranges. No external power supply is used; the supply is only via the 4...20 mA current loop on the output side. The input and output circuits are securely isolated with 4 kV. The monitoring components come in a 17.5-mm-wide WAVEBOX housing. These devices can be used in many process automation applications because they are not dependent on an external power supply. International approvals (such as ATEX Zone 2 and UL C1D2) also permit usage in explosion-risk zones. Co1 CMA LP 1/5/10 A EX (conrad.cz)

Spínač a senzor integrovány v jednom pouzdře. Upevnění na zdi nebo na osvětlovacím stožáru. Schválení: CE. Schválení: GOST, IMQ. (conrad.cz)

Spínač a senzor jsou integrované v jednom pouzdře. Upevnění na zeď nebo na sloup osvětlení. Práh sepnutí lze nastavit v rozmezí 1 - 80 lx. Schválení: GOST. (conrad.cz)

Soumrakový spínač pro světlem řízené ovládání osvětlení se samostatným světelným senzorem pro montáž do rozvaděče. Nízká spotřeba energie, šířka modulu: 17,5 mm. Schválení: IMQ. Světelný senzor. (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 1W L H Z (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Při popisu spínacích poloh udává hodnota v závorce to, že se jedná o funkci stisku. (conrad.cz)

Odrušovací filtr Yunpen YK01T1, 250 V/AC, 250 V/AC, 1 A, 1 A od výrobce Yunpen v kategorii Odrušovací filtr za skvělou cenu u Conrada. (conrad.cz)