Rtd transformer, tension clamp connection weidmüller wtz4 pt100/4 v 0-10v 8432250000 1 ks

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 C 0/4 až 20 mA (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 C 0/4 až 20 mA (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 C 0/4 až 20 mA (conrad.cz)

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ5 VVC 0-10 V / 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTS4 PT100/4 C 0/4 až 20 mA (conrad.cz)

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ5 VCC 0-10 V / 4-20MA (conrad.cz)

The externally supplied ACT20M-CI-CO, MAS RPS/RPSH, MCZ CFC and WAS/WAZ 4/5 C signal converters/supply isolators can transmit, isolate and convert standardised DC current signals. They are optionally available in widths of 6 mm (ACT20M/MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (ACT20M, WAS/WAZ) or into a proportional frequency (MCZ CFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5) so that they can process signals quickly. The MAS/RPS/RPSH supply isolator can supply 2-wire sensors externally. They can also be used optionally to transmit the HART protocol (MAS RPSH). The 24 VDC supply voltage can be cross-connected on the module side via the CH20M BUS profile (ACT20M series) or using the ZQV4N (MAS/MCZ) or ZQV 2.5N (WAS/WAZ) pluggable jumpers. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. WAZ4 CVC DC 4-20/0-10 V (conrad.cz)

The MCZ VFC and WAS/WAZ4/5 signal converters can transmit, isolate and convert analogue DC voltages. They are optionally available in widths of 6 mm (MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (WAS/WAZ) or into a proportional frequency (MCZ VFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5). The 24 VDC supply voltage can be cross-connected on the module side using ZQV4N (MCZ) or ZQV 2,5N (WAS/WAZ) jumpers. WAZ4 VVC DC 0-10/0-10 V (conrad.cz)

The ACT20M-CI-CO-ILP, MCZ CCC and WAS5 CCC LP are 1/2-channel passive isolators that are supplied via the input loop current. They are optionally available in 6 mm (ACT20M/ MCZ series) or 17.5 mm (WAS5 CCC LP) housings. The input and output circuits are completely, electrically isolated from each other. The passive isolators are designed with 1 or 2 channels. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Passive isolators are used to electrically isolate normalised signals (from 0/4 to 20 mA).The modules get their power supply from the current loop on the input side. The power for signal transmission and supply comes from the active 0/4–20 mA signal. They have very low current consumption and can be used anywhere in the field where no suitable power supply is available. These devices are used in a variety of application processes as signal isolators and signal multipliers. They can be used to eliminate measurement errors caused by differences in earth potentials. WAZ5 CCC LP 0-20 / 0-20mA (conrad.cz)

WAS/WAZ5 DC/Alarm analogue DC current/voltage signal converters with integrated limit-value monitoring and external power supply. The input and output parameters can be configured. During operation, the analogue value on the input side is continuously monitored. The upper and lower operating points can be adjusted and are switched via relays. Various monitoring functions such as fail-safe, non fail-safe, high-/low trip and hysteresis can be adjusted via DIP switches. The WAS/WAZ5 DC/Alarm is constructed with 3-way isolation. Either screw or tension-clamp wire connections are available for the monitoring modules. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N cross-connectors on the module side. The 17.5 mm wide monitoring components can be used anywhere within the electrical cabinet or in process and industrial automation applications. WAZ5 DC/alarm (conrad.cz)

The MAS/MAZ PT100 temperature signal isolating converter with external power supply in 6.1 mm width: for recording, transmitting and isolating 2-/3-wire PT100 sensors. DC current signals and standardised voltage signals are available on the output side. They can be adjusted using the DIP switches. The input and outputs are designed with 0.5 kV of electrical isolation. The output circuit is used to supply 24 VDC. It can be bridged on the module side using pluggable ZQV 4N cross-connectors. The PT100 signal isolating converters have either a screw or tension-clamp wire connection. They can be used in many applications around the world because of their international approvals (cULus, C1D2 and ATEX Zone2). MAZ PT100 0 - 100C (conrad.cz)

The WAS/WAZ2 VMA V ac: single-phase AC voltage monitoring components with analogue output and external power supply. On the input side, these components provide voltages in the ranges 0 to 30/70/130/260 and 450 VAC for measuring. A standardised DC current/voltage signal is available on the output side. The devices use the true RMS method and are capable of measuring voltages in the frequency range from 40 to 400 Hz with an accuracy of 1 to 2%. The input/output and supply are securely isolated with 4 kV. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N jumpers on the module side. WAZ2 VMA V ac (conrad.cz)

WAS/WAZ6 TTA is a universal signal converter and trip amplifier that can be configured on the PC. Combines the functions of isolation, transmission, linearisation and trip amplification in a single module. These exceptional characteristics and outstanding configurability combine to make the TTA truly unique. The TTA functions with stability and precision under a wide range of voltages and ambient temperatures. It is compatible with all standard sensor types. Universal input signals: temperature signals such as resistance thermometer, thermocouple, potentiometer, frequency transmitter, DC voltage signals and current signals Loop-powered or passive input Wide-range power supply: 18 – 264 V AC/DC User-defined linearization Inputs and outputs can be configured on PC Combined analogue and relay output Ambient temperature range: -40 °C …70 °C The CBX200 USB interface is used to connect to the PC. The WAS/WAZ6 TTA is also offered as an option with ATEX Zone 2 and UL C1D2 approvals. WAZ6 TTA EX (conrad.cz)

Output current loop fed AC current monitoring components WAS/WAZ1 CMA LP. They can measure single-phase 50/60 Hz AC currents of up to 10 A using the Root Mean Square (RMS) method on the input side. They can also be switched between three ranges. No external power supply is used; the supply is only via the 4...20 mA current loop on the output side. The input and output circuits are securely isolated with 4 kV. The monitoring components come in a 17.5-mm-wide WAVEBOX housing. These devices can be used in many process automation applications because they are not dependent on an external power supply. International approvals (such as ATEX Zone 2 and UL C1D2) also permit usage in explosion-risk zones. WAZ1 CMA LP 1/5/10 A ac (conrad.cz)

Configurable RTD signal isolator/converter WAS5/WAZ5 PRO RTD with external power supply with 17.5 mm width, for recording, transforming and isolating RTD sensors in standardised DC current and voltage signals 2-/3-/4-wire PT100, PT1000, Ni100, Ni10000, Cu10/25/50/100, potentiometers or fixed resistors can optionally be connected on the input side. The input and output parameters (e.g. sensor type, temperature range and standardised output signal) can be configured using the DIP switches. The input/output channels and 24 V DC power supply are completely isolated with 4 kV. The PRO RTD isolating transformers come with either a screw or tension-clamp wire connection. The 24 V DC supply voltage can be bridged using pluggable ZQV 2.5N jumpers on the module side. Most models can be adjusted and set using the WAVETOOL program available from Weidmüller's website. They can be used in many applications around the world because of their international approvals such as cULus, CULusEX and GL. Co5 PRO RTD Cu (conrad.cz)

DimLED přijímač slouží jako hlavní řídící jednotka, která řídí signálem 0/1-10V DimLED stmívač 065503. viz obrázky nebo návod. Na tento přijímač lze tedy připojit až 4 jednotky 065503 a ovládat je dohromady jedním ovladačem. Pro ovládání více okruhů je nutno použít jeden přijímač na každý okruh. Na každý přijímač lze napárovat až 10 různých ovladačů řady dimLED a tak ovládat z několika míst. V případě přerušení a poté opětovného připojení napájení (například přerušením napájení zdroje) má tento přijímač paměť nastavení intenzity (intenzita osvětlení se vrátí na naposled nastavenou). Doporučujeme přijímač, instalovat v min. 30-50 cm vzdálenosti od zdroje rušení, tedy např.: (kovových konstrukcí, napětí 230 V, transformátorů, LED driverů, AL profilů atd.), Pokud je to možné, tak přijímač natočit textem směrem k ovladači. Přijímač má anténu, pod textem. (eshop.ledsolution.cz)

Distributor module with 4 voltage potentials (P1,P2,P3,P4) in 20P1,20P2,20P3and 20P4 for tension-clamp or screw connection. RS VERTIKÁLNÍ 4P 20X4 Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DIOHV-Z (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT 32 LMZF (conrad.cz)

Insulated FTAs for Honeywell C300 IOTA digital input/output. Insulated interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. High current switching capacity in a compact design Possibility of feeding the IOTA from the FTA (fuse protected) Screw or tension clamp connection FTA-C300 32 DO-RSLIM-Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-LD-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-SH-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AO-TEST Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DI-LD-Z (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DO-FUSE-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI-SH-Z (conrad.cz)

Analogue input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 analog IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. 2 units may also be used for the digital IOTAs. Disconnecting plugs and test points (2mm in diameter) for voltage and current measurements. The FTAs incorporate an M4 connection for the shielding. Screw or tension clamp connection FTA-C300 16AI TESTOVACÍ Z (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 I/O8 LMZF (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F10 INIT8 LD LMZF (conrad.cz)

Passive RS F40 or RS F10 interface elements for 32 or 8 signals: these enable an efficient connection of peripherals (sensors and actuators) to the input/output modules of the PLC using pre-assembled cables. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. 1-, 2- or 3-wire technology. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 INIT32 LD LMZF (conrad.cz)

DC/f transformer, Screw connection Weidmüller DK U-F DK5 0-10V 8242040000 10 ks od výrobce Weidmüller v kategorii Měniče, ostatní za skvělou cenu u Conrada. (conrad.cz)

Digital output interface per-relay for electrical signal transmission between the PLC and the field. Electrical isolation by pluggable relays. Integrated LED status display. Screw or tension clamp-connection. Additional functions: in-series fuse or isolator 2 versions available: compact (RSS relay) or standard (RCL relay). RSM-16 2CO Z (conrad.cz)

Distributor module with 6 voltage potentials (P1,P2,P3,P4,P5,P6) in 12P1,12P2,12P3 ,12P4,12P5 and 12P6 for tension-clamp or screw connection. RS VERTIKÁLNÍ 6P 12X6 Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS16ES-T-L H/Z (conrad.cz)

Digital output interface per-relay for electrical signal transmission between the PLC and the field. Electrical isolation by pluggable relays. Integrated LED status display. Screw or tension clamp-connection. Additional functions: in-series fuse or isolator 2 versions available: compact (RSS relay) or standard (RCL relay). RSM-8 C 1CO Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 1W L H Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 3W L H Z (conrad.cz)

The digital direct input/output interfaces are supplied with flat cable connectors to facilitate connection. They are available in tension clamp or clamping yoke connection, with elements such as fuses, disconnectors or LEDs. RS 32 IO 2W L H Z (conrad.cz)

Čtyřkanálový LED ovladač pro jednobarevné osvětlení je bezdrátový radiofrekvenční ovládací systém, jednoho ovladače a několik přijímačů. S jedním ovladačem lze ovládat nezávisle 4 zóny, která se může skládat z několika přijímačů. Tyto přijímače se po sehrání na jednotlivé předvolbě na ovladači ovládají jako jedna sekce. Ovladač také umožňuje ovládat až 4 zařízení se signálem 0-10V, případně 1-10V. Přijímač může být ukrytý (za zdí, sádrokartónem či ve skříni), není nutná přímá viditelnost přijímače pro ovladač. Ovládání probíhá na dotykové lince uprostřed ovladače. Vlastnosti a výhody systému dimLED: Stmívání je stabilní a spolehlivé, dosah ovladače ≤ 30M. Stmívání v rozmezí 0-100%, stmívání měkké, bez blikání. Při zapnutí dojde k pozvolnému rozsvícení, při vypnutí dojde k pozvolnému setmění. Ovládání: Ovládání probíhá na dotykové lince uprostřed ovladače. Dotykem na lince dochází k nastavování intenzity. Tlačítka na krajích ovladače slouží k dalším možnostem ovládání a vybírání zón. (eshop.ledsolution.cz)

Čtyřkanálový LED ovladač pro jednobarevné osvětlení je bezdrátový radiofrekvenční ovládací systém, jednoho ovladače a několik přijímačů. S jedním ovladačem lze ovládat nezávisle 4 zóny, která se může skládat z několika přijímačů. Tyto přijímače se po sehrání na jednotlivé předvolbě na ovladači ovládají jako jedna sekce. Ovladač také umožňuje ovládat až 4 zařízení se signálem 0-10V, případně 1-10V. Přijímač může být ukrytý (za zdí, sádrokartónem či ve skříni), není nutná přímá viditelnost přijímače pro ovladač. Ovládání probíhá na dotykové lince uprostřed ovladače. Vlastnosti a výhody systému dimLED: Stmívání je stabilní a spolehlivé, dosah ovladače ≤ 30M. Stmívání v rozmezí 0-100%, stmívání měkké, bez blikání. Při zapnutí dojde k pozvolnému rozsvícení, při vypnutí dojde k pozvolnému setmění. Ovládání: Ovládání probíhá na dotykové lince uprostřed ovladače. Dotykem na lince dochází k nastavování intenzity. Tlačítka na krajích ovladače slouží k dalším možnostem ovládání a vybírání zón. (eshop.ledsolution.cz)

Compact interfaces for transmitting 32 digital input/output signals (RSF SPS). Signals optionally with byte grouping (can be set using jumper). Can be switched between positive or negative signal (set with jumper) An optional LED status display shows the status and the operating voltages. Each circuit can be protected by 5x20 mm individual fuses. Available with tension-clamp or screw connection. RSF PLC 2W 32 IO LED Z (conrad.cz)

The analogue interfaces are equipped with SubD connectors. Thus they offer sufficient shielding for analogue signal transmission. They are also equipped with very useful isolators and test sockets for measuring voltage or current. RS 8 AIO I-M-DP SD Z (conrad.cz)