Rtd isolating transformer, screw connection weidmüller was5 pro rtd cu 8638950000 1 ks

Configurable RTD signal isolator/converter WAS5/WAZ5 PRO RTD with external power supply with 17.5 mm width, for recording, transforming and isolating RTD sensors in standardised DC current and voltage signals 2-/3-/4-wire PT100, PT1000, Ni100, Ni10000, Cu10/25/50/100, potentiometers or fixed resistors can optionally be connected on the input side. The input and output parameters (e.g. sensor type, temperature range and standardised output signal) can be configured using the DIP switches. The input/output channels and 24 V DC power supply are completely isolated with 4 kV. The PRO RTD isolating transformers come with either a screw or tension-clamp wire connection. The 24 V DC supply voltage can be bridged using pluggable ZQV 2.5N jumpers on the module side. Most models can be adjusted and set using the WAVETOOL program available from Weidmüller's website. They can be used in many applications around the world because of their international approvals such as cULus, CULusEX and GL. Co5 PRO RTD Cu (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTS4 PT100/4 C 0/4 až 20 mA (conrad.cz)

The MAS/MAZ PT100 temperature signal isolating converter with external power supply in 6.1 mm width: for recording, transmitting and isolating 2-/3-wire PT100 sensors. DC current signals and standardised voltage signals are available on the output side. They can be adjusted using the DIP switches. The input and outputs are designed with 0.5 kV of electrical isolation. The output circuit is used to supply 24 VDC. It can be bridged on the module side using pluggable ZQV 4N cross-connectors. The PT100 signal isolating converters have either a screw or tension-clamp wire connection. They can be used in many applications around the world because of their international approvals (cULus, C1D2 and ATEX Zone2). MAZ PT100 0 - 100C (conrad.cz)

Dioda směrového tlačítka Eltako RTD 60000015, 1 ks od výrobce Eltako v kategorii Příslušenství pro spínače, nouzové vypínače, tlačítka s osvětlením a kont. prvky za skvělou cenu u Conrada. (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 V 0-10 V (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/3 C 0/4 až 20 mA (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/4 C 0/4 až 20 mA (conrad.cz)

The configurable WTS4/WTZ4 PT100 temperature signal converter with external power supply in 12.5 mm width, for recording and transforming PT100 sensors in standardised DC current and voltage signals. 2-, 3- and 4-wire PT100 sensors can be connected on the input side. The temperature ranges can be selected using DIP switches. The input and output circuits are not electrically isolated from each other. The output is used for the 24 VDC power supply. The WTS4/WT/4 Thermo comes with either a screw or tension-clamp wire connection. The 24 VDC supply voltage can be bridged using pluggable ZQV 2,5N jumpers on the module side. WTZ4 PT100/2 C 0/4 až 20 mA (conrad.cz)

The ACT20M-CI-CO-ILP, MCZ CCC and WAS5 CCC LP are 1/2-channel passive isolators that are supplied via the input loop current. They are optionally available in 6 mm (ACT20M/ MCZ series) or 17.5 mm (WAS5 CCC LP) housings. The input and output circuits are completely, electrically isolated from each other. The passive isolators are designed with 1 or 2 channels. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Passive isolators are used to electrically isolate normalised signals (from 0/4 to 20 mA).The modules get their power supply from the current loop on the input side. The power for signal transmission and supply comes from the active 0/4–20 mA signal. They have very low current consumption and can be used anywhere in the field where no suitable power supply is available. These devices are used in a variety of application processes as signal isolators and signal multipliers. They can be used to eliminate measurement errors caused by differences in earth potentials. Co5 CCC LP 0-20 / 0-20mA (conrad.cz)

The ACT20M-CI-CO-ILP, MCZ CCC and WAS5 CCC LP are 1/2-channel passive isolators that are supplied via the input loop current. They are optionally available in 6 mm (ACT20M/ MCZ series) or 17.5 mm (WAS5 CCC LP) housings. The input and output circuits are completely, electrically isolated from each other. The passive isolators are designed with 1 or 2 channels. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Passive isolators are used to electrically isolate normalised signals (from 0/4 to 20 mA).The modules get their power supply from the current loop on the input side. The power for signal transmission and supply comes from the active 0/4–20 mA signal. They have very low current consumption and can be used anywhere in the field where no suitable power supply is available. These devices are used in a variety of application processes as signal isolators and signal multipliers. They can be used to eliminate measurement errors caused by differences in earth potentials. Co5 CCC LP 0-20 / 0-20mA (conrad.cz)

Náhrada stravy RTD je kompletní náhrada jídla v podobě nápoje s vyrovnaným obsahem živin. Jeho konzumací přijmete potřebné bílkoviny, sacharidy, tuky, minerály a vitamíny. Nápoj si můžete vzít kamkoliv s sebou a zahnat hlad chutným a zdravým způsobem. (gymbeam.cz)

Náhrada stravy RTD je kompletní náhrada jídla v podobě nápoje s vyrovnaným obsahem živin. Jeho konzumací přijmete potřebné bílkoviny, sacharidy, tuky, minerály a vitamíny. Nápoj si můžete vzít kamkoliv s sebou a zahnat hlad chutným a zdravým způsobem. (gymbeam.cz)

Náhrada stravy RTD je kompletní náhrada jídla v podobě nápoje s vyrovnaným obsahem živin. Jeho konzumací přijmete potřebné bílkoviny, sacharidy, tuky, minerály a vitamíny. Nápoj si můžete vzít kamkoliv s sebou a zahnat hlad chutným a zdravým způsobem. (gymbeam.cz)

Náhrada stravy RTD je chutnou tekutou alternativou pevného jídla, která vám kdykoliv pomůže zahnat hlad. Obsahuje 25 g kvalitních bílkovin, komplexní sacharidy a také široké spektrum vitamínů a minerálních látek. Díky tomu vás spolehlivě zasytí a dodá živiny, které jsou potřebné pro správnou funkci organismu. Navíc je vhodná i pro vegany. (gymbeam.cz)

Náhrada stravy RTD je kompletní náhrada jídla v podobě nápoje s vyrovnaným obsahem živin. Jeho konzumací přijmete potřebné bílkoviny, sacharidy, tuky, minerály a vitamíny. Nápoj si můžete vzít kamkoliv s sebou a zahnat hlad chutným a zdravým způsobem. (gymbeam.cz)

Náhrada stravy RTD je kompletní náhrada jídla v podobě nápoje s vyrovnaným obsahem živin. Jeho konzumací přijmete potřebné bílkoviny, sacharidy, tuky, minerály a vitamíny. Nápoj si můžete vzít kamkoliv s sebou a zahnat hlad chutným a zdravým způsobem. (gymbeam.cz)

Náhrada stravy RTD je kompletní náhrada jídla v podobě nápoje s vyrovnaným obsahem živin. Jeho konzumací přijmete potřebné bílkoviny, sacharidy, tuky, minerály a vitamíny. Nápoj si můžete vzít kamkoliv s sebou a zahnat hlad chutným a zdravým způsobem. (gymbeam.cz)

Náhrada stravy RTD je chutnou tekutou alternativou pevného jídla, která vám kdykoliv pomůže zahnat hlad. Obsahuje 25 g kvalitních bílkovin, komplexní sacharidy a také široké spektrum vitamínů a minerálních látek. Díky tomu vás spolehlivě zasytí a dodá živiny, které jsou potřebné pro správnou funkci organismu. Navíc je vhodná i pro vegany. (gymbeam.cz)

Sýtený funkčný nápoj pre zvýšenie energie, bdelosti a sústredenia. (protein.cz)

Sýtený funkčný nápoj pre zvýšenie energie, bdelosti a sústredenia. (protein.cz)

Weider RUSH RTD carbonated drink, Berry Blast, 250 ml RUSH RTD: doplněk stravy. Sycený nápoj ,obsahující L-citrullin malát, beta-alanin, L-arginin, L-alanyl-L-glutamin, taurin, glukuronolakton, kofein, niacin a zinek. Se sladidly. Obsahuje vyšší množství kofeinu (80mg/balení). (pilulka.cz)

Sýtený funkčný nápoj pre zvýšenie energie, bdelosti a sústredenia. (protein.cz)

Sýtený funkčný nápoj pre zvýšenie energie, bdelosti a sústredenia. (protein.cz)

Redukce ELEKTROBOCK HD20 pro ventily typu Danfoss RTD 000166 (tipa.eu)

WAS/WAZ5 DC/Alarm analogue DC current/voltage signal converters with integrated limit-value monitoring and external power supply. The input and output parameters can be configured. During operation, the analogue value on the input side is continuously monitored. The upper and lower operating points can be adjusted and are switched via relays. Various monitoring functions such as fail-safe, non fail-safe, high-/low trip and hysteresis can be adjusted via DIP switches. The WAS/WAZ5 DC/Alarm is constructed with 3-way isolation. Either screw or tension-clamp wire connections are available for the monitoring modules. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N cross-connectors on the module side. The 17.5 mm wide monitoring components can be used anywhere within the electrical cabinet or in process and industrial automation applications. DC/alarm CO5 (conrad.cz)

DC/f transformer, Screw connection Weidmüller DK U-F DK5 0-10V 8242040000 10 ks od výrobce Weidmüller v kategorii Měniče, ostatní za skvělou cenu u Conrada. (conrad.cz)

Weidmüller SSCH 10X3X1000 CU/SN 0348900000, 1 ks od výrobce Weidmüller v kategorii Příslušenství pro řadové svorkovnice Weidmüller za skvělou cenu u Conrada. (conrad.cz)

NakuptePřípravek proti mšicím a sviluškám NATURA Rock Effect NEW RTD 500mlz kategorieDům a zahrada > Zahrada > Pěstování > Insekticidy proti škůdcůmza119.00Kč (tipa.eu)

Měřicí převodník pro odporový teploměr a odporový dálkový vysílač. Konfigurovatelný, 3cestný dělený měřicí převodník se zásuvnou přípojnou technikou. Přístroj je určen pro připojení odporových teploměrů a odporových dálkových ovladačů ve 2-, 3- a 4vodičové technice. Naměřené hodnoty jsou převedeny v jeden lineární a volně nastavitelný proudový nebo napěťový signál. Standardní konfigurace (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

The MCZ PT100/3 CLP output loop-powered PT100 signal converter comes in a 6 mm wide terminal-block housing. . These signal converters are designed for specific temperature ranges and can be used to connect 2- and 3-wire PT100 sensors.. A 4...20mA current loop-fed signal is available on the output side. The input and output circuits in the MCZ PT100/3 CLP are not electrically isolated. The signal converters can be mounted on a TS35 DIN rail. They feature a high degree of accuracy and linearity. (conrad.cz)

Kompaktní, výkonný a jednoduchý Siemens LOGO! 8 je logický modul nové generace. Splňuje téměř všechny požadavky uživatelů a snadno se ovládá. Logický modul přesvědčí mnoha skvělými vlastnostmi od podsvícených ovládacích prvků až po bezdrátovou synchronizaci s tabletem či smartphonem. Mezi další zajímavé funkce patří zaslání varovné SMS. To vše při zachování přehledného a jednoduchého ovládání. Siemens LOGO! 8 je zcela nová generace zařízení pro průmyslovou automatizaci. Všechny základní stanice LOGO! 8 mohou komunikovat přes ethernetovou síť. Nabízejí mnoho funkcí pro dálkové ovládání a vzdálený přístup přes webový server a snadnou konfiguraci pomocí Drag and Drop. Kompaktní rozměry jen 72 mm (4 TE) šetří místo v rozváděči. Šestiřádkový displej s 16 znaky na řádek a nastavitelným podsvícením přehledně zobrazuje potřebné informace s jasným barevným označením. Externí 6řádkový displej s 20 znaky na řádek je vybaven 4 funkčními tlačítky a lze jej připojit k základní jednotce přes síťové rozhraní Ethernet. Se 7 digitálními, 3 analogovými a rozličnými napájecími moduly můžete LOGO! 8 doplňovat dle potřeby. Pro zapojení do sítě Ethernet slouží modul zastupující funkci switche, zatímco varování a zasílání varovných SMS obstarává nový modul LOGO! 8 CMR. Pomocí GPS signálu umožňuje také snadné zjišťování polohy a automatickou synchronizaci času. Díky integrovanému webovému serveru lze LOGO! 8 také velmi snadno sledovat a ovládat přes Wi-Fi nebo internet. Webové stránky s přehledem a textem z externího displeje lze prohlížet ve všech běžných webových prohlížečích na PC, smartphonech a tabletech. Nastavení lze velmi snadno provést pomocí softwaru LOGO! Soft Comfort V8. LOGO! 8 je zpětně kompatibilní s předchozími verzemi. Pomocí LOGO! Soft Comfort V8 lze pohodlně přejmenovávat a upravovat nastavení programů. Propojení až 2x 8 základních jednotek pomocí sítě ethernet·Komunikace s kontroléry a panely SIMATIC a PC·Slot na SD kartu pro ukládání dat Upozornění: Software je pouze v EN nebo DE jazykové mutaci. (conrad.cz)

The WAS/WAZ PRO Freq f/DC isolating transformer in its compact housing is just 12.5 mm wide. It converts input frequencies of up to 100 KHz into standardised analogue signals. The devices can be configured as required using the DIP switches. The connection on the input side is suitable for both 2- and 3-wire PNP/NPN or Namur initiators. Lower-and upper measurement frequencies can be individually configured and assigned to a corresponding standardised current/voltage output using DIP switches or an external frequency generator (from 16 KHz). They have 4 kV of 3-way isolation and do not need to be calibrated separately. The 24 VDC supply voltage can be bridged using pluggable ZQV 2.5N jumpers on the module side. The f/DC isolating transformer comes in either screw or tension-clamp wire connection versions. Co4 Pro freq (conrad.cz)

The constantly increasing demand for automation technology means that ever larger amounts of data have to be processed. A highly diverse range of interface converters in serial and digital form are used in such instances. They are primarily used to adapt different data protocols and for converting analogue signals into digital ones or vice versa. WDS2 RS232/TTY (conrad.cz)

The constantly increasing demand for automation technology means that ever larger amounts of data have to be processed. A highly diverse range of interface converters in serial and digital form are used in such instances. They are primarily used to adapt different data protocols and for converting analogue signals into digital ones or vice versa. WDS2 RS232/RS485/422 (conrad.cz)

The ACT20M-CI-CO-OLP, WAS/WAZ5 OLP signal isolator/splitter (2-wire system) is supplied via the output current loop and has an analogue DC current input. The 1- and 2-channel signal isolators are supplied from the current loop. They are available in the 6.1 mm (ACT20M series) or 17.5 mm (WAVESERIES) housings. The input and output circuits are electrically isolated from each other. The power is supplied via the 4–20 mA current loop on the output side. The devices come optionally in a splitter version with two loop-fed outputs. The devices can be mounted on a DIN rail and consume minimal power. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Signal converters with output-loop power supplies are used in a variety of application processes as signal isolators and signal multipliers (splitters) and signal amplifiers. They can be used to eliminate measurement errors caused by differences in earth potentials. ACT20M-CI-CO-OLP-S (conrad.cz)

The ACT20M-CI-CO-OLP, WAS/WAZ5 OLP signal isolator/splitter (2-wire system) is supplied via the output current loop and has an analogue DC current input. The 1- and 2-channel signal isolators are supplied from the current loop. They are available in the 6.1 mm (ACT20M series) or 17.5 mm (WAVESERIES) housings. The input and output circuits are electrically isolated from each other. The power is supplied via the 4–20 mA current loop on the output side. The devices come optionally in a splitter version with two loop-fed outputs. The devices can be mounted on a DIN rail and consume minimal power. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Signal converters with output-loop power supplies are used in a variety of application processes as signal isolators and signal multipliers (splitters) and signal amplifiers. They can be used to eliminate measurement errors caused by differences in earth potentials. ACT20M-2CI 2CO-OLP-S (conrad.cz)

WAS/WAZ6 TTA is a universal signal converter and trip amplifier that can be configured on the PC. Combines the functions of isolation, transmission, linearisation and trip amplification in a single module. These exceptional characteristics and outstanding configurability combine to make the TTA truly unique. The TTA functions with stability and precision under a wide range of voltages and ambient temperatures. It is compatible with all standard sensor types. Universal input signals: temperature signals such as resistance thermometer, thermocouple, potentiometer, frequency transmitter, DC voltage signals and current signals Loop-powered or passive input Wide-range power supply: 18 – 264 V AC/DC User-defined linearization Inputs and outputs can be configured on PC Combined analogue and relay output Ambient temperature range: -40 °C …70 °C The CBX200 USB interface is used to connect to the PC. The WAS/WAZ6 TTA is also offered as an option with ATEX Zone 2 and UL C1D2 approvals. Co6 TTA EX (conrad.cz)

The MAS/MAZ thermal signal isolating converter with external power supply in 6.1 mm width: for recording, transmitting, linearising and isolating thermal signals in compliance with IEC 584, type K or J. DC current signals and standardised voltage signals are available on the output side. They can be adjusted using the DIP switches. The input and outputs are designed with 0.5 kV of electrical isolation. The output circuit is used to supply 24 VDC. It can be bridged on the module side using pluggable ZQV 4N cross-connectors. The thermal signal isolating converters have either a screw or tension-clamp wire connection. They can be used in many applications around the world because of their international approvals (cULus, C1D2 and ATEX Zone2). MAZ teploměr-J 0 - 700 °C output select (conrad.cz)

The externally supplied ACT20M-CI-CO, MAS RPS/RPSH, MCZ CFC and WAS/WAZ 4/5 C signal converters/supply isolators can transmit, isolate and convert standardised DC current signals. They are optionally available in widths of 6 mm (ACT20M/MCZ), 12.5 mm (WAS/WAZ4) or 17.5 mm (WAS/WAZ5). The input and output circuits are completely electrically isolated, as is the power supply. The input signal is converted into a DC current/voltage value (ACT20M, WAS/WAZ) or into a proportional frequency (MCZ CFC) between 0–1/4/8/16 KHz. The WAVESERIES signal converters are available with a limiting frequency of either 10 Hz (WAS/WAZ4) or 20 KHz (WAS/WAZ5) so that they can process signals quickly. The MAS/RPS/RPSH supply isolator can supply 2-wire sensors externally. They can also be used optionally to transmit the HART protocol (MAS RPSH). The 24 VDC supply voltage can be cross-connected on the module side via the CH20M BUS profile (ACT20M series) or using the ZQV4N (MAS/MCZ) or ZQV 2.5N (WAS/WAZ) pluggable jumpers. International approvals (such as ATEX Zone 2, UL C1D2 and FM Div2) permit use in explosion-risk zones. Co4 CCC DC 4-20 / 0-20MA (conrad.cz)

Digital input/output direct FTAs for Honeywell C300 IOTAs. Passive interfaces (FTA) for connecting the Honeywell C300 digital IOTAs. Clearly labelled: Same connector and position on the FTA and on the IOTA. The light indicator (LED) indicates the position of the switch. Possibility of feeding the IOTA from the FTA (fuse protected). Fuse protection per channel (optional). Screw or tension clamp connection. FTA-C300 32 DIOHV-S (conrad.cz)

In addition to heavy-duty connectors, RockStar® includes the appropriate accessories for effective, functional and safe system cabling; e.g. coding systems, shield clamps, cover plates and replacement seals HDC HP 250 SHOCKPROTEC (conrad.cz)

The RS F40 or RS F10 interface elements (for 32 or 8 signals) enable a relay to be used to isolate signals coming from the PLC with sensors and field actuators. The main characteristics are: Tension-clamp or screw connection system Signals grouped according to bytes. Extremely compact modules in RS 45 profile section for installation on standard TS35 mounting rail. RS F40 16RS OUT 24VDC (conrad.cz)