I/O ports and slots 16 SFP 100/1000 Mbps ports8 SFP dual-personality ports; 100/1000BaseX or 100/1000BASET RJ-45 Combo Ports4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Power supplies 2 power supply slots1 minimum power supply required (ordered separately) Physical characteristics Dimensions17.32(w) x 14.17(d) x 1.72(h) in (44 x 36 x 4.36 cm) (1U height)Weight17.64 lb (8 kg) Memory and processor 1 GB SDRAM, 128 MB flash; packet buffer size: 1.5 MB Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance 1000 Mb Latency < 5 µs10 Gbps Latency < 1.5 µsThroughput 96 MppsRouting/Switching capacity 128 GbpsRouting table size 512 entries (IPv4), 256 entries (IPv6)MAC address table size 16384 entries Reliability MTBF (years) 52.79 Environment Operating temperature 32°F to 113°F (0°C to 45°C)Operating relative humidity 10% to 90%, noncondensingNonoperating/Storage temperature -40°F to 158°F (-40°C to 70°C)Nonoperating/Storage relative humidity 5% to 95%, noncondensingAcoustic Low-speed fan: 47.1 dB, High-speed fan: 50.7 dB; ISO 7779 Electrical characteristics Frequency 50/60 HzMaximum heat dissipation 102/204 BTU/hr (107.61/215.22 kJ/hr), for AC Powered units. For DC powered units heat dissipation is 130BTU/hr min, 232BTU/hr max.AC voltage 100 - 240 VACDC voltage -48 to -60 VDCCurrent 5 AMaximum power rating 60 WIdle power 30 W Notes Idle power is the actual power consumption of the device with no ports connected.Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.Power Ratings for AC Power Suppply indicated above.For DC input power, Idle Power is 38W and Max is 68W.DC Max input current is 8A. Units are supplied without a power supply. Customer must buy 1 or 2 JD362A(AC) or JD366A (DC) power supply. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance Emissions EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A Immunity Generic EN 55024ESD EN300 386 Management IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager Services Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office. (tonerpartner.cz)
Podobné produkty ako HPE FlexNetwork 5130 24G SFP 4SFP+ EI Switch (Must select min 1 power supply) RENEW JG933AR , Tenda teg1050f gigabit switch with sfp (teg1050f)HPE FlexNetwork 5130 24G 4SFP+ 1-slot HI Switch (Must select min 1 power supply) JH323A RENEW (tonerpartner.cz)
Podobné produkty ako HPE FlexNetwork 5130 24G 4SFP+ 1-slot HI Switch (Must select min 1 power supply jd362B) JH323A RENEW , Tenda teg1024f gigabit fanless rackmount switch + sfp (teg1024f)I/O ports and slots 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions17.32(w) x 6.3(d) x 1.72(h) in (44 x 16 x 4.36 cm) (1U height)Weight11.02 lb (5 kg) Memory and processor 1 GB SDRAM, 128 MB flash; packet buffer size: 1.5 MB Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance 1000 Mb Latency< 5 µs10 Gbps Latency< 1.5 µsThroughput 96 MppsRouting/Switching capacity 128 GbpsRouting table size 512 entries (IPv4), 256 entries (IPv6)MAC address table size 16384 entries Reliability MTBF (years) 98.1 Environment Operating temperature 32°F to 113°F (0°C to 45°C)Operating relative humidity 10% to 90%, noncondensingNonoperating/Storage temperature -40°F to 158°F (-40°C to 70°C)Nonoperating/Storage relative humidity 5% to 95%, noncondensingAcoustic High-speed fan: 39.7 dB; ISO 7779 Electrical characteristics Frequency 50/60 HzMaximum heat dissipation 64/88 BTU/hr (67.52/92.84 kJ/hr)AC voltage 100-240 VACCurrent 2 AMaximum power rating 26 WIdle power 19 W Notes Idle power is the actual power consumption of the device with no ports connected.Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance Emissions EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A Immunity Generic EN 55024ESD EN300 386 Management IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager Services Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office. HPE FlexNetwork 5130 24G 4SFP+ EI Switch (JG932A) I/O ports and slots 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions 17.32(w) x 6.3(d) x 1.72(h) in (44 x 16 x 4.36 cm) (1U height) Weight 11.02 lb (5 kg) Memory and processor 1 GB SDRAM, 512 MB flash; packet buffer size: 1.5 MB Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance IPv6 Ready Certified 1000 Mb Latency < 5 µs 10 Gbps Latency < 3 µs Throughput 96 Mpps Routing/Switching capacity 128 Gbps Routing table size 512 entries (IPv4), 256 entries (IPv6) MAC address table size 16384 entries Environment Operating temperature 23°F to 113°F (-5°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Non-operating/Storage temperature -40°F to 158°F (-40°C to 70°C) Non-operating/Storage relative humidity 5% to 95%, noncondensing Acoustic High-speed fan: 39.7 dB; ISO 7779 Electrical characteristics Frequency 50/60 Hz Maximum heat dissipation 64/88 BTU/hr (67.52/92.84 kJ/hr) Voltage 100 - 240 VAC, rated Current 2 A Maximum power rating 26 W Idle power 19 W Notes - Idle power is the actual power consumption of the device with no ports connected. - Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance Emissions EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A Immunity Generic EN 55024 ESD EN300 386 Management IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager Services Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. (tonerpartner.cz)
Podobné produkty ako HPE FlexNetwork 5130 24G 4SFP+ EI Switch HP RENEW JG932A , Microsoft surface 127w power supply (us7-00019)HPE FlexNetwork 5140 24G PoE+ 4SFP+ EI Switch JL827A RENEWThe HPE FlexNetwork 5140 EI Switch Series comprises Gigabit Ethernet switches that support static, OSPF and RIP Layer 3 routing, convenient fixed 10GbE uplink ports, PoE+, ACLs, IPv6 and delivers energy savings with Energy Efficient Ethernet. Unique Intelligent Resilient Fabric (IRF) technology creates a virtual fabric by managing several switches as one logical device, which increases network resilience, performance, and availability, while reducing operational complexity. These switches provide Gigabit Ethernet access and can be used at the edge of a network or to connect server clusters in small data centers. High availability, simplified management, and comprehensive security control policies are among the key features that distinguish this series. HPE FlexNetwork 5140 48G 4SFP+ EI Switch (JL829A) I/O ports and slots 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions 17.32(w) x 9.04(d) x 1.72(h) in (44 x 23 x 4.36 cm) (1U height) Weight 7.72 lb (3.5 kg) Memory and processor 512 MB SDRAM, 256 MB flash Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (Rack Mount Kit R8M91A sold separately) Performance IPv6 Ready Certified 1000 Mb Latency < 5 µs 10 Gbps Latency < 3 µs Throughput 131 Mpps Routing/Switching capacity 176 Gbps Routing table size 1024 entries MAC address table size 16384 entries Environment Operating temperature 23°F to 113°F (-5°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Non-operating/Storage temperature -40°F to 158°F (-40°C to 70°C) Non-operating/Storage relative humidity 5% to 95%, noncondensing Acoustic Low-speed fan: 42.2 dB, High-speed fan: 49.3 dB; ISO 7779 Electrical characteristics Frequency 50/60 Hz Maximum heat dissipation 130/153 BTU/hr (137.15/161.42 kJ/hr), For AC powered units. For DC powered units heat dissipation is 130 BTU/hr min, 171 BTU/hr max Voltage 100 - 240 VAC -48 to -60 VDC Current 10 A Maximum power rating 44 W Idle power 38 W Notes: - Idle power is the actual power consumption of the device with no ports connected. - Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. - Power ratings for AC power indicated above. Current used is 5A Max when DC Power used. For DC input power, idle power is 38W, maximum DC power used is 50W. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; IEC 62368-1; CAN/CSA-C22.2 No. 60950-1; EN 62368-1/A11; FDA 21 CFR Subchapter J; ROHS Compliance Emissions FCC Part 15 Subpart B CLASS A; ICES-003 CLASS A; VCCI-CISPR 32 CLASS A; EN 55032 CLASS; AS/NZS CISPR32 CLASS A; CISPR 24; EN 55024; EN 61000-3-2; EN 61000-3-3; ETSI EN 300 386; GB/T 9254; YD/T 993 Immunity Generic EN 55024 ESD EN300 386 Management IMC - Intelligent Management Center; SmartMC; command-line interface; Web browser; SNMP Manager Services Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. HPE FlexNetwork 5140 24G PoE+ 4SFP+ (370W) EI Switch (JL827A ) I/O ports and slots 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T) with 4 combo ports (RJ-45 or SFP); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions 17.32(w) x 10.24(d) x 1.72(h) in (44 x 26 x 4.36 cm) (1U height) Weight 17.64 lb (8 kg) Memory and processor 512 MB SDRAM, 256 MB flash Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (Rack Mount Kit R8M91A sold separately) Performance IPv6 Ready Certified 1000 Mb Latency < 5 µs 10 Gbps Latency < 3 µs Throughput 95 Mpps Routing/Switching capacity 128 Gbps Routing table size 1024 entries MAC address table size 16384 entries Environment Operating temperature 23°F to 113°F (-5°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Non-operating/Storage temperature -40°F to 158°F (-40°C to 70°C) Non-operating/Storage relative humidity 5% to 95%, noncondensing Acoustic Low-speed fan: 44.4 dB, High-speed fan: 53.6 dB; ISO 7779 Electrical characteristics Frequency 50/60 Hz Maximum heat dissipation 102/1569 BTU/hr (107.61/1655.29 kJ/hr), for AC Power. For DC Power min heat dissipation is 85 BTU/hr and max heat dissipation is 2695 BTU/hr Voltage 100 - 240 VAC, -54 to -57 VDC Current 10 A Maximum power rating 451 W Idle power 30 W PoE power 370 W PoE+ Notes: - Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. PoE Power is the power supplied by the internal power supply. When supplemented with the use of an HPE RPS1600 Redundant Power System, up to 740 W of PoE+ can be supplied. - Max current rating for DC power is 25A. AC Input power is 30W typical, and 460W max(including 370W PoE+ consumption. DC Input voltage range is -54 to -57VDC. Total DC input power is 25W Typical and 790W with 740W PoE+ Power consumption. DC Input voltage range is -54VDC to -57VDC. DC Input Source is the HPE RPS1600. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; IEC 62368-1; CAN/CSA-C22.2 No. 60950-1; EN 62368-1/A11; FDA 21 CFR Subchapter J; ROHS Compliance Emissions FCC Part 15 Subpart CLASS A; ICES-003 CLASS A; VCCI-CISPR 32 CLASS A; EN 55032 CLASS; AS/NZS CISPR32 CLASS A; CISPR 24; EN 55024; EN 61000-3-2; EN 61000-3-3; ETSI EN 300 386; GB/T 9254; YD/T 993 Immunity Generic EN 55024 ESD EN300 386 Management IMC - Intelligent Management Center; SmartMC; command-line interface; Web browser; SNMP Manager. Services Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. Models HPE FlexNetwork 5140 24G POE+2SFP+2XGT EI Switch JL823A HPE FlexNetwork 5140 48G PoE+ 4SFP+ EI Switch JL824A HPE FlexNetwork 5140 48G POE+ 2SFP+ 2XGT EI Switch JL825A HPE FlexNetwork 5140 24G SFP w/8G Combo 4SFP+ EI Switch JL826A HPE FlexNetwork 5140 24G PoE+ 4SFP+ EI Switch JL827A HPE FlexNetwork 5140 24G 4SFP+ EI Switch JL828A HPE FlexNetwork 5140 48G 4SFP+ EI Switch JL829A HPE FlexNetwork 5140 24G 2SFP+ 2XGT EI Switch R8J41A HPE FlexNetwork 5140 8G 2SFP 2GT Combo EI Switch R8J42A Key features Gigabit Ethernet access switch with static layer 3 routing, RIP, high density 10GbE uplinks and POE+ models for voice, video and wireless IRF technology that enables plug-and-play device aggregation and link aggregation across multiple devices Embedded network management capabilities at no additional cost with Smart Management Centre (SmartMC) Energy-saving green design features such as automatic switching of idle ports to energy-saving mode and powering down unused ports Standard Features Software-defined networking OpenFlow Supports OpenFlow 1.3 specification to enable SDN by allowing separation of the data (packet forwarding) and control (routing decision) paths Quality of Service (QoS) Broadcast control Allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic Advanced classifier-based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority level and rate limit to selected traffic on a port, VLAN, or whole switch Powerful QoS feature Supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR), and SP+WRR Traffic policing Supports Committed Access Rate (CAR) and line rate Connectivity Auto-MDIX Automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports Flow control Provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations High-density connectivity Provides up to 48 fixed 10/100/1000BASE-T ports in a Layer 2/Layer 3 switch IEEE 802.3at Power over Ethernet (PoE+) support Simplifies deployment and dramatically reduces installation costs by helping to eliminate the time and cost involved in supplying local power at each access point location Ethernet operations, administration and maintenance (OAM) Detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the status of the link between two devices Resiliency and high availability Separate data and control paths Separate control from services and keeps service processing isolated; increases security and performance External redundant power supply Provides high reliability Smart link Allows 100 ms failover between links Spanning Tree/MSTP, RSTP, PVST+, RPVST+ Link redundancy with support for protocols such as Multiple Spanning Tree Protocol (MSTP), Rapid Spanning Tree Protocol (RSTP), Per-VLAN Spanning Tree (PVST+), Rapid Per-VLAN Spanning Tree (RPVST+), Equal-Cost Multipath (ECMP), and Smart Link provides high availability Intelligent Resilient Fabric (IRF) Creates virtual resilient switching fabrics, where two or more switches perform as a single L2 switch and L3 router; switches do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached using standard LACP for automatic load balancing and high availability; can eliminate the need for complex protocols like Spanning Tree Protocol, (), or VRRP, thereby simplifying network operation Layer 3 routing Static IP routing Provides manually configured routing for both IPv4 and IPv6 networks Open Shortest Path First (OSPF) An Interior Gateway Protocol (IGP) that uses a link state routing algorithm; supports OSPFv1/v2 and OSPFv3 Routing Information Protocol (RIP) Uses a distance vector algorithm with UDP packets for route determination; supports RIPv1 and RIPv2 routing; includes loop protection Management Remote configuration and management Enables configuration and management through a secure Web browser or a CLI located on a remote device Manager and operator privilege levels Provides read-only (operator) and read/write (manager) access on CLI and Web browser management interfaces Command authorization Leverages HWTACACS to link a custom list of CLI commands to an individual network administrator's login; also provides an audit trail Secure Web GUI Provides a secure, easy-to-use graphical interface for configuring the module via HTTPS Multiple configuration files Stores easily to the flash image Complete session logging Provides detailed information for problem identification and resolution Remote monitoring (RMON) Uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a private alarm extension group IEEE 802.1AB Link Layer Discovery Protocol (LLDP) Advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network management applications sFlow (RFC 3176) Provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and real-time network monitoring purposes Management VLAN Segments traffic to and from management interfaces, includingCLI/telnet, a Web browser interface, and SNMP Remote intelligent mirroring Mirrors ingress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the network Device Link Detection Protocol (DLDP) Monitors a cable between two compatible switches and shuts down the ports on both ends if the cable is broken, which prevents network problems such as loops IPv6 management Provides future-proof networking because the switch is capable of being managed whether the attached network is running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, syslogv6, FTPv6, SNMPv6, DHCPv6, and RADIUS for IPv6 Troubleshooting Ingress and egress port monitoring enables network problem-solving; virtual cable tests provide visibility into cable problems Smart Management Center (SmartMC) Embedded network management tool with a web-based GUI to simplify operations and facilitate centralized management. It is made available at no additional cost and offers centralized configuration backup, software version management and seamless switch replacement. HPE Intelligent Management Center (IMC) Integrates fault management, element configuration, and network monitoring from a central vantage point; built-in support for third-party devices enables network administrators to centrally manage all network elements with a variety of automated tasks, including discovery, categorization, baseline configurations, and software images; the software also provides configuration comparison tools, version tracking, change alerts, and more Network Management SNMP v1/v2c/v3, MIB-II with Traps, and RADIUS Authentication Client MIB (RFC 2618); embedded HTML management tool with secure access Security Access control lists (ACLs) Provides IP Layer 2 to Layer 4 traffic filtering; supports global ACL, VLAN ACL, port ACL, and IPv6 ACL IEEE 802.1X Industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server MAC-based authentication Client is authenticated with the RADIUS server based on the client's MAC address Identity-driven security and access control - Per-user ACLs Permits or denies user access to specific network resources based on user identity and time of day, allowing multiple types of users on the same network to access specific network services without risking network security or providing unauthorized access to sensitive data - Automatic VLAN assignment Automatically assigns users to the appropriate VLAN based on their identities Secure management access Delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, HTTPS and/or SNMPv3 Secure FTP/ SCP Allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch configuration file Guest VLAN Provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X Port security Allows access only to specified MAC addresses, which can be learned or specified by the administrator Port isolation Secures and adds privacy, and prevents malicious attackers from obtaining user information STP BPDU port protection Blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks STP root guard Protects the root bridge from malicious attacks or configuration mistakes DHCP protection Blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks IP source guard Helps prevent IP spoofing attacks Dynamic ARP protection Blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data RADIUS/HWTACACS Eases switch management security administration by using a password authentication server Performance Nonblocking architecture Up to 176 Gb/s nonblocking switching fabric provides wirespeed switching with up to 130.9 Mpps throughput Hardware-based wirespeed access control lists (ACLs) Help provide high levels of security and ease of administration without impacting network performance with a feature-rich TCAM-based ACL implementation Device support Prestandard PoE Support Detects and provides power to prestandard PoE devices such as wireless LAN access points and IP phones Convergence IEEE 802.1AB Link Layer Discovery Protocol (LLDP) Facilitates easy mapping using network management applications with LLDP automated device discovery protocol LLDP-MED Is a standard extension that automatically configures network devices, including LLDP-capable IP phones LLDP-CDP compatibility Receives and recognizes CDP packets from Cisco's IP phones for seamless interoperation IEEE 802.3at Power over Ethernet (PoE+) Provides up to 30 W per port that allows support of the latest PoE+-capable devices such as IP phones, wireless access points, and security cameras, as well as any IEEE 802.3af-compliant end device; eliminates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments PoE allocations Supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to allocate PoE power for more efficient energy savings Voice VLAN Automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance IP multicast snooping (data-driven IGMP) Prevents flooding of IP multicast traffic Additional information Green IT and power Improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and utilizes variable-speed fans, reducing energy costs Green initiative support Provides support for RoHS and WEEE regulations Unified Hewlett Packard Enterprise Comware operating system with modular architecture Provides an easy-to-enhance-and-extend feature set, which doesn't require whole-scale changes; all switching, routing, and security platforms leverage the Comware OS, a common unified modular operating system Energy Efficient Ethernet (EEE) Support Reduces power consumption in accordance with IEEE 802.3az Layer 2 switching 16K MAC address table Provides access to many Layer 2 devices VLAN support and tagging Supports IEEE 802.1Q with 4,094 simultaneous VLAN IDs IEEE 802.1ad QinQ and selective QinQ Increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a high-speed campus or metro network 10GbE port aggregation Allows grouping of ports to increase overall data throughput to a remote device Device Link Detection Protocol (DLDP) Monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STP-based networks Jumbo Frame Support Improves the performance of large data transfers; supports frame size of up to 9K-bytes Layer 3 services Address Resolution Protocol (ARP) Determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a Layer 2 network Dynamic Host Configuration Protocol (DHCP) Simplifies the management of large IP networks; supports client; DHCP Relay enables DHCP operation across subnets Loopback interface address Defines an address that can always be reachable, improving diagnostic capability User Datagram Protocol (UDP) helper function Allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents server spoofing for UDP services such as DHCP Route maps Provide more control during route redistribution; allow filtering and altering of route metrics DHCP server Centralizes and reduces the cost of IPv4 address management Warranty and support Limited Lifetime Warranty See Warranty check for warranty and support information included with your product purchase. Software releases To find software for your product, refer to http://www.hpe.com/networking/support; for details on the software releases available with your product purchase, refer to Warranty check (tonerpartner.cz)
Podobné produkty ako HPE FlexNetwork 5140 24G PoE+ 4SFP+ EI Switch JL827A RENEW , Microsoft surface 65w power supply (q4q-00017)HP 5130-48G-4SFP+ EI Switch HP RENEW 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ fixed 1000/10000 SFP+ ports (tonerpartner.cz)
Podobné produkty ako HPE 5130-48G-4SFP+ EI HP RENEW Switch JG934AR , Vřeteno osudu (978-80-747-5130-1)HPE Aruba Networking CX 6000 24G 4SFP Switch R8N88A RENEW Model Aruba 6000 24G 4SFP Switch (R8N88A) Description 24x ports 10/100/1000BASE-T Ports 4x 1G SFP ports 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply Fans Fixed fans Dimensions (H) 4.39 cm (W) 44.2 cm (D) 20.12 cm (1.73" x 17.4" x 7.92") Configuration Weight 2.62 kg (5.78 lbs) CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Model Switching Capacity 56 Gbps Model Throughput Capacity 41.6 Mpps Average Latency (LIFO-64-bytes packets) 1 Gbps: 1.5 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.9 Bel Sound Pressure, LpAm (Bystander) = 20.9 dB Primary Airflow Side-to-side Aruba 6000 24G 4SFP Switch (R8N88A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6000 24G 4SFP Switch R8N88A RENEW , Cudy 8-port gigabit industrial switch with 2 gigabit sfp port (ig1008s2)HPE Aruba Networking CX 6100 24G 4SFP+ Switch JL678A RENEW Aruba 6100 24G 4SFP+ Switch (JL678A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting Standards And Protocols (Applies to all products in series) RFC 1591 DNS (client) SSHv1/SSHv2 Secure Shell IEEE 802.1D MAC Bridges IEEE 802.1p Priority IEEE 802.1Q VLANs IEEE 802.1s Multiple Spanning Trees IEEE 802.1w Rapid Reconfiguration of Spanning Tree IEEE 802.3 Type 10BASE-T IEEE 802.3ab 1000BASE-T IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.3at Power over Ethernet IEEE 802.3az Energy Efficient Ethernet IEEE 802.3x Flow Control RFC 768 UDP RFC 783 TFTP Protocol (revision 2) RFC 792 ICMP RFC 793 TCP RFC 826 ARP RFC 1350 TFTP Protocol (revision 2) RFC 2131 DHCP client RFC 4330 Simple Network Time Protocol (SNTP) v4 RFC 951 BOOTP (VLAN 1 Only) RFC 1542 BOOTP Extensions (VLAN 1 only) IGMPv2/IGMPv3 IGMP/MLD Snooping RFC 1981 IPv6 Path MTU Discovery RFC 2460 IPv6 Specification RFC 2925 Remote Operations MIB (Ping only) RFC 3315 DHCPv6 (client only) RFC 3513 IPv6 Addressing Architecture RFC 3596 DNS Extension for IPv6 RFC 3176 sFlow RFC 4022 MIB for TCP RFC 4113 MIB for UDP (Partially) RFC 4251 SSHv6 Architecture RFC 4252 SSHv6 Authentication RFC 4253 SSHv6 Transport Layer RFC 4254 SSHv6 Connection RFC 4293 MIB for IP RFC 4419 Key Exchange for SSH RFC 4443 ICMPv6 RFC 4861 IPv6 Neighbor Discovery RFC 4862 IPv6 Stateless Address Auto-configuration RFC 1213 MIB RFC 1493 Bridge MIB RFC 2674 802.1p and IEEE 802.1Q Bridge MIB (Partial support. MIB objects supported: ieee8021BridgeBasePort, ieee8021BridgeBasePort, ieee8021BridgePortMrpJoinTime, ieee8021BridgePortMrpLeaveTime, ieee8021BridgePortMrpLeaveAllTime) RFC 2737 Entity MIB RFC 2863 The Interfaces Group MIB IEEE 802.1AB Link Layer Discovery Protocol (LLDP) RFC 1098 A Simple Network Management Protocol (SNMP) ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED) SNMPv1/v2c/v3 RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events) RFC 1098 A Simple Network Management Protocol (SNMP) RFC 2474 DiffServ precedence, with 2/4/8 queues per port RFC 2475 DiffServ Architecture RFC 2597 DiffServ Assured Forwarding (AF) RFC 2598 DiffServ Expedited Forwarding (EF) IEEE 802.1X Port Based Network Access Control RFC 1492 TACACS+ RFC 2138 RADIUS Authentication RFC 2866 RADIUS Accounting Secure Sockets Layer (SSL) (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6100 24G 4SFP+ Switch JL678A RENEW , Cudy 24-port gigabit poe+ switch with 2 sfp ports 300w (gs1028ps2)Aruba 6000 24G Class4 PoE 4SFP 370W Switch RENEW R8N87A EAN: 726316 Specifikace Porty: 24x 10/100/1000BASE-T Ports SFP porty: 4x 1G/10G PoE: Podporuje IEEE 802.3af, 802.3at USB porty: 1x USB-C Console Port, 1x USB Type-A Host port Zdroj energie a fyzické vlastnosti Zdroj energie: Pevný, až 370W třídy 4 PoE Ventilátory: Pevné Rozměry: 4.39 cm (V) x 44.2 cm (Š) x 26.82 cm (H) Hmotnost: 4.19 kg Technické parametry Procesor: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť: 4 GB DDR3, 16 GB eMMC Packet Buffer: 12.38MB Kapacita přepínání: 56 Gbps Průchodová kapacita: 41.6 Mpps Prostředí Provozní teplota: 0°C do 45°C Relativní vlhkost při provozu: 15% až 95% při 40°C Maximální provozní výška: 3000 metrů Elektrické vlastnosti Frekvence: 50 / 60 Hz AC napětí: 100-127 VAC / 200-240 VAC Proud: 4.6 A / 2.3 A Bezpečnost a certifikace Bezpečnost: UL 60950-1; IEC 60950-1; EN 60950-1 Emise: VCCI-CISPR 32, Class A Montáž a skříň Montuje se do standardního 19-palcového telco racku nebo skříně pro zařízení (k dispozici montážní sada); montáž na vodorovnou plochu; montáž na stěnu. (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6000 24G Class4 PoE 4SFP 370W Switch RENEW R8N87A , Cudy 4-port gigabit industrial switch with 2 gigabit sfp port (ig1004s2)Aruba 6200F 24G 4SFP+ Switch JL724A RENEW Klíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE a až 370 W PoE třídy 4 pro podporu zařízení IoT. Inteligentní monitorování, přehled a řešení problémů s nástrojem Aruba Network Analytics Engine. Jednoduché nasazení jedním dotykem pomocí Aruba CX mobilní aplikací. Zabezpečený a jednoduchý přístup pro uživatele a IoT s technologií Aruba Dynamic Segmentation. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti. (tonerpartner.cz)
Podobné produkty ako Aruba 6200F 24G 4SFP+ Switch JL724A RENEW , Cudy 4-port gigabit industrial poe switch with 2 gigabit sfp port (ig1004s2p)Aruba Instant On 1930 24G 4SFP/SFP+ Switch EAN: 190017355450 Aruba Instant On 1930 24G 4SFP/SFP+ Switch je výkonný switch navržený pro malé podniky. Fyzické vlastnosti Switch má rozměry 17.42(w) x 8.72(d) x 1.73(h) palce a váží 2.41 kg. Výkon S ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM a 256 MB flash dosahuje propustnost 95.23 Mpps a kapacitu 128 Gbps. Spolehlivost MTBF je 158 let. Prostředí Pracuje v teplotách od 0°C do 40°C a vlhkosti 15% až 95% při 40°C. Elektrické vlastnosti Frekvence: 50-60 Hz, napětí: 100-240V, proud: 0.5/0.3 A, maximální výkon: 22.6 W, klidový výkon: 9.3 W. Bezpečnost Switch je certifikovaný dle standardů UL 60950-1, IEC 60950-1,EN 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60825-1 a dalších. Správa zařízení Aruba Instant On Cloud; Web browser; SNMP Manager Montáž Montuje se do standardu EIA 19 in. telco rack nebo do skříně. Podporuje také stolní, stěnovou a podstolní montáž. Klíčové vlastnosti Chytrý spravovaný switch s vrstvou 2+ PoE pro napájení AP a IoT zařízení Bezpečnostní ovládání pro definování přístupu v síti Pohodlná mobilní aplikace a webové rozhraní pro nastavení a správu Standardní funkce Plug-and-play switchy, které fungují s AP Instant On hned po vybalení Mobilní aplikace pro snadné nastavení, sledování a správu sítě Automatická ochrana před DoS útoky Bez dodatečných licenčních nebo předplatných poplatků Průmyslově nejlepší omezená doživotní záruka a podpora Management Cloudové řízení celé sítě, jednoduché lokální webové GUI řízení, podpora až pěti (5) HTTP a HTTP Secure (HTTPS) relací. Kvalita služby (QoS) Prioritizace provozu, IEEE 802.1p/Q VLAN značení, třída služby (CoS), pokročilý klasifikátor na základě QoS. Bezpečnost sítě TPM-based security, IEEE 802.1Q VLAN support, IEEE 802.1X access control, automatická ochrana před DoS útoky, ochrana před bouří paketů, RADIUS, RADIUS účetnictví, Management VLAN ID, prevence proti Link Flap. Výkon a efektivita Energy Efficient Ethernet (EEE), automatické vypnutí portu, stav úspory energie, energeticky účinné chlazení, bezventilátorový provoz. Switchingové funkce IEEE 802.3x Flow control, Spanning Tree Protocol (STP), ochrana proti smyčkám, BPDU filtrování, podpora Jumbo frame, IGMP snooping v1/v2, Link agregace, LLDP/LLDP-MED (Media Endpoint Discovery), Address Resolution Protocol (ARP). Záruka, servis a podpora Aruba Instant On Limited Lifetime Support poskytuje 24X7 telefonickou podporu po prvních 90 dnech a chatovou podporu po celou dobu záruky. Komunitní podpora je zahrnuta po dobu života produktu. (tonerpartner.cz)
Podobné produkty ako Aruba Instant On 1930 24G 4SFP/SFP+ Switch , Cudy 16-port 10/100m poe+ switch with 1gigabit uplink and 1 gigabit combo sfp port 200w (fs1018ps1 )Aruba 6000 48G 4SFP Switch R8N86AR RENEW EAN: 726354 Zvyšte výkon sítě s Aruba 6000 48G 4SFP Switch. Tento přepínač je ideální pro náročné sítě. Specifikace portů Přepínač Aruba 6000 48G 4SFP je vybaven 48x porty 10/100/1000BASE-T a 4x 1G/1G SFP porty. Dále obsahuje 1x USB-C Console Port a 1x USB Type-A Host port pro snadné připojení a správu. Dimenze a hmotnost Aruba 6000 48G 4SFP má rozměry 4.39 cm x 44.2 cm x 24.74 cm a váží 3.42 kg. Je kompaktní a lehký pro snadnou instalaci a přenos. Výkon a kapacita Přepínač má dvojjádrový procesor ARM Cortex A9 s frekvencí 1016 Mhz, 4 GB DDR3 paměť a 16 GB eMMC flash paměť. Jeho přepínací kapacita je 104 Gbps a propustnost 77.3 Mpps. Bezpečnost a regulace Aruba 6000 48G 4SFP splňuje bezpečnostní standardy UL 60950-1, IEC 60950-1, EN 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60825-1, UL 62368-1 Ed. 2, IEC 62368-1 Ed. 2, EN 62368-1:2014. Provozní podmínky Aruba 6000 48G 4SFP může pracovat v teplotách od 0°C do 45°C a relativní vlhkosti od 15% do 95% při teplotě 40°C. Elektrické charakteristiky Přepínač pracuje na frekvenci 50/60 Hz, napětí 100-127 VAC / 200-240 VAC a proud 0.8 A / 0.5 A. Spotřeba energie v klidu je 20.6W a maximální spotřeba (bez PoE) je 44.2W. Klíčové vlastnosti 48x porty 10/100/1000BASE-T 4x 1G/1G SFP porty USB-C Console Port a USB Type-A Host port Dvojjádrový procesor ARM Cortex A9 s frekvencí 1016 Mhz 4 GB DDR3 paměť a 16 GB eMMC flash paměť Přepínací kapacita 104 Gbps a propustnost 77.3 Mpps Dodáváme s pevnými napájecími zdroji a pevnými ventilátory pro bezproblémový provoz. Aruba 6000 48G 4SFP je ideální pro náročné sítě vyžadující vysoký výkon a spolehlivost. (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6000 48G 4SFP Switch R8N86AR RENEW , 1 2 switch - nintendo switch (045496420185)Aruba 6100 48G 4SFP+ Switch RENEW full warr JL676A Klíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE. Kompaktní 12portový model bez ventilátoru pro tichý chod. Flexibilita správy s podporou Aruba Central, snadno použitelné webové grafické rozhraní, rozhraní CLI a Aruba NetEdit. Jednoduché nasazení s funkcí Zero Touch Provisioning. Připravenost na softwarovou definici s rozhraními REST API. Zjednodušení přidávání, přesunů a změn pomocí bezbarvého systému portů. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti. Specifications Aruba 6100 48G 4SFP+ Switch (JL676A) Description 48x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (65W) Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 24.74 cm (1.73" x 17.4" x 9.74") Configuration Weight 3.42 kg (7.54 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 176 Gbps Model Throughput Capacity 98.6 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.9 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 48G 4SFP+ Switch (JL676A) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.6 Bel Sound Pressure, LpAm (Bystander)= 24.6 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.8 A / 0.5 A Power Consumption (230 VAC) Idle: 20.6W Max Power (w/o PoE): 44.2W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 48G 4SFP+ Switch (JL676A) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6100 48G 4SFP+ Switch RENEW JL676A , Hp desktop 65w mini power supply kit (l2x04aa#abb)Aruba 6000 24G Class4 PoE 4SFP 370W Switch Popis Aruba 6000 24G Class4 PoE 4SFP 370W Switch je vysoce výkonný přepínač s 24 porty 10/100/1000BASE-T a 4 porty 1G/10G SFP. Specifikace Porty: 24x 10/100/1000BASE-T, 4x 1G/10G SFP Podpora PoE: Ano, standardy IEEE 802.3af, 802.3at USB porty: 1x USB-C Console Port, 1x USB Type-A Host port Napájení: Pevný zdroj, až 370W Class 4 PoE Power Ventilátory: Pevné Technické parametry Procesor: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť: 4 GB DDR3, 16 GB eMMC Buffer: 12.38MB (4.5MB Ingress/7.875MB Egress) Rozměry: (H) 4.39 cm (W) 44.2 cm (D) 26.82 cm Hmotnost: 4.19kg Výkon Přepínací kapacita: 56 Gbps Průchodnost: 41.6 Mpps Průměrná latence: 1 Gbps: 1.5 µSec Prostředí Pracovní teplota: 32°F to 113°F (0°C to 45°C) Vlhkost: 15% to 95% at 104°F (40°C) non-condensing Max výška: 10000 feet (3 km) Max Elektrické charakteristiky Frekvence: 50 / 60 Hz Napětí: 100-127 VAC / 200-240 VAC Proud: 4.6 A / 2.3 A Spotřeba: Idle: 22.9W, Max Power (w/o PoE): 32.7W, Max Power (w/ PoE): 455W Bezpečnost a certifikace Aruba 6000 24G Class4 PoE 4SFP 370W Switch splňuje bezpečnostní standardy UL 60950-1, IEC 60950-1, EN 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60825-1, UL 62368-1 Ed. 2, IEC 62368-1 Ed. 2, EN 62368-1:2014. Montáž Aruba 6000 24G Class4 PoE 4SFP 370W Switch lze montovat do standardního 19-palcového telekomunikačního racku nebo skříně (k dispozici je montážní sada), na horizontální povrch nebo na zeď. (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6000 24G Class4 PoE 4SFP 370W Switch , Tetra min 1 l (4004218708914)Řada přepínačů Aruba CX 6100 je moderní rodina přístupových přepínačů základní úrovně ideální pro pobočky, střední podniky a sítě SMB. Přepínače Aruba CX 6100, navržené pro spolehlivý, jednoduchý a bezpečný přístup, poskytují pohodlné řešení kabelového přístupu pro podnikové sítě podporující IoT, mobilní a cloudové aplikace. Technické parametry 24x 10/100/1000Base-T porty 4x 1/10G SFP porty 1x USB-C Console Port, 1x USB Type-A Host port Interní (pevný) napájecí zdroj (500 W), pevné ventilátory Maximální výkon: 32,7 W bez PoE, 455 W s PoE Vstupní napětí: 100-127 VAC / 200-240 VAC Přepínací kapacita: 128 Gb/s Propustnost: 95,2 Mpps Procesor: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť a Flash: 4 GB DDR3, 16 GB eMMC Možnost PoE: Až 370W Class 4 PoE Rozměry: 4,39 x 44,2 x 26,82 cm Hmotnost: 4,2 kg Specifications Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch (JL677A) Description 24x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports Supports PoE Standards IEEE 802.3af, 802.3at 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (500W) Up to 370W of Class 4 PoE Power Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 26.82 cm (1.73" x 17.4" x 10.56") Configuration Weight 4.19kg (9.24 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 128 Gbps Model Throughput Capacity 95.2 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.5 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch (JL677A) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.9 Bel Sound Pressure, LpAm (Bystander)= 24.3 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 4.6 A / 2.3 A Power Consumption (230 VAC) Idle: 22.9W Max Power (w/o PoE): 32.7W Max Power (w/ PoE): 455W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch (JL677A) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (tonerpartner.cz)
Podobné produkty ako Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch JL677AR RENEW , Hpe ml30 gen10+ (p44718-421)High-Performance, Smart-Managed Switches Designed with Small Businesses in Mind Whether you own a cafe, a design firm or a tech startup, a reliable and secure network plays a critical role in the success of your business. And you need a network solution that gives you peace of mind, allowing you to focus on growing your business instead of managing problems with your network. Aruba Instant On makes it easy to keep network users happy, mobile and IoT devices connected, and your network secure. The Aruba Instant On 1930 switches features advanced, smart-managed, fixed- configuration Gigabit switches designed for small businesses that are easy-to-deploy and affordable. They're made to handle today's bandwidth-heavy applications like voice and video conferencing, enabling consistent connectivity to enhance performance. Using either the Instant On mobile app or the cloud-based web portal, you can quickly set up, monitor and manage the 1930 switch series from anywhere at any time. What's more, up to 30 W PoE power delivery is available out-of-the-box for your class 4 PoE devices, like access points, surveillance cameras and VoIP phones, all easily managed from the same platform. Built-in security features protect your network from unauthorized access by allowing you to segment traffic and define access to each area of the network. And all of this is included in the price of the hardware - there are no hidden subscription or licensing fees. Key Features Smart-managed layer 2+ Ethernet switch series ready to deploy in 8-, 24-and 48-port for non-PoE and Class 4 PoE models PoE to power APs and IoT devices like IP phones, surveillance cameras and door locks Two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models to eliminate traffic bottlenecks across your network Security controls let you define access in each area of your network, keeping your business data safe Convenient mobile app and web- based GUI for set up, management and troubleshooting. Standards and Protocols (applies to all products in series) IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3z 1000BASE-X IEEE 802.2af PoE 1 (PoE models only) IEEE 802.3at PoE 1 (PoE models only) IEEE 802.3x Flow control IEEE 802.1Q VLANS IEEE 802.1p Priority IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.1X Port Access Authentication IEEE 802.3az Energy Efficient Ethernet IEEE 802.1D: Spanning Tree Protocol IEEE 802.1W: Rapid Spanning Tree Protocol IEEE 802.1S: Multiple Spanning Tree Protocol IEEE 802.1AB Link Layer Discovery Protocol Denial of service protection CPU DoS protection Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 370W Switch (JL684B) I/O Ports and Slots 24 RJ-45 autosensing 10/100/1000 Class 4 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 10.42(d) x 1.73(h) in (44.25 x 26.47 x 4.39 cm) (1U height) Weight 8.23 lb (3.73 kg) Processor and Memory ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5 MB Memory And Flash 512 MB SDRAM 256 MB flash Packet Buffer 1.5 MB Performance 100 Mb latency < 4.7 uSec 1000 Mb latency 10000 Mb latency Throughput (Mpps) 95.23 Mpps Capacity 128 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 71 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic1 LWAd = 4.0 Bel LpAm (Bystander) = 24 dB Notes: 1Acoustics measured in 23°C semi-anechoic chamber with a loading of 100% traffic and 50% PoE on all ports. Measured in accordance with ISO 7779. Declared in accordance with ECMA-109:2010. Values presented are the Declared A-Weighted Sound Power Level (LWAd) and the mean Bystander A-Weighted Sound Pressure Level (LpAm) Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current 4.9 A/2.4 A Maximum power rating 440.4W Idle power 20.3W PoE power 370 W Class 4 PoE Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) Standard Features Simplicity at Its Best Plug-and-play switches that work together with Instant On APs right out of the box Mobile app to easily setup, monitor and manage your network Security You Can Count On Protect your network from unauthorized access with IEEE 802.1X and VLANs Automatic denial-of-service (DOS) monitors and protects the network against malicious attacks We've Got You Covered No extra licensing or subscription fees Industry-leading limited lifetime warranty and support. The Instant On Differentiators Easy Setup and Management The Aruba Instant On mobile app allows you to set up, manage, and monitor Instant On switches and access points directly from your phone. Within the app, you get guided step-by-step instructions to install Instant On devices to get your network up and running quickly - no technical expertise required. And cloud-based access allows you to access the network from anywhere, at any time. Non-intrusive, Aesthetic Design Aruba Instant On switches are designed to complement the sleek and clean look of the Instant On access points, and to blend discreetly into your site's environment. The 8-port models, as well as the 24- and 48-port non PoE models, are fan-less, making them ideal for quiet office deployments. High Performance with Flexible Options The series consists of four (4) Class 4 PoE switches, and three (3) non-PoE switches including 8- 24- and 48-port Gigabit Ethernet switches. The two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models, ensure high performance and eliminate traffic bottlenecks across the network. Customizable features include basic Layer 2 features like VLANs and link aggregation, as well as advanced features such as Layer 3 IPv4 static routing, ACLs, and Spanning Tree Protocols, and IPv6 Host mode. Optimized User Experience The Aruba Instant On mobile app provides common workflows for Instant On switches and access points making it easier to configure, monitor and manage your network remotely without the need for additional hardware like cloud keys or VPN. You can also update firmware on your Instant On devices directly from the cloud whenever you want, from wherever you are. Site inventory The site inventory feature on the Instant On mobile app shows you all switches and AP's on a single screen, allowing you to quickly identify non-functioning devices and troubleshoot accordingly. Multi-Site Management The cloud-hosted web interface and mobile app make it easy to manage multiple sites, multiple networks, distributed deployments and multi-tenant deployments. Each site is logically separated and has its own configuration, statistics, guest portal, and admin read/write privileges. Built-In Security Built-in security features protect your network from external threats by blocking malware attacks and keeping unauthorized users off the network. Network traffic can be filtered and access restricted based on MAC and IP address. No Hidden Fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry leading limited lifetime warranty are also included, along with chat support for the life of the product. Management Cloud-Based Management for Entire Network The cloud-hosted web interface and mobile app make it easy to manage networks with Instant On APs and Switches. Simple Local Web GUI Management For management of individual switches, the intuitive Web GUI makes management simple, even for non-technical users. Supports up to five (5) HTTP and HTTP Secure (HTTPS) sessions. Firmware Update Provides notification of the latest firmware with the ability to schedule update at a preferred time through Instant On mobile app and cloud-based web portal. Default DHCP Client Mode Allows the switch to be directly connected to a network, enabling plug-and-play operation. In the absence of a DHCP server on the network, the switch falls back to the static address 192.168.1.1. Port Mirroring Enables traffic on a port or VLAN to be simultaneously sent to a network analyzer for monitoring. Event Logging and Alerts Provides detailed information for problem identification and resolution. Account Management Allows administrators to add, modify, delete and transfer management accounts and passwords for secure access to Instant cloud management solution. Locator LED Allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches. Schedule Configuration Global Schedule feature can be applied to time-based ACLs, port or interface shutdown, or PoE power delivery; up to 3 schedules can be configured. PoE scheduling allows user to configure a specific day/time of the week (e.g. business hours) for Instant On switches to supply power to connected devices (e.g. surveillance cameras, access points etc.). Quality of Service (QoS) Traffic Prioritization Provides time-sensitive packets (like VoIP and video) with priority over other traffic based on DSCP or IEEE 802.1p classification. IEEE 802.1p/Q VLAN Tagging Delivers data to devices based on the priority and type of traffic; supports IEEE 802.1Q. Class of Service (CoS) Sets the IEEE 802.1p/DSCP priority to queue mapping (4 queues). Supports strict priority queuing (SP) or weighted round robin (WRR) queuing. SP and WRR queuing can be configured on individual switch ports. Advanced Classifier Based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information. Access Switching SFP/SFP+ Fiber Connectivity Provides fiber connections for uplinks and other connections across longer distances than copper cabling can support. SFP ports are in addition to available copper Ethernet ports, providing a higher total number of available ports. Two (2) SFP 1G ports available on 8-port models and four (4) SFP+ 1G/10G ports on 24-/48 port models. Ethernet Alliance Certified Class 4 PoE (IEEE 802.3at) Provides up to 30 W per port, which allows support of the class 4 PoE capable devices such as video IP phones, wireless access points, and advanced pan/tilt/zoom security cameras, as well as any 15.4 W IEEE 802.3af-compliant end device; mitigates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. Auto-PoE Power Configuration The switch automatically assigns the required power to a port for a PD device based on Link Layer Discovery Protocol (LLDP). PoE Power Allocation Support multiple methods (LLDP-MED automatic, class of PoE, or usage-based) to allocate PoE power for more efficient energy savings. Auto MDI/MDI-X Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports. Network Security TPM-Based Security Includes a Trusted Platform Module (TPM) for secure hardware- based generation and storage of cryptographic keys used for secure connection to the Instant On cloud portal. IEEE 802.1Q VLAN Support Support for up to 256 VLANs with a VLAN ID range of 2-4093. IEEE 802.1X Access Control Authentication of network users on a per port basis prior to permitting network access. Port authentication includes RADIUS assigned VLAN, dynamic VLAN creation, guest VLAN or into an unauthenticated VLAN. Automatic Denial-of-Service Protection Monitors for malicious attacks and protects the network by blocking the attacks. Packet Storm Protection Protects against unknown unicast, broadcast and multicast storms with user-defined thresholds. RADIUS The switch supports RADIUS authentication with primary and backup server configuration. Automatic VLAN Assignment - RADIUS Assigned VLANs Automatically assigns users to the appropriate VLAN based on their identity and location. RADIUS Accounting A robust set of attributes and statistics are available for collecting information from the switch. Management VLAN ID Provides secure management access to administrators in the specified VLAN. Link Flap Prevention Minimizes the network disruption by automatically detecting and disabling ports that experience link flap events. Performance and Efficiency Energy Efficient Ethernet (EEE) Compliant with IEEE 802.3az standard requirements to save energy during periods of low data activity. Auto-Port Shut Down The switch saves power by automatically shutting down power to inactive ports. Power is restored on a port upon link detection. Energy Savings Status The switch provides an estimated cumulative energy savings due to green Ethernet features being enabled. Energy-Efficient Cooling Includes variable speed fans operating only at the speed necessary to maintain operating temperature to reduce excess noise and power consumption. Fan-Less Operation Fan-less design for 8-port models, 24- and 48-port non-PoE models, making the switches ideal for office deployments. Switching Features IEEE 802.3x Flow Control Provides a flow-throttling mechanism propagated through the network to prevent packet loss at a congested node. Spanning Tree Protocol (STP) Supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP on local web). Loop Protection If the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms. BPDU Filtering Drops BPDU packets when STP is enabled globally but disabled on a specific port. Jumbo Frame Support Supports up to 9216 bytes frame size to improve the performance of large data transfers. IGMP Snooping v1/v2 Improves network performance through multicast filtering, instead of flooding traffic on all ports. Link Aggregation Groups together multiple ports up to a maximum of eight (8) ports per trunk automatically using Link Aggregation Control Protocol (LACP), or manually, to form a high-bandwidth connection to the network backbone that helps prevent traffic bottlenecks. The 8-port models support 4 trunks, 24-port models support 8 trunks, and 48-port models support 16 trunks. LLDP/LLDP-MED (Media Endpoint Discovery) Defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN for automatic configuration of network devices such as IP phones. Address Resolution Protocol (ARP) The ARP table displays all of the IP addresses that have been resolved to MAC addresses, either dynamically or through static entry configuration. Additional Features Accessed Through Local Web-Management Interface Top Event Dashboard Provides notifications for critical events and a quick access to the latest log events. Quick Start-Up and VLAN Wizard Enables automatic configuring of the initial settings such IP address, device information, and system time. VLAN wizard can be used for setting up initial VLAN IDs and port membership. Access Control Lists (ACLs) Enables network traffic filtering by creating an ACL, adds rules and matches criteria to an ACL, and applies the ACL to permit or deny on one or more interfaces or a VLAN. Supports for 50 inbound IPv4 and MAC ACLs with up to 480 ACEs. IPv6 Host Enables switches to be managed and deployed at the IPv6 network's edge. Rate Limiting Sets and enforces per-port ingress traffic limits based on percentages or packets per second. Protected Ports Ports in a port isolation group are restricted from forwarding Layer 2 traffic between ports in that group, providing data privacy and security. SCP and TFTP File Transfer Provides different mechanisms for secure file transfer through SCP (Secure Copy Protocol) or TFTP. Dual Image Support Provide independent primary and secondary software images for backup while upgrading. User Account Management Password strength checking and aging feature provides enhanced security to user account administration to the local web management interface. Additionally, user account authentication can now be done via RADIUS to access the web-interface.' Secure Sockets Layer (SSL) Encrypts all HTTP traffic, secures access to the local browser-based management of the switch. SNMPv1, v2c, and v3 Facilitates remote management with SNMP management station that discovers and monitors the switch. Remote Monitoring (RMON) Provides advanced monitoring and reporting capabilities for statistics, history, alarms and events. RMON data is retrieved from the switch through a network management platform over SNMP. Cable Diagnostic Tool Provides the mechanism to detect and report potential cabling issues, such as cable opens or cable shorts on copper links, in addition to providing distance to the fault and total length of cable. Warranty, Service and Support Aruba Instant On Limited Lifetime Support provides 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is included for the life of the product. Refer to the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. (tonerpartner.cz)
Podobné produkty ako Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 370W Switch , Hpe microserver gen10+ (p18584-421)Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 195W Switch (JL683B) I/O Ports and Slots 24 RJ-45 autosensing 10/100/1000 Class 4 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 10.42(d) x 1.73(h) in (44.25 x 26.47 x 4.39 cm)(1U height) Weight 7.69lb (3.49kg) Processor and Memory ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5 MB Packet Buffer 1.5 MB Performance 100 Mb latency < 4.7 uSec 1000 Mb latency 10000 Mb latency Throughput (Mpps) 95.23 Mpps Capacity 128 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 76 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic1 LWAd = 3.9 Bel LpAm (Bystander) = 25 dB Notes: 1Acoustics measured in 23°C semi-anechoic chamber with a loading of 100% traffic and 50% PoE on all ports. Measured in accordance with ISO 7779. Declared in accordance with ECMA-109:2010. Values presented are the Declared A-Weighted Sound Power Level (LWAd) and the mean Bystander A-Weighted Sound Pressure Level (LpAm) Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current 2.8 A/1.4 A Maximum power rating 248.7W Idle power 19.7W PoE power 195 W Class 4 PoE Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) Aruba Instant On 10G SFP+ to SFP+ 1m DAC (R9D19A) Aruba Instant On 10G SFP+ to SFP+ 3m DAC (R9D20A) Aruba Instant On 1930 Switch Series High-Performance, Smart-Managed Switches Designed with Small Businesses in Mind Whether you own a cafe, a design firm or a tech startup, a reliable and secure network plays a critical role in the success of your business. And you need a network solution that gives you peace of mind, allowing you to focus on growing your business instead of managing problems with your network. Aruba Instant On makes it easy to keep network users happy, mobile and IoT devices connected, and your network secure. The Aruba Instant On 1930 switches features advanced, smart-managed, fixed- configuration Gigabit switches designed for small businesses that are easy-to-deploy and affordable. They're made to handle today's bandwidth-heavy applications like voice and video conferencing, enabling consistent connectivity to enhance performance. Using either the Instant On mobile app or the cloud-based web portal, you can quickly set up, monitor and manage the 1930 switch series from anywhere at any time. What's more, up to 30 W PoE power delivery is available out-of-the-box for your class 4 PoE devices, like access points, surveillance cameras and VoIP phones, all easily managed from the same platform. Built-in security features protect your network from unauthorized access by allowing you to segment traffic and define access to each area of the network. And all of this is included in the price of the hardware - there are no hidden subscription or licensing fees. Key Features Smart-managed layer 2+ Ethernet switch series ready to deploy in 8-, 24-and 48-port for non-PoE and Class 4 PoE models PoE to power APs and IoT devices like IP phones, surveillance cameras and door locks Two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models to eliminate traffic bottlenecks across your network Security controls let you define access in each area of your network, keeping your business data safe Convenient mobile app and web- based GUI for set up, management and troubleshooting. Standard Features Simplicity at Its Best Plug-and-play switches that work together with Instant On APs right out of the box Mobile app to easily setup, monitor and manage your network Security You Can Count On Protect your network from unauthorized access with IEEE 802.1X and VLANs Automatic denial-of-service (DOS) monitors and protects the network against malicious attacks We've Got You Covered No extra licensing or subscription fees Industry-leading limited lifetime warranty and support. The Instant On Differentiators Easy Setup and Management The Aruba Instant On mobile app allows you to set up, manage, and monitor Instant On switches and access points directly from your phone. Within the app, you get guided step-by-step instructions to install Instant On devices to get your network up and running quickly - no technical expertise required. And cloud-based access allows you to access the network from anywhere, at any time. Non-intrusive, Aesthetic Design Aruba Instant On switches are designed to complement the sleek and clean look of the Instant On access points, and to blend discreetly into your site's environment. The 8-port models, as well as the 24- and 48-port non PoE models, are fan-less, making them ideal for quiet office deployments. High Performance with Flexible Options The series consists of four (4) Class 4 PoE switches, and three (3) non-PoE switches including 8- 24- and 48-port Gigabit Ethernet switches. The two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models, ensure high performance and eliminate traffic bottlenecks across the network. Customizable features include basic Layer 2 features like VLANs and link aggregation, as well as advanced features such as Layer 3 IPv4 static routing, ACLs, and Spanning Tree Protocols, and IPv6 Host mode. Optimized User Experience The Aruba Instant On mobile app provides common workflows for Instant On switches and access points making it easier to configure, monitor and manage your network remotely without the need for additional hardware like cloud keys or VPN. You can also update firmware on your Instant On devices directly from the cloud whenever you want, from wherever you are. Site inventory The site inventory feature on the Instant On mobile app shows you all switches and AP's on a single screen, allowing you to quickly identify non-functioning devices and troubleshoot accordingly. Multi-Site Management The cloud-hosted web interface and mobile app make it easy to manage multiple sites, multiple networks, distributed deployments and multi-tenant deployments. Each site is logically separated and has its own configuration, statistics, guest portal, and admin read/write privileges. Built-In Security Built-in security features protect your network from external threats by blocking malware attacks and keeping unauthorized users off the network. Network traffic can be filtered and access restricted based on MAC and IP address. No Hidden Fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry leading limited lifetime warranty are also included, along with chat support for the life of the product. Management Cloud-Based Management for Entire Network The cloud-hosted web interface and mobile app make it easy to manage networks with Instant On APs and Switches. Simple Local Web GUI Management For management of individual switches, the intuitive Web GUI makes management simple, even for non-technical users. Supports up to five (5) HTTP and HTTP Secure (HTTPS) sessions. Firmware Update Provides notification of the latest firmware with the ability to schedule update at a preferred time through Instant On mobile app and cloud-based web portal. Default DHCP Client Mode Allows the switch to be directly connected to a network, enabling plug-and-play operation. In the absence of a DHCP server on the network, the switch falls back to the static address 192.168.1.1. Port Mirroring Enables traffic on a port or VLAN to be simultaneously sent to a network analyzer for monitoring. Event Logging and Alerts Provides detailed information for problem identification and resolution. Account Management Allows administrators to add, modify, delete and transfer management accounts and passwords for secure access to Instant cloud management solution. Locator LED Allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches. Schedule Configuration Global Schedule feature can be applied to time-based ACLs, port or interface shutdown, or PoE power delivery; up to 3 schedules can be configured. PoE scheduling allows user to configure a specific day/time of the week (e.g. business hours) for Instant On switches to supply power to connected devices (e.g. surveillance cameras, access points etc.). Quality of Service (QoS) Traffic Prioritization Provides time-sensitive packets (like VoIP and video) with priority over other traffic based on DSCP or IEEE 802.1p classification. IEEE 802.1p/Q VLAN Tagging Delivers data to devices based on the priority and type of traffic; supports IEEE 802.1Q. Class of Service (CoS) Sets the IEEE 802.1p/DSCP priority to queue mapping (4 queues). Supports strict priority queuing (SP) or weighted round robin (WRR) queuing. SP and WRR queuing can be configured on individual switch ports. Advanced Classifier Based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information. Access Switching SFP/SFP+ Fiber Connectivity Provides fiber connections for uplinks and other connections across longer distances than copper cabling can support. SFP ports are in addition to available copper Ethernet ports, providing a higher total number of available ports. Two (2) SFP 1G ports available on 8-port models and four (4) SFP+ 1G/10G ports on 24-/48 port models. Ethernet Alliance Certified Class 4 PoE (IEEE 802.3at) Provides up to 30 W per port, which allows support of the class 4 PoE capable devices such as video IP phones, wireless access points, and advanced pan/tilt/zoom security cameras, as well as any 15.4 W IEEE 802.3af-compliant end device; mitigates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. Auto-PoE Power Configuration The switch automatically assigns the required power to a port for a PD device based on Link Layer Discovery Protocol (LLDP). PoE Power Allocation Support multiple methods (LLDP-MED automatic, class of PoE, or usage-based) to allocate PoE power for more efficient energy savings. Auto MDI/MDI-X Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports. Network Security TPM-Based Security Includes a Trusted Platform Module (TPM) for secure hardware- based generation and storage of cryptographic keys used for secure connection to the Instant On cloud portal. IEEE 802.1Q VLAN Support Support for up to 256 VLANs with a VLAN ID range of 2-4093. IEEE 802.1X Access Control Authentication of network users on a per port basis prior to permitting network access. Port authentication includes RADIUS assigned VLAN, dynamic VLAN creation, guest VLAN or into an unauthenticated VLAN. Automatic Denial-of-Service Protection Monitors for malicious attacks and protects the network by blocking the attacks. Packet Storm Protection Protects against unknown unicast, broadcast and multicast storms with user-defined thresholds. RADIUS The switch supports RADIUS authentication with primary and backup server configuration. Automatic VLAN Assignment - RADIUS Assigned VLANs Automatically assigns users to the appropriate VLAN based on their identity and location. RADIUS Accounting A robust set of attributes and statistics are available for collecting information from the switch. Management VLAN ID Provides secure management access to administrators in the specified VLAN. Link Flap Prevention Minimizes the network disruption by automatically detecting and disabling ports that experience link flap events. Performance and Efficiency Energy Efficient Ethernet (EEE) Compliant with IEEE 802.3az standard requirements to save energy during periods of low data activity. Auto-Port Shut Down The switch saves power by automatically shutting down power to inactive ports. Power is restored on a port upon link detection. Energy Savings Status The switch provides an estimated cumulative energy savings due to green Ethernet features being enabled. Energy-Efficient Cooling Includes variable speed fans operating only at the speed necessary to maintain operating temperature to reduce excess noise and power consumption. Fan-Less Operation Fan-less design for 8-port models, 24- and 48-port non-PoE models, making the switches ideal for office deployments. Switching Features IEEE 802.3x Flow Control Provides a flow-throttling mechanism propagated through the network to prevent packet loss at a congested node. Spanning Tree Protocol (STP) Supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP on local web). Loop Protection If the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms. BPDU Filtering Drops BPDU packets when STP is enabled globally but disabled on a specific port. Jumbo Frame Support Supports up to 9216 bytes frame size to improve the performance of large data transfers. IGMP Snooping v1/v2 Improves network performance through multicast filtering, instead of flooding traffic on all ports. Link Aggregation Groups together multiple ports up to a maximum of eight (8) ports per trunk automatically using Link Aggregation Control Protocol (LACP), or manually, to form a high-bandwidth connection to the network backbone that helps prevent traffic bottlenecks. The 8-port models support 4 trunks, 24-port models support 8 trunks, and 48-port models support 16 trunks. LLDP/LLDP-MED (Media Endpoint Discovery) Defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN for automatic configuration of network devices such as IP phones. Address Resolution Protocol (ARP) The ARP table displays all of the IP addresses that have been resolved to MAC addresses, either dynamically or through static entry configuration. Additional Features Accessed Through Local Web-Management Interface Top Event Dashboard Provides notifications for critical events and a quick access to the latest log events. Quick Start-Up and VLAN Wizard Enables automatic configuring of the initial settings such IP address, device information, and system time. VLAN wizard can be used for setting up initial VLAN IDs and port membership. Access Control Lists (ACLs) Enables network traffic filtering by creating an ACL, adds rules and matches criteria to an ACL, and applies the ACL to permit or deny on one or more interfaces or a VLAN. Supports for 50 inbound IPv4 and MAC ACLs with up to 480 ACEs. IPv6 Host Enables switches to be managed and deployed at the IPv6 network's edge. Rate Limiting Sets and enforces per-port ingress traffic limits based on percentages or packets per second. Protected Ports Ports in a port isolation group are restricted from forwarding Layer 2 traffic between ports in that group, providing data privacy and security. SCP and TFTP File Transfer Provides different mechanisms for secure file transfer through SCP (Secure Copy Protocol) or TFTP. Dual Image Support Provide independent primary and secondary software images for backup while upgrading. User Account Management Password strength checking and aging feature provides enhanced security to user account administration to the local web management interface. Additionally, user account authentication can now be done via RADIUS to access the web-interface.' Secure Sockets Layer (SSL) Encrypts all HTTP traffic, secures access to the local browser-based management of the switch. SNMPv1, v2c, and v3 Facilitates remote management with SNMP management station that discovers and monitors the switch. Remote Monitoring (RMON) Provides advanced monitoring and reporting capabilities for statistics, history, alarms and events. RMON data is retrieved from the switch through a network management platform over SNMP. Cable Diagnostic Tool Provides the mechanism to detect and report potential cabling issues, such as cable opens or cable shorts on copper links, in addition to providing distance to the fault and total length of cable. Warranty, Service and Support Aruba Instant On Limited Lifetime Support provides 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is included for the life of the product. Refer to the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. Standards and Protocols (applies to all products in series) IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3z 1000BASE-X IEEE 802.2af PoE 1 (PoE models only) IEEE 802.3at PoE 1 (PoE models only) IEEE 802.3x Flow control IEEE 802.1Q VLANS IEEE 802.1p Priority IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.1X Port Access Authentication IEEE 802.3az Energy Efficient Ethernet IEEE 802.1D: Spanning Tree Protocol IEEE 802.1W: Rapid Spanning Tree Protocol IEEE 802.1S: Multiple Spanning Tree Protocol IEEE 802.1AB Link Layer Discovery Protocol Denial of service protection CPU DoS protection (tonerpartner.cz)
Podobné produkty ako Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 195W Switch , Hpe microserver gen10+ (p16006-421)HPE Aruba Networking CX 6100 48G Class4 PoE 4SFP+ 370W Switch RENEW JL675A Klíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE a až 370 W PoE třídy 4 pro podporu zařízení IoT. Kompaktní 12portový model bez ventilátoru pro tichý chod. Flexibilita správy s podporou Aruba Central, snadno použitelné webové grafické rozhraní, rozhraní CLI a Aruba NetEdit. Jednoduché nasazení s funkcí Zero Touch Provisioning. Připravenost na softwarovou definici s rozhraními REST API. Zjednodušení přidávání, přesunů a změn pomocí bezbarvého systému portů. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti. Specifications Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A) Description 48x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports Supports PoE Standards IEEE 802.3af, 802.3at 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (500W) Up to 370W of Class 4 PoE Power Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 30.48 cm (1.73" x 17.4" x 12.0") Configuration Weight 5.02 kg (11.07 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 176 Gbps Model Throughput Capacity 98.6 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.9 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 4.3 Bel Sound Pressure, LpAm (Bystander) = 29.8 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 4.9 A / 2.4 A Power Consumption (230 VAC) Idle: 30.6W Max Power (w/o PoE): 45W Max Power (w/ PoE): 480W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6100 48G Class4 PoE 4SFP+ 370W Switch RENEW JL675A , Evga 850 gq power supply uk (210-gq-0850-v3)Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 370W Switch I/O Ports and Slots 24 RJ-45 autosensing 10/100/1000 Class 4 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 10.42(d) x 1.73(h) in (44.25 x 26.47 x 4.39 cm) (1U height) Weight 8.10 lb (3.67kg) Processor and Memory ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5 MB Memory And Flash 512 MB SDRAM 256 MB flash Packet Buffer 1.5 MB Performance 100 Mb latency < 4.7 uSec 1000 Mb latency 10000 Mb latency Throughput (Mpps) 95.23 Mpps Capacity 128 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 71 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic Pressure: 32.2 dBA Power: 58.5 dB Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current 4.8/2.4 A Maximum power rating 439.0 W Idle power 20.9 W PoE power 370 W Class 4 PoE Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF XCVR (J4859D) Aruba 1G SFP RJ45 T 100m Cat5e XCVR (J8177D) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) High-performance, smart-managed switches designed with small businesses in mind Whether you own a cafe, a design firm or a tech startup, a reliable and secure network plays a critical role in the success of your business. And you need a network solution that gives you peace of mind, allowing you to focus on growing your business instead of managing problems with your network. Aruba Instant On makes it easy to keep network users happy, mobile and IoT devices connected, and your network secure. The Aruba Instant On 1930 switches features advanced, smart-managed, fixed- configuration Gigabit switches designed for small businesses that are easy-to-deploy and affordable. They're made to handle today's bandwidth-heavy applications like voice and video conferencing, enabling consistent connectivity to enhance performance. Using either the Instant On mobile app or the cloud-based web portal, you can quickly set up, monitor and manage the 1930 switch series from anywhere at any time. What's more, up to 30 W PoE power delivery is available out-of-the-box for your class 4 PoE devices, like access points, surveillance cameras and VoIP phones, all easily managed from the same platform. Built-in security features protect your network from unauthorized access by allowing you to segment traffic and define access to each area of the network. And all of this is included in the price of the hardware - there are no hidden subscription or licensing fees. Key Features Smart-managed layer 2+ Ethernet switch series ready to deploy in 8-, 24-and 48-port for non-PoE and Class 4 PoE (i.e. PoE+) models PoE to power APs and IoT devices like IP phones, surveillance cameras and door locks Two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models to eliminate traffic bottlenecks across your network Security controls let you define access in each area of your network, keeping your business data safe Convenient mobile app and web- based GUI for set up, management and troubleshooting. Standard Features Simplicity at its best Plug-and-play switches that work together with Instant On APs right out of the box Mobile app to easily setup, monitor and manage your network Security you can count on Protect your network from unauthorized access with IEEE 802.1X and VLANs Automatic denial-of-service (DOS) monitors and protects the network against malicious attacks We've got you covered No extra licensing or subscription fees Industry-leading limited lifetime warranty and support. The Instant On Differentiators Easy setup and management The Aruba Instant On mobile app allows you to set up, manage, and monitor Instant On switches and access points directly from your phone. Within the app, you get guided step-by-step instructions to install Instant On devices to get your network up and running quickly - no technical expertise required. And cloud-based access allows you to access the network from anywhere, at any time. Non-intrusive, aesthetic design Aruba Instant On switches are designed to complement the sleek and clean look of the Instant On access points, and to blend discreetly into your site's environment. The 8-port models, as well as the 24- and 48-port non PoE+ models, are fan-less, making them ideal for quiet office deployments. High performance with flexible options The series consists of four (4) Class 4 PoE (PoE+) switches, and three (3) non-POE switches including 8- 24- and 48-port Gigabit Ethernet switches. The two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models, ensure high performance and eliminate traffic bottlenecks across the network. Customizable features include basic Layer 2 features like VLANs and link aggregation, as well as advanced features such as Layer 3 IPv4 static routing, ACLs, and Spanning Tree Protocols, and IPv6 Host mode. Optimized user experience The Aruba Instant On mobile app provides common workflows for Instant On switches and access points making it easier to configure, monitor and manage your network remotely without the need for additional hardware like cloud keys or VPN. You can also update firmware on your Instant On devices directly from the cloud whenever you want, from wherever you are. Site inventory The site inventory feature on the Instant On mobile app shows you all switches and AP's on a single screen, allowing you to quickly identify non-functioning devices and troubleshoot accordingly. Multi-site management The cloud-hosted web interface and mobile app make it easy to manage multiple sites, multiple networks, distributed deployments and multi-tenant deployments. Each site is logically separated and has its own configuration, statistics, guest portal, and admin read/write privileges. Built-in security Built-in security features protect your network from external threats by blocking malware attacks and keeping unauthorized users off the network. Network traffic can be filtered and access restricted based on MAC and IP address. No hidden fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry leading limited lifetime warranty are also included, along with chat support for the life of the product. Management Cloud-based management for entire network The cloud-hosted web interface and mobile app make it easy to manage networks with Instant On APs and Switches. Simple local web GUI management For management of individual switches, the intuitive Web GUI makes management simple, even for non-technical users. Supports up to five (5) HTTP and HTTP Secure (HTTPS) sessions. Firmware update Provides notification of the latest firmware with the ability to schedule update at a preferred time through Instant On mobile app and cloud-based web portal. Default DHCP client mode Allows the switch to be directly connected to a network, enabling plug-and-play operation. In the absence of a DHCP server on the network, the switch falls back to the static address 192.168.1.1. Port mirroring Enables traffic on a port or VLAN to be simultaneously sent to a network analyzer for monitoring. Event logging and alerts Provides detailed information for problem identification and resolution. Account management Allows administrators to add, modify, delete and transfer management accounts, passwords for secure access to Instant cloud mngmnt solution. Locator LED Allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches. Quality of Service (QoS) Traffic prioritization Provides time-sensitive packets (like VoIP and video) with priority over other traffic based on DSCP or IEEE 802.1p classification. IEEE 802.1p/Q VLAN tagging Delivers data to devices based on the priority and type of traffic; supports IEEE 802.1Q. Class of Service (CoS) Sets the IEEE 802.1p/DSCP priority to queue mapping (4 queues). Supports strict priority queuing (SP) or weighted round robin (WRR) queuing. SP and WRR queuing can be configured on individual switch ports. Advanced classifier based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information. Access Switching SFP/SFP+ fiber connectivity Provides fiber connections for uplinks and other connections across longer distances than copper cabling can support. SFP ports are in addition to available copper Ethernet ports, providing a higher total number of available ports. Two (2) SFP 1G ports available on 8-port models and four (4) SFP+ 1G/10G ports on 24-/48 port models. Ethernet Alliance Certified Class 4 PoE (PoE+; IEEE 802.3at) Provides up to 30 W per port, which allows support of the class 4 PoE (i.e. PoE+) capable devices such as video IP phones, wireless access points, and advanced pan/tilt/zoom security cameras, as well as any 15.4 W IEEE 802.3af-compliant end device; mitigates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. Auto-PoE power configuration The switch automatically assigns the required power to a port for a PD device based on Link Layer Discovery Protocol (LLDP). PoE power allocation Support multiple methods (LLDP-MED automatic, class of PoE, or usage-based) to allocate PoE power for more efficient energy savings. Auto MDI/MDI-X Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports. Network Security TPM-based security Includes a Trusted Platform Module (TPM) for secure hardware- based generation and storage of cryptographic keys used for secure connection to the Instant On cloud portal. IEEE 802.1Q VLAN support Support for up to 256 VLANs with a VLAN ID range of 2-4093. IEEE 802.1X access control Authentication of network users on a per port basis prior to permitting network access. Port authentication includes RADIUS assigned VLAN, dynamic VLAN creation, guest VLAN or into an unauthenticated VLAN. Automatic denial-of-service protection Monitors for malicious attacks and protects the network by blocking the attacks. Packet storm protection Protects against unknown unicast, broadcast and multicast storms with user-defined thresholds. RADIUS The switch supports RADIUS authentication with primary and backup server configuration. RADIUS accounting A robust set of attributes and statistics are available for collecting information from the switch. Management VLAN ID Provides secure management access to administrators in the specified VLAN. Link Flap prevention Minimizes the network disruption by automatically detecting and disabling ports that experience link flap events. Performance and Efficiency Energy Efficient Ethernet (EEE) Compliant with IEEE 802.3az standard requirements to save energy during periods of low data activity. Auto-port shut down The switch saves power by automatically shutting down power to inactive ports. Power is restored on a port upon link detection. Energy savings status The switch provides an estimated cumulative energy savings due to green Ethernet features being enabled. Energy-efficient cooling Includes variable speed fans operating only at speed necessary to maintain operating temperature to reduce excess noise + power consumption. Fan-less operation Fan-less design for 8-port models, 24- and 48-port non-PoE models, making the switches ideal for office deployments. Switching Features IEEE 802.3x Flow control Provides a flow-throttling mechanism propagated through the network to prevent packet loss at a congested node. Spanning Tree Protocol (STP) Supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP on local web). Loop protection If the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms. BPDU filtering Drops BPDU packets when STP is enabled globally but disabled on a specific port. Jumbo frame support Supports up to 9216 bytes frame size to improve the performance of large data transfers. IGMP snooping v1/v2 Improves network performance through multicast filtering, instead of flooding traffic on all ports. Link aggregation Groups together multiple ports up to a maximum of eight (8) ports per trunk automatically using Link Aggregation Control Protocol (LACP), or manually, to form a high-bandwidth connection to the network backbone that helps prevent traffic bottlenecks. The 8-port models support 4 trunks, 24-port models support 8 trunks, and 48-port models support 16 trunks. LLDP/LLDP-MED (Media Endpoint Discovery) Defines standard extension of LLDP that stores values for parameters suchas QoSand VLAN for autoconfiguration of netw devices such as IPphones. Address Resolution Protocol (ARP) The ARP table displays all of the IP addresses that have been resolved to MAC addresses, either dynamically or through static entry configuration. Features Accessed Through Local Web-Management Interface Static IPv4 routing Supports manual routing configuration of up to 32 static routes. Auto-voice VLAN Recognizes IP phones and automatically assigns voice traffic to dedicated VLAN for IP phones. PoE scheduling A PoE scheduler provides the ability to define the hours of PoE power being supplied to a group of switch ports based on a 24-hour day. The scheduler enables the flexibility to select individual days of a week as well as reccurrence on a weekly basis with a start and end date. Access Control Lists (ACLs) Enables network traffic filtering by creating an ACL, adds rules and matches criteria to an ACL, and applies the ACL to permit or deny on one or more interfaces or a VLAN. Supports 50 inbound IPv4 and MAC ACLs with up to 480 ACEs. IPv6 host Enables switches to be managed and deployed at the IPv6 network's edge. Rate limiting Sets and enforces per-port ingress traffic limits based on percentages or packets per second. ARP Attack prevention Dynamic ARP protection blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data. DHCP snooping Provides network security by filtering untrusted DHCP messages. Port security Ports in a port isolation group are restricted from forwarding Layer 2 traffic between ports in that group, providing data privacy and security. SCP and TFTP file transfer Provides different mechanisms for secure file transfer through SCP (Secure Copy Protocol) or TFTP. Dual image support Provide independent primary and secondary software images for backup while upgrading. User account management Password strength checking and aging feature provides enhanced security to user account administration to the local web management interface. Secure Sockets Layer (SSL) Encrypts all HTTP traffic, secures access to the local browser- based management of the switch. SNMPv1, v2c, and v3 Facilitate management of the switch, as the device can be discovered and monitored from an SNMP management station. Remote monitoring (RMON) Remote monitoring (RMON) provides advanced monitoring and reporting capabilities for statistics, history, alarms and events. RMON data is retrieved from the switch through a network management platform over SNMP. Warranty, Service and Support Aruba Instant On Limited Lifetime Support provides 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is included for the life of the product. Refer to the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. (patro.cz)
Podobné produkty ako Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 370W Switch, JL684A , Elektrobock pt04-ei (0645)Aruba 6000 24x ports 10/100/1000BASE-T Ports 4SFP Switch. Aruba 6000 24G 4SFP Switch Model Aruba 6000 24G 4SFP Switch (R8N88A) Description 24x ports 10/100/1000BASE-T Ports 4x 1G SFP ports 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply Fans Fixed fans Dimensions (H) 4.39 cm (W) 44.2 cm (D) 20.12 cm (1.73" x 17.4" x 7.92") Configuration Weight 2.62 kg (5.78 lbs) CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Model Switching Capacity 56 Gbps Model Throughput Capacity 41.6 Mpps Average Latency (LIFO-64-bytes packets) 1 Gbps: 1.5 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.9 Bel Sound Pressure, LpAm (Bystander) = 20.9 dB Primary Airflow Side-to-side Aruba 6000 24G 4SFP Switch (R8N88A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (tonerpartner.cz)
Podobné produkty ako Aruba 6000 24G 4SFP Switch. , Tetra repto min 1 l (4004218204270)Aruba 2930F 24G 4SFP Swch Renew JL259A 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/ 100BASE-TX: half or full; 1000BASE-T: full only (patro.cz)
Podobné produkty ako Aruba 2930F 24G 4SFP Swch + Energy drink HPE ARUBA, JL259A , Braun clean & renew kazety, balení 5+1 (4210201205593)Aruba 2930F 24G PoE+ 4SFP Swch RENEW JL261A (tonerpartner.cz)
Podobné produkty ako Aruba 2930F 24G PoE+ 4SFP Swch RENEW JL261A , Target - darts šipky steel phil taylor power 9zero - 24g (75560)HPE X240 10G SFP+ SFP+ 3m DAC Remanufactured Cable (patro.cz)
Podobné produkty ako HPE X240 10G SFP+ SFP+ 3m DAC HP RENEW Cbl JD097CR, JD097CR , Vention 4-port usb 2.0 hub with power supply 0.5m black (chmbd)Řada přepínačů Aruba CX 6100 je moderní rodina přístupových přepínačů základní úrovně ideální pro pobočky, střední podniky a sítě SMB. Přepínače Aruba CX 6100, navržené pro spolehlivý, jednoduchý a bezpečný přístup, poskytují pohodlné řešení kabelového přístupu pro podnikové sítě podporující IoT, mobilní a cloudové aplikace. Technické parametry 24x 10/100/1000Base-T porty 4x 1/10G SFP porty 1x USB-C Console Port, 1x USB Type-A Host port Interní (pevný) napájecí zdroj (500 W), pevné ventilátory Maximální výkon: 32,7 W bez PoE, 455 W s PoE Vstupní napětí: 100-127 VAC / 200-240 VAC Přepínací kapacita: 128 Gb/s Propustnost: 95,2 Mpps Procesor: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť a Flash: 4 GB DDR3, 16 GB eMMC Možnost PoE: Až 370W Class 4 PoE Rozměry: 4,39 x 44,2 x 26,82 cm Hmotnost: 4,2 kg Specifications Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch (JL677A) Description 24x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports Supports PoE Standards IEEE 802.3af, 802.3at 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (500W) Up to 370W of Class 4 PoE Power Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 26.82 cm (1.73" x 17.4" x 10.56") Configuration Weight 4.19kg (9.24 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 128 Gbps Model Throughput Capacity 95.2 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.5 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch (JL677A) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.9 Bel Sound Pressure, LpAm (Bystander)= 24.3 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 4.6 A / 2.3 A Power Consumption (230 VAC) Idle: 22.9W Max Power (w/o PoE): 32.7W Max Power (w/ PoE): 455W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch (JL677A) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (tonerpartner.cz)
Podobné produkty ako Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch , Scangrip power supply 80 w - napájecí zdroj pro světla line light (03.5226)HPE 1950-24G-2SFP+-2XGT Remanufactured Swch (tonerpartner.cz)
Podobné produkty ako HPE 1950-24G-2SFP+-2XGT HP Swch JG960AR RENEW , Scangrip power supply 25 w - napájecí zdroj pro světla line light (03.5229)Aruba Instant On 1930 48G 4SFP/SFP+ Switch EAN: 190017356112 Porty a sloty 48 RJ-45 autosensing 10/100/1000 portů 4 SFP+ 1/10GbE porty Fyzické charakteristiky Rozměry: 44,2(w) x 28,2(d) x 4,4(h) cm Hmotnost: 3.13 kg Výkon CPU: ARM Cortex-A9 @ 800 MHz Paměť a flash: 512 MB SDRAM, 256 MB flash Buffer paketů: 1.5 MB Latence 100 Mb: < 4.5 uSec Latence 1000 Mb: <2.2 uSec Latence 10000 Mb: <1.2 uSec Průtok (Mpps): 130.95 Mpps Kapacita: 176 Gbps Provozní podmínky Provozní teplota: 0°C až 40°C Provozní vlhkost: 15% až 95% při 40°C Nepracovní teplota: -40°C až 70°C Nepracovní vlhkost: 15% až 95% při 60°C Výška: do 3.048 Km Elektrické charakteristiky Frekvence: 50-60 Hz AC napětí: 100 - 127 / 200 - 240 VAC Proud: .8 A/.5 A Maximální výkon: 36.9 W Nečinný výkon: 16.8 W Správa zařízení Aruba Instant On Cloud; Webový prohlížeč; SNMP Manager Montáž Montáž do standardního 19" telco racku nebo skříňky. Sada pro montáž do 2-post racku je součástí balení. Podporuje montáž na stůl Podporuje montáž na stěnu s porty směřujícími nahoru nebo dolů Podporuje montáž pod stůl pomocí přiložených držáků Transceivery Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A ) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) (tonerpartner.cz)
Podobné produkty ako Aruba Instant On 1930 48G 4SFP/SFP+ Switch , Vention 4-port usb 2.0 hub with power supply 0.15m black (chmbb)Aruba Instant On 1930 48G 4SFP/SFP+ Switch (JL685A) I/O Ports and Slots 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 11.12(d) x 1.73(h) in (44.25 x 28.24 x 4.39 cm) (1U height) Weight 6.91 lb (3.13 kg) CPU ARM Cortex-A9 @ 800 MHz Memory And Flash 512 MB SDRAM 256 MB flash Packet Buffer 1.5 MB Performance 100 Mb latency < 4.5 uSec 1000 Mb latency <2.2 uSec 10000 Mb latency <1.2 uSec Throughput (Mpps) 130.95 Mpps Capacity 176 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 114 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic Power: 0 dB (no fan) Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current .8/.5 A Maximum power rating 36.9 W Idle power 16.8 W PoE power n/a Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Must be mounted top surface up. To prevent possible impact to longterm reliability, product should not be mounted upside-down Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A ) Aruba 1G SFP LC LX 10km SMF XCVR (J4859D) Aruba 1G SFP RJ45 T 100m Cat5e XCVR (J8177D) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) High-performance, smart-managed switches designed with small businesses in mind Whether you own a cafe, a design firm or a tech startup, a reliable and secure network plays a critical role in the success of your business. And you need a network solution that gives you peace of mind, allowing you to focus on growing your business instead of managing problems with your network. Aruba Instant On makes it easy to keep network users happy, mobile and IoT devices connected, and your network secure. The Aruba Instant On 1930 switches features advanced, smart-managed, fixed- configuration Gigabit switches designed for small businesses that are easy-to-deploy and affordable. They're made to handle today's bandwidth-heavy applications like voice and video conferencing, enabling consistent connectivity to enhance performance. Using either the Instant On mobile app or the cloud-based web portal, you can quickly set up, monitor and manage the 1930 switch series from anywhere at any time. What's more, up to 30 W PoE power delivery is available out-of-the-box for your class 4 PoE devices, like access points, surveillance cameras and VoIP phones, all easily managed from the same platform. Built-in security features protect your network from unauthorized access by allowing you to segment traffic and define access to each area of the network. And all of this is included in the price of the hardware - there are no hidden subscription or licensing fees. Key Features Smart-managed layer 2+ Ethernet switch series ready to deploy in 8-, 24-and 48-port for non-PoE and Class 4 PoE (i.e. PoE+) models PoE to power APs and IoT devices like IP phones, surveillance cameras and door locks Two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models to eliminate traffic bottlenecks across your network Security controls let you define access in each area of your network, keeping your business data safe Convenient mobile app and web- based GUI for set up, management and troubleshooting. Standard Features Simplicity at its best Plug-and-play switches that work together with Instant On APs right out of the box Mobile app to easily setup, monitor and manage your network Security you can count on Protect your network from unauthorized access with IEEE 802.1X and VLANs Automatic denial-of-service (DOS) monitors and protects the network against malicious attacks We've got you covered No extra licensing or subscription fees Industry-leading limited lifetime warranty and support. The Instant On Differentiators Easy setup and management The Aruba Instant On mobile app allows you to set up, manage, and monitor Instant On switches and access points directly from your phone. Within the app, you get guided step-by-step instructions to install Instant On devices to get your network up and running quickly - no technical expertise required. And cloud-based access allows you to access the network from anywhere, at any time. Non-intrusive, aesthetic design Aruba Instant On switches are designed to complement the sleek and clean look of the Instant On access points, and to blend discreetly into your site's environment. The 8-port models, as well as the 24- and 48-port non PoE+ models, are fan-less, making them ideal for quiet office deployments. High performance with flexible options The series consists of four (4) Class 4 PoE (PoE+) switches, and three (3) non-POE switches including 8- 24- and 48-port Gigabit Ethernet switches. The two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models, ensure high performance and eliminate traffic bottlenecks across the network. Customizable features include basic Layer 2 features like VLANs and link aggregation, as well as advanced features such as Layer 3 IPv4 static routing, ACLs, and Spanning Tree Protocols, and IPv6 Host mode. Optimized user experience The Aruba Instant On mobile app provides common workflows for Instant On switches and access points making it easier to configure, monitor and manage your network remotely without the need for additional hardware like cloud keys or VPN. You can also update firmware on your Instant On devices directly from the cloud whenever you want, from wherever you are. Site inventory The site inventory feature on the Instant On mobile app shows you all switches and AP's on a single screen, allowing you to quickly identify non-functioning devices and troubleshoot accordingly. Multi-site management The cloud-hosted web interface and mobile app make it easy to manage multiple sites, multiple networks, distributed deployments and multi-tenant deployments. Each site is logically separated and has its own configuration, statistics, guest portal, and admin read/write privileges. Built-in security Built-in security features protect your network from external threats by blocking malware attacks and keeping unauthorized users off the network. Network traffic can be filtered and access restricted based on MAC and IP address. No hidden fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry leading limited lifetime warranty are also included, along with chat support for the life of the product. Management Cloud-based management for entire network The cloud-hosted web interface and mobile app make it easy to manage networks with Instant On APs and Switches. Simple local web GUI management For management of individual switches, the intuitive Web GUI makes management simple, even for non-technical users. Supports up to five (5) HTTP and HTTP Secure (HTTPS) sessions. Firmware update Provides notification of the latest firmware with the ability to schedule update at a preferred time through Instant On mobile app and cloud-based web portal. Default DHCP client mode Allows the switch to be directly connected to a network, enabling plug-and-play operation. In the absence of a DHCP server on the network, the switch falls back to the static address 192.168.1.1. Port mirroring Enables traffic on a port or VLAN to be simultaneously sent to a network analyzer for monitoring. Event logging and alerts Provides detailed information for problem identification and resolution. Account management Allows administrators to add, modify, delete and transfer management accounts, passwords for secure access to Instant cloud mngmnt solution. Locator LED Allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches. Quality of Service (QoS) Traffic prioritization Provides time-sensitive packets (like VoIP and video) with priority over other traffic based on DSCP or IEEE 802.1p classification. IEEE 802.1p/Q VLAN tagging Delivers data to devices based on the priority and type of traffic; supports IEEE 802.1Q. Class of Service (CoS) Sets the IEEE 802.1p/DSCP priority to queue mapping (4 queues). Supports strict priority queuing (SP) or weighted round robin (WRR) queuing. SP and WRR queuing can be configured on individual switch ports. Advanced classifier based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information. Access Switching SFP/SFP+ fiber connectivity Provides fiber connections for uplinks and other connections across longer distances than copper cabling can support. SFP ports are in addition to available copper Ethernet ports, providing a higher total number of available ports. Two (2) SFP 1G ports available on 8-port models and four (4) SFP+ 1G/10G ports on 24-/48 port models. Ethernet Alliance Certified Class 4 PoE (PoE+; IEEE 802.3at) Provides up to 30 W per port, which allows support of the class 4 PoE (i.e. PoE+) capable devices such as video IP phones, wireless access points, and advanced pan/tilt/zoom security cameras, as well as any 15.4 W IEEE 802.3af-compliant end device; mitigates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. Auto-PoE power configuration The switch automatically assigns the required power to a port for a PD device based on Link Layer Discovery Protocol (LLDP). PoE power allocation Support multiple methods (LLDP-MED automatic, class of PoE, or usage-based) to allocate PoE power for more efficient energy savings. Auto MDI/MDI-X Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports. Network Security TPM-based security Includes a Trusted Platform Module (TPM) for secure hardware- based generation and storage of cryptographic keys used for secure connection to the Instant On cloud portal. IEEE 802.1Q VLAN support Support for up to 256 VLANs with a VLAN ID range of 2-4093. IEEE 802.1X access control Authentication of network users on a per port basis prior to permitting network access. Port authentication includes RADIUS assigned VLAN, dynamic VLAN creation, guest VLAN or into an unauthenticated VLAN. Automatic denial-of-service protection Monitors for malicious attacks and protects the network by blocking the attacks. Packet storm protection Protects against unknown unicast, broadcast and multicast storms with user-defined thresholds. RADIUS The switch supports RADIUS authentication with primary and backup server configuration. RADIUS accounting A robust set of attributes and statistics are available for collecting information from the switch. Management VLAN ID Provides secure management access to administrators in the specified VLAN. Link Flap prevention Minimizes the network disruption by automatically detecting and disabling ports that experience link flap events. Performance and Efficiency Energy Efficient Ethernet (EEE) Compliant with IEEE 802.3az standard requirements to save energy during periods of low data activity. Auto-port shut down The switch saves power by automatically shutting down power to inactive ports. Power is restored on a port upon link detection. Energy savings status The switch provides an estimated cumulative energy savings due to green Ethernet features being enabled. Energy-efficient cooling Includes variable speed fans operating only at speed necessary to maintain operating temperature to reduce excess noise + power consumption. Fan-less operation Fan-less design for 8-port models, 24- and 48-port non-PoE models, making the switches ideal for office deployments. Switching Features IEEE 802.3x Flow control Provides a flow-throttling mechanism propagated through the network to prevent packet loss at a congested node. Spanning Tree Protocol (STP) Supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP on local web). Loop protection If the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms. BPDU filtering Drops BPDU packets when STP is enabled globally but disabled on a specific port. Jumbo frame support Supports up to 9216 bytes frame size to improve the performance of large data transfers. IGMP snooping v1/v2 Improves network performance through multicast filtering, instead of flooding traffic on all ports. Link aggregation Groups together multiple ports up to a maximum of eight (8) ports per trunk automatically using Link Aggregation Control Protocol (LACP), or manually, to form a high-bandwidth connection to the network backbone that helps prevent traffic bottlenecks. The 8-port models support 4 trunks, 24-port models support 8 trunks, and 48-port models support 16 trunks. LLDP/LLDP-MED (Media Endpoint Discovery) Defines standard extension of LLDP that stores values for parameters suchas QoSand VLAN for autoconfiguration of netw devices such as IPphones. Address Resolution Protocol (ARP) The ARP table displays all of the IP addresses that have been resolved to MAC addresses, either dynamically or through static entry configuration. Features Accessed Through Local Web-Management Interface Static IPv4 routing Supports manual routing configuration of up to 32 static routes. Auto-voice VLAN Recognizes IP phones and automatically assigns voice traffic to dedicated VLAN for IP phones. PoE scheduling A PoE scheduler provides the ability to define the hours of PoE power being supplied to a group of switch ports based on a 24-hour day. The scheduler enables the flexibility to select individual days of a week as well as reccurrence on a weekly basis with a start and end date. Access Control Lists (ACLs) Enables network traffic filtering by creating an ACL, adds rules and matches criteria to an ACL, and applies the ACL to permit or deny on one or more interfaces or a VLAN. Supports 50 inbound IPv4 and MAC ACLs with up to 480 ACEs. IPv6 host Enables switches to be managed and deployed at the IPv6 network's edge. Rate limiting Sets and enforces per-port ingress traffic limits based on percentages or packets per second. ARP Attack prevention Dynamic ARP protection blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data. DHCP snooping Provides network security by filtering untrusted DHCP messages. Port security Ports in a port isolation group are restricted from forwarding Layer 2 traffic between ports in that group, providing data privacy and security. SCP and TFTP file transfer Provides different mechanisms for secure file transfer through SCP (Secure Copy Protocol) or TFTP. Dual image support Provide independent primary and secondary software images for backup while upgrading. User account management Password strength checking and aging feature provides enhanced security to user account administration to the local web management interface. Secure Sockets Layer (SSL) Encrypts all HTTP traffic, secures access to the local browser- based management of the switch. SNMPv1, v2c, and v3 Facilitate management of the switch, as the device can be discovered and monitored from an SNMP management station. Remote monitoring (RMON) Remote monitoring (RMON) provides advanced monitoring and reporting capabilities for statistics, history, alarms and events. RMON data is retrieved from the switch through a network management platform over SNMP. Warranty, Service and Support Aruba Instant On Limited Lifetime Support provides 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is included for the life of the product. Refer to the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. (patro.cz)
Podobné produkty ako Aruba Instant On 1930 48G 4SFP/SFP+ Switch, JL685A , Vention 4-port usb 3.0 hub with power supply 0.15m black (chlbb)I/O ports and slots 48 RJ-45 auto-negotiating 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3af PoE, IEEE 802.3at) 2 SFP+ fixed 1000/10000 SFP+ ports 2 RJ-45 1/10GBASE-T ports Additional ports and slots 1 RJ-45 console port to access limited CLI port Physical characteristics Dimensions 17.32(w) x 16.54(d) x 1.73(h) in (44 x 42 x 4.4 cm) (1U height) Weight 15.43 lb (7 kg) Memory and processor 128 MB flash; Packet buffer size: 3 MB, 1 GB SDRAM Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance 100 Mb Latency < 5 µs 1000 Mb Latency < 5 µs 10 Gbps Latency < 1.5 µs Throughput up to 130.9 Mpps (64-byte packets) Routing/Switching capacity 176 Gbps Routing table size 32 entries (IPv4), 32 entries (IPv6) MAC address table size 16384 entries Reliability MTBF (years) 26.8 Environment Operating temperature 32°F to 113°F (0°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Nonoperating/Storage temperature -40°F to 158°F (-40°C to 70°C) Nonoperating/Storage relative humidity 5% to 95%, noncondensing Altitude up to 16,404 ft (5 km) Acoustic Low-speed fan: 47.3 dB, High-speed fan: 50.0 dB; ISO 7779 Dual speed fan Electrical characteristics Frequency 50/60 Hz Voltage 100 - 240 VAC, rated (depending on power supply chosen) Maximum power rating 470 W PoE power 370 W PoE+ Notes Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. PoE power is the power supplied by the internal power supply. It is dependent on the type and quantity of power supplies and may be supplemented with the use of an external power supply (EPS). When supplemented with the use of an HP RPS1600 Redundant Power System, up to 800W of PoE+ can be supplied. Unit max. power consumption with RPS is 910W. Safety UL 60950; IEC 60950-1; EN 60950-1; GB 4943.1 Emissions FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; EN 55024; EN 61000-3-2 2000, 61000-3-3; ICES-003 Class A Management IMC - Intelligent Management Center; Limited command-line interface; Web browser; SNMP Manager; HTTPS; RMON1; FTP;; Supported by HP IMC and generic SNMP management platforms. Refer to documentation for MIB support details. Notes Transceivers under accessories are recommended versions. Here is the list of fully supported transceivers. 10G SFP+: JD092B, JD093B, JD094B, JG234A, J9150A, J9151A, J9152A, J9153A. GE SFP: JD118B, JD119B, JD089B, J4858C, J4859C, J8177C. Services Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office. (tonerpartner.cz)
Podobné produkty ako HPE OfficeConnect 1950 24G 2SFP+ 2XGT PoE+ Switch + , Vention 4-port usb 2.0 hub with power supply 1m black (chmbf)Klíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE a až 370 W PoE třídy 4 pro podporu zařízení IoT. Kompaktní 12portový model bez ventilátoru pro tichý chod. Flexibilita správy s podporou Aruba Central, snadno použitelné webové grafické rozhraní, rozhraní CLI a Aruba NetEdit. Jednoduché nasazení s funkcí Zero Touch Provisioning. Připravenost na softwarovou definici s rozhraními REST API. Zjednodušení přidávání, přesunů a změn pomocí bezbarvého systému portů. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti. Specifications Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A) Description 48x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports Supports PoE Standards IEEE 802.3af, 802.3at 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (500W) Up to 370W of Class 4 PoE Power Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 30.48 cm (1.73" x 17.4" x 12.0") Configuration Weight 5.02 kg (11.07 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 176 Gbps Model Throughput Capacity 98.6 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.9 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 4.3 Bel Sound Pressure, LpAm (Bystander) = 29.8 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 4.9 A / 2.4 A Power Consumption (230 VAC) Idle: 30.6W Max Power (w/o PoE): 45W Max Power (w/ PoE): 480W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6100 48G Class4 PoE 4SFP+ 370W Switch JL675A , First austria fa 5130 náhradní dílyAruba Instant On 1930 48G 4SFP/SFP+ Switch Switch s vysokou kapacitou a výkonem Aruba Instant On 1930 48G 4SFP/SFP+ Switch je vybaven 48 RJ-45 autosensing 10/100/1000 porty a 4 SFP+ 1/10GbE porty. Fyzické charakteristiky Switch má rozměry 17.42(w) x 11.12(d) x 1.73(h) in a váží 6.91 lb. Výkonný procesor a dostatek paměti Procesor ARM Cortex-A9 pracuje na frekvenci 800 MHz. Switch je vybaven 512 MB SDRAM a 256 MB flash paměti. Vysoký výkon 100 Mb latency: < 4.5 uSec 1000 Mb latency: <2.2 uSec 10000 Mb latency: <1.2 uSec Throughput (Mpps): 130.95 Mpps Capacity: 176 Gbps Provozní podmínky Switch je navržen pro provoz v teplotách 32°F do 104°F s relativní vlhkostí 15% až 95%. Elektrické charakteristiky Switch pracuje na frekvenci 50-60 Hz s napětím 100 - 127 / 200 - 240 VAC. Maximální výkon je 36.9 W. Bezpečnost a imunita Switch je certifikován dle UL 60950-1, IEC 60950-1,EN 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60825-1 a dalších. Správa zařízení Zařízení lze spravovat přes Aruba Instant On Cloud, webový prohlížeč nebo SNMP Manager. Montáž Switch lze montovat do 19" racku, na stůl, na zeď nebo pod stůl. Transceivery Switch podporuje řadu transceiverů, včetně Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver a dalších. (tonerpartner.cz)
Podobné produkty ako 20 x Aruba Instant On 1930 48G 4SFP/SFP+ Switch , Elektrobock pt712-ei + čidlo podlahy (0616)HPE X240 10G SFP+ 1.2m DAC Remanufactured Cable (patro.cz)
Podobné produkty ako HPE X240 10G SFP+ 1.2m DAC HP RENEW Cable JD096CR, JD096CR , Yato sekáč vzduchový 1/4" 110l/min (5906083909900)HPE 3600 Switch SFP Stacking Kit (patro.cz)
Podobné produkty ako HPE 3600 Switch SFP Stacking Kit - výprodej, JD324B//romoAruba 6100 24G 4SFP+ Switch (JL678A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting Standards And Protocols (Applies to all products in series) RFC 1591 DNS (client) SSHv1/SSHv2 Secure Shell IEEE 802.1D MAC Bridges IEEE 802.1p Priority IEEE 802.1Q VLANs IEEE 802.1s Multiple Spanning Trees IEEE 802.1w Rapid Reconfiguration of Spanning Tree IEEE 802.3 Type 10BASE-T IEEE 802.3ab 1000BASE-T IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.3at Power over Ethernet IEEE 802.3az Energy Efficient Ethernet IEEE 802.3x Flow Control RFC 768 UDP RFC 783 TFTP Protocol (revision 2) RFC 792 ICMP RFC 793 TCP RFC 826 ARP RFC 1350 TFTP Protocol (revision 2) RFC 2131 DHCP client RFC 4330 Simple Network Time Protocol (SNTP) v4 RFC 951 BOOTP (VLAN 1 Only) RFC 1542 BOOTP Extensions (VLAN 1 only) IGMPv2/IGMPv3 IGMP/MLD Snooping RFC 1981 IPv6 Path MTU Discovery RFC 2460 IPv6 Specification RFC 2925 Remote Operations MIB (Ping only) RFC 3315 DHCPv6 (client only) RFC 3513 IPv6 Addressing Architecture RFC 3596 DNS Extension for IPv6 RFC 3176 sFlow RFC 4022 MIB for TCP RFC 4113 MIB for UDP (Partially) RFC 4251 SSHv6 Architecture RFC 4252 SSHv6 Authentication RFC 4253 SSHv6 Transport Layer RFC 4254 SSHv6 Connection RFC 4293 MIB for IP RFC 4419 Key Exchange for SSH RFC 4443 ICMPv6 RFC 4861 IPv6 Neighbor Discovery RFC 4862 IPv6 Stateless Address Auto-configuration RFC 1213 MIB RFC 1493 Bridge MIB RFC 2674 802.1p and IEEE 802.1Q Bridge MIB (Partial support. MIB objects supported: ieee8021BridgeBasePort, ieee8021BridgeBasePort, ieee8021BridgePortMrpJoinTime, ieee8021BridgePortMrpLeaveTime, ieee8021BridgePortMrpLeaveAllTime) RFC 2737 Entity MIB RFC 2863 The Interfaces Group MIB IEEE 802.1AB Link Layer Discovery Protocol (LLDP) RFC 1098 A Simple Network Management Protocol (SNMP) ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED) SNMPv1/v2c/v3 RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events) RFC 1098 A Simple Network Management Protocol (SNMP) RFC 2474 DiffServ precedence, with 2/4/8 queues per port RFC 2475 DiffServ Architecture RFC 2597 DiffServ Assured Forwarding (AF) RFC 2598 DiffServ Expedited Forwarding (EF) IEEE 802.1X Port Based Network Access Control RFC 1492 TACACS+ RFC 2138 RADIUS Authentication RFC 2866 RADIUS Accounting Secure Sockets Layer (SSL) (patro.cz)
Podobné produkty ako Aruba 6100 24G Class4 PoE 4SFP+ 370W Switch No Loc, JL678AAruba Instant On 1930 48G Class4 PoE 4SFP/SFP+ 370W Switch Produktový kód: JL686B Porty a sloty 48 RJ-45 autosensing 10/100/1000 Class 4 PoE ports 4 SFP+ 1/10GbE ports Physické charakteristiky Dimensions: 17.42(w) x 12.7(d) x 1.73(h) in Weight: 10.12 lb (4.59 kg) Procesor ARM Cortex-A9 @ 800 MHz Paměť a Flash 512 MB SDRAM 256 MB flash Performance 100 Mb latency: < 4.5 uSec 1000 Mb latency: <2.2 uSec 10000 Mb latency: <1.2 uSec Throughput (Mpps): 130.95 Mpps Capacity: 176 Gbps Environment Operating temperature: 32°F to 104°F (0°C to 40°C) Operating relative humidity: 15% to 95% @ 104°F (40°C) Elektrické charakteristiky Frequency: 50-60 Hz AC voltage: 100 - 127 / 200 - 240 VAC Maximum power rating: 465.6W Idle power: 38.3W PoE power: 370 W Class 4 PoE Bezpečnost UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Montáž Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A ) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) (tonerpartner.cz)
Podobné produkty ako Aruba Instant On 1930 48G Class4 PoE 4SFP/SFP+ 370W SwitchAruba Instant On 1960 12XGT 4SFP+ Switch Kód produktu: JL805A EAN: 190017521770 Specifikace: Porty: 12 RJ-45 autosensing 100/1000/10GBASE-T ports SFP+ porty: 4 SFP+ 10GbE ports Rozměry a hmotnost: Rozměry: 350.5(d) x 442.5(w) x 43.95(h) mm Hmotnost: 9.6 lb (4.3 kg) Výkon: Procesor: Single Core ARMv7 Cortex-A9 @2Ghz Latence: 100 Mb Latency < 7.4 uSec, 1000 Mb Latency < 4.2 uSec, 10000 Mb Latency < 1.1 uSec Průtok: 238 Mpps Kapacita: 320 Gbps Tabulka velikosti: Statické záznamy: 512 IPv4/IPv6 Velikost tabulky MAC adres: 16,000 entries Bezpečnost: Normy: EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, EN/IEC 62368-1, 2nd. & 3rd. Ed., UL 62368-1, 2nd. & 3rd. Ed., CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed., EN/IEC 60825-1:2014 Class 1 Elektrické charakteristiky: Frekvence: 50Hz/60Hz AC napětí: 100-127VAC / 200-240VAC Proud: 1.3A/0.4A Maximální výkon: 100-127V: 130W 200-220V: 160W Správa zařízení: Aruba Instant On Cloud; Web browser; SNMP Manager Možnosti montáže: Montáž v EIA-standard 19 in. telco rack nebo skříni Podpora montáže na stůl Podpora montáže na zeď s porty směřujícími nahoru nebo dolů Podporované transceivery: Aruba 1G SFP LC SX 500m MMF Transceiver (J4858D) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba 1G SFP RJ45 T 100m Cat5e Transceiver (J8177D) Aruba 10G SFP+ LC SR 300m MMF Transceiver (J9150D) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) Aruba 10G SFP+ to SFP+ 1m DAC (J9281D) Aruba 10G SFP+ to SFP+ 3m DAC (J9283D) (tonerpartner.cz)
Podobné produkty ako Aruba Instant On 1960 12XGT 4SFP+ Switch (12RJ45 100/1000/10GBASE-T 4SFP+ fixed 1000/10000 SFP+)Aruba Instant On 1930 48G Class4 PoE 4SFP/SFP+ 370W Switch (JL686A). I/O Ports and Slots 48 RJ-45 autosensing 10/100/1000 Class 4 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only + 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 12.7(d) x 1.73(h) in (44.25 x 32.26 x 4.39 cm) (1U height) Weight 9.97 lb (4.52 kg) CPU ARM Cortex-A9 @ 800 MHz Memory And Flash 512 MB SDRAM 256 MB flash Packet Buffer 1.5 MB Performance 100 Mb latency < 4.5 uSec 1000 Mb latency <2.2 uSec 10000 Mb latency <1.2 uSec Throughput (Mpps) 130.95 Mpps Capacity 176 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 114 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic Pressure: 40.6 Power: 63.2 dB Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current 5/2.5 A Maximum power rating 460.0 W Idle power 34.5 W PoE power 370 W Class 4 PoE Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A ) Aruba 1G SFP LC LX 10km SMF XCVR (J4859D) Aruba 1G SFP RJ45 T 100m Cat5e XCVR (J8177D) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) High-performance, smart-managed switches designed with small businesses in mind Whether you own a cafe, a design firm or a tech startup, a reliable and secure network plays a critical role in the success of your business. And you need a network solution that gives you peace of mind, allowing you to focus on growing your business instead of managing problems with your network. Aruba Instant On makes it easy to keep network users happy, mobile and IoT devices connected, and your network secure. The Aruba Instant On 1930 switches features advanced, smart-managed, fixed- configuration Gigabit switches designed for small businesses that are easy-to-deploy and affordable. They're made to handle today's bandwidth-heavy applications like voice and video conferencing, enabling consistent connectivity to enhance performance. Using either the Instant On mobile app or the cloud-based web portal, you can quickly set up, monitor and manage the 1930 switch series from anywhere at any time. What's more, up to 30 W PoE power delivery is available out-of-the-box for your class 4 PoE devices, like access points, surveillance cameras and VoIP phones, all easily managed from the same platform. Built-in security features protect your network from unauthorized access by allowing you to segment traffic and define access to each area of the network. And all of this is included in the price of the hardware - there are no hidden subscription or licensing fees. Key Features Smart-managed layer 2+ Ethernet switch series ready to deploy in 8-, 24-and 48-port for non-PoE and Class 4 PoE (i.e. PoE+) models PoE to power APs and IoT devices like IP phones, surveillance cameras and door locks Two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models to eliminate traffic bottlenecks across your network Security controls let you define access in each area of your network, keeping your business data safe Convenient mobile app and web- based GUI for set up, management and troubleshooting. Standard Features Simplicity at its best Plug-and-play switches that work together with Instant On APs right out of the box Mobile app to easily setup, monitor and manage your network Security you can count on Protect your network from unauthorized access with IEEE 802.1X and VLANs Automatic denial-of-service (DOS) monitors and protects the network against malicious attacks We've got you covered No extra licensing or subscription fees Industry-leading limited lifetime warranty and support. The Instant On Differentiators Easy setup and management The Aruba Instant On mobile app allows you to set up, manage, and monitor Instant On switches and access points directly from your phone. Within the app, you get guided step-by-step instructions to install Instant On devices to get your network up and running quickly - no technical expertise required. And cloud-based access allows you to access the network from anywhere, at any time. Non-intrusive, aesthetic design Aruba Instant On switches are designed to complement the sleek and clean look of the Instant On access points, and to blend discreetly into your site's environment. The 8-port models, as well as the 24- and 48-port non PoE+ models, are fan-less, making them ideal for quiet office deployments. High performance with flexible options The series consists of four (4) Class 4 PoE (PoE+) switches, and three (3) non-POE switches including 8- 24- and 48-port Gigabit Ethernet switches. The two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models, ensure high performance and eliminate traffic bottlenecks across the network. Customizable features include basic Layer 2 features like VLANs and link aggregation, as well as advanced features such as Layer 3 IPv4 static routing, ACLs, and Spanning Tree Protocols, and IPv6 Host mode. Optimized user experience The Aruba Instant On mobile app provides common workflows for Instant On switches and access points making it easier to configure, monitor and manage your network remotely without the need for additional hardware like cloud keys or VPN. You can also update firmware on your Instant On devices directly from the cloud whenever you want, from wherever you are. Site inventory The site inventory feature on the Instant On mobile app shows you all switches and AP's on a single screen, allowing you to quickly identify non-functioning devices and troubleshoot accordingly. Multi-site management The cloud-hosted web interface and mobile app make it easy to manage multiple sites, multiple networks, distributed deployments and multi-tenant deployments. Each site is logically separated and has its own configuration, statistics, guest portal, and admin read/write privileges. Built-in security Built-in security features protect your network from external threats by blocking malware attacks and keeping unauthorized users off the network. Network traffic can be filtered and access restricted based on MAC and IP address. No hidden fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry leading limited lifetime warranty are also included, along with chat support for the life of the product. Management Cloud-based management for entire network The cloud-hosted web interface and mobile app make it easy to manage networks with Instant On APs and Switches. Simple local web GUI management For management of individual switches, the intuitive Web GUI makes management simple, even for non-technical users. Supports up to five (5) HTTP and HTTP Secure (HTTPS) sessions. Firmware update Provides notification of the latest firmware with the ability to schedule update at a preferred time through Instant On mobile app and cloud-based web portal. Default DHCP client mode Allows the switch to be directly connected to a network, enabling plug-and-play operation. In the absence of a DHCP server on the network, the switch falls back to the static address 192.168.1.1. Port mirroring Enables traffic on a port or VLAN to be simultaneously sent to a network analyzer for monitoring. Event logging and alerts Provides detailed information for problem identification and resolution. Account management Allows administrators to add, modify, delete and transfer management accounts, passwords for secure access to Instant cloud mngmnt solution. Locator LED Allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches. Quality of Service (QoS) Traffic prioritization Provides time-sensitive packets (like VoIP and video) with priority over other traffic based on DSCP or IEEE 802.1p classification. IEEE 802.1p/Q VLAN tagging Delivers data to devices based on the priority and type of traffic; supports IEEE 802.1Q. Class of Service (CoS) Sets the IEEE 802.1p/DSCP priority to queue mapping (4 queues). Supports strict priority queuing (SP) or weighted round robin (WRR) queuing. SP and WRR queuing can be configured on individual switch ports. Advanced classifier based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information. Access Switching SFP/SFP+ fiber connectivity Provides fiber connections for uplinks and other connections across longer distances than copper cabling can support. SFP ports are in addition to available copper Ethernet ports, providing a higher total number of available ports. Two (2) SFP 1G ports available on 8-port models and four (4) SFP+ 1G/10G ports on 24-/48 port models. Ethernet Alliance Certified Class 4 PoE (PoE+; IEEE 802.3at) Provides up to 30 W per port, which allows support of the class 4 PoE (i.e. PoE+) capable devices such as video IP phones, wireless access points, and advanced pan/tilt/zoom security cameras, as well as any 15.4 W IEEE 802.3af-compliant end device; mitigates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. Auto-PoE power configuration The switch automatically assigns the required power to a port for a PD device based on Link Layer Discovery Protocol (LLDP). PoE power allocation Support multiple methods (LLDP-MED automatic, class of PoE, or usage-based) to allocate PoE power for more efficient energy savings. Auto MDI/MDI-X Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports. Network Security TPM-based security Includes a Trusted Platform Module (TPM) for secure hardware- based generation and storage of cryptographic keys used for secure connection to the Instant On cloud portal. IEEE 802.1Q VLAN support Support for up to 256 VLANs with a VLAN ID range of 2-4093. IEEE 802.1X access control Authentication of network users on a per port basis prior to permitting network access. Port authentication includes RADIUS assigned VLAN, dynamic VLAN creation, guest VLAN or into an unauthenticated VLAN. Automatic denial-of-service protection Monitors for malicious attacks and protects the network by blocking the attacks. Packet storm protection Protects against unknown unicast, broadcast and multicast storms with user-defined thresholds. RADIUS The switch supports RADIUS authentication with primary and backup server configuration. RADIUS accounting A robust set of attributes and statistics are available for collecting information from the switch. Management VLAN ID Provides secure management access to administrators in the specified VLAN. Link Flap prevention Minimizes the network disruption by automatically detecting and disabling ports that experience link flap events. Performance and Efficiency Energy Efficient Ethernet (EEE) Compliant with IEEE 802.3az standard requirements to save energy during periods of low data activity. Auto-port shut down The switch saves power by automatically shutting down power to inactive ports. Power is restored on a port upon link detection. Energy savings status The switch provides an estimated cumulative energy savings due to green Ethernet features being enabled. Energy-efficient cooling Includes variable speed fans operating only at speed necessary to maintain operating temperature to reduce excess noise + power consumption. Fan-less operation Fan-less design for 8-port models, 24- and 48-port non-PoE models, making the switches ideal for office deployments. Switching Features IEEE 802.3x Flow control Provides a flow-throttling mechanism propagated through the network to prevent packet loss at a congested node. Spanning Tree Protocol (STP) Supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP on local web). Loop protection If the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms. BPDU filtering Drops BPDU packets when STP is enabled globally but disabled on a specific port. Jumbo frame support Supports up to 9216 bytes frame size to improve the performance of large data transfers. IGMP snooping v1/v2 Improves network performance through multicast filtering, instead of flooding traffic on all ports. Link aggregation Groups together multiple ports up to a maximum of eight (8) ports per trunk automatically using Link Aggregation Control Protocol (LACP), or manually, to form a high-bandwidth connection to the network backbone that helps prevent traffic bottlenecks. The 8-port models support 4 trunks, 24-port models support 8 trunks, and 48-port models support 16 trunks. LLDP/LLDP-MED (Media Endpoint Discovery) Defines standard extension of LLDP that stores values for parameters suchas QoSand VLAN for autoconfiguration of netw devices such as IPphones. Address Resolution Protocol (ARP) The ARP table displays all of the IP addresses that have been resolved to MAC addresses, either dynamically or through static entry configuration. Features Accessed Through Local Web-Management Interface Static IPv4 routing Supports manual routing configuration of up to 32 static routes. Auto-voice VLAN Recognizes IP phones and automatically assigns voice traffic to dedicated VLAN for IP phones. PoE scheduling A PoE scheduler provides the ability to define the hours of PoE power being supplied to a group of switch ports based on a 24-hour day. The scheduler enables the flexibility to select individual days of a week as well as reccurrence on a weekly basis with a start and end date. Access Control Lists (ACLs) Enables network traffic filtering by creating an ACL, adds rules and matches criteria to an ACL, and applies the ACL to permit or deny on one or more interfaces or a VLAN. Supports 50 inbound IPv4 and MAC ACLs with up to 480 ACEs. IPv6 host Enables switches to be managed and deployed at the IPv6 network's edge. Rate limiting Sets and enforces per-port ingress traffic limits based on percentages or packets per second. ARP Attack prevention Dynamic ARP protection blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data. DHCP snooping Provides network security by filtering untrusted DHCP messages. Port security Ports in a port isolation group are restricted from forwarding Layer 2 traffic between ports in that group, providing data privacy and security. SCP and TFTP file transfer Provides different mechanisms for secure file transfer through SCP (Secure Copy Protocol) or TFTP. Dual image support Provide independent primary and secondary software images for backup while upgrading. User account management Password strength checking and aging feature provides enhanced security to user account administration to the local web management interface. Secure Sockets Layer (SSL) Encrypts all HTTP traffic, secures access to the local browser- based management of the switch. SNMPv1, v2c, and v3 Facilitate management of the switch, as the device can be discovered and monitored from an SNMP management station. Remote monitoring (RMON) Remote monitoring (RMON) provides advanced monitoring and reporting capabilities for statistics, history, alarms and events. RMON data is retrieved from the switch through a network management platform over SNMP. Warranty, Service and Support Aruba Instant On Limited Lifetime Support provides 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is included for the life of the product. Refer to the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. (patro.cz)
Podobné produkty ako Aruba Instant On 1930 48G Class4 PoE 4SFP/SFP+ 370W Switch, JL686AAruba 6000 12G PoE Class4 + 2x1GbE 2x1GSFP 139W Switch R8N89AR RENEW Produktový kód: 726221 Specifikace Počet portů: 12x 10/100/1000BASE-T, 2x 1G SFP, 2x 1GbE Podpora PoE standardů: IEEE 802.3af, 802.3at Porty: 1x USB-C Console, 1x USB Type-A Host Zdroj energie: Pevný, až 139W Class 4 PoE Technické parametry Procesor: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť: 4 GB DDR3, 16 GB eMMC Switchovací kapacita: 32 Gbps Průchozí kapacita: 23.8 Mpps Průměrná latence: 1 Gbps: 2.3 µSec IPv4 Host Table (ARP): 1,024 IPv6 Host Table (ND): 512 IPv4 Unicast Routes: 512 IPv6 Unicast Routes: 512 MAC Table Capacity: 8,192 Provozní podmínky Provozní teplota: 32°F to 113°F (0°C to 45°C) Vlhkost při provozu: 15% to 95% at 104°F (40°C) non-condensing Maximální provozní výška: 10000 feet (3 km) Maximální neoperační výška: 15000 feet (4.6 km) Energetické nároky Frekvence: 50 / 60 Hz Napětí: 100-127 VAC / 200-240 VAC Proud: 1.8 A / 0.9 A Spotřeba (230 VAC): idle: 16W, Max Power (w/o PoE): 21.9W, Max Power (w/ PoE): 170W Bezpečnostní a emisní normy Safety: UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions: VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Montáž Montuje se v EIA-standardním 19-palcovém telco racku nebo skříni (k dispozici rack-mounting kit), horizontální montáž na povrch, montáž na zeď. (tonerpartner.cz)
Podobné produkty ako HPE Aruba Networking CX 6000 12G Class4 PoE 2G/2SFP 139W Switch R8N89AR RENEWHPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit (patro.cz)
Podobné produkty ako HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit, 865414-B21HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit (patro.cz)
Podobné produkty ako HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit, P38995-B21HPE 500W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit (patro.cz)
Podobné produkty ako HPE 500W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit pro G10, 865408-B21(tonerpartner.cz)
Podobné produkty ako Aruba Instant On 1960 24G PoE (20pClass4 + 4pClass6) 2XGT 2SFP+ 370W Switch RENEW JL807AAruba 2930F 24G 4SFP+ Switch Přehled Řada přepínačů Aruba 2930F je určena pro zákazníky, kteří vytvářejí digitální pracoviště optimalizovaná pro mobilní uživatele s integrovaným a bezdrátovým přístupem. Tyto základní přístupové přepínače 3. vrstvy lze snadno nasadit a spravovat pomocí pokročilých nástrojů pro správu zabezpečení a správu sítě, jako je Aruba ClearPass Policy Manager a Aruba AirWave. Výkonný Aruba ProVision ASIC přináší výkon a podporu nejnovějších aplikací SDN s budoucí programovatelností pro aplikace zítřka. 2930F podporuje 10GbE uplink, PoE +, robustní QoS, RIP Routing, Access OSPF a IPV6 bez nutnosti licencování softwaru. Řada přepínačů Aruba 2930F nabízí pohodlné a cenově výhodné řešení pro přepínání přístupu, které lze rychle nastavit pomocí funkce Zero Touch Provisioning a vestavěných 10GbE uplinků. Robustní základní sada funkcí vrstvy 3 zahrnuje omezenou záruku na dobu životnosti. - Management: Fully Managed - Layer 3 Dynamic: L2 switching / L3 Static routing / RIP routing - 24x 10/100/1000 RJ45 portů + 4x SFP+ 1/10GbE porty - Aruba ClearPass Policy Manager and Aruba Airwave - Doživotní záruka! - Oprava výměnou následující pracovní den! - Rozsáhlá síť servisních středisek HP v ČR a na Slovensku (patro.cz)
Podobné produkty ako Aruba 2930F 24G 4SFP+ Swch, JL253AAruba Instant On 1960 Switch Model: Aruba Instant On 1960 8p (1G Class 4 PoE) 4p (SR1G/2.5G Class 6 PoE) 2p (10GBASE-T 2p SFP+) 480W Switch EAN: 190017628400 Popis produktu Aruba Instant On 1960 Switch je výkonný a spolehlivý switch, který přináší vysokou propustnost a pokročilé funkce pro malé a střední podniky. Vlastnosti 8 portů 1G Class 4 PoE 4 porty SR1G/2.5G Class 6 PoE 2 porty 10GBASE-T 2 porty SFP+ Výkon 480W Výhody Aruba Instant On 1960 Switch nabízí vysokou propustnost a flexibilitu, díky které je ideální pro malé a střední podniky, které potřebují rychlou a spolehlivou síť. Dodávka Switch je dodáván s napájecím kabelem a uživatelskou příručkou. (tonerpartner.cz)
Podobné produkty ako HPE Networking Instant On Switch 8p Gigabit CL4 4p SR2.5G CL6 PoE 2p 10GBT 2p SFP+ 480W 1960HPE X240 10G SFP+ SFP+ 3m DAC Cable (patro.cz)
Podobné produkty ako HPE X240 10G SFP+ SFP+ 3m DAC Cable, JD097CMikroTik Cloud Smart CSS326-24G-2S+RM Zcela nová řada Cloud Smart Switch s 24x Gbit porty a 2x SFP + porty. Ideální náhrada za rack switch. Velkou předností je podpora 10 Gbps rozhraní a jednoduché rozhraní SwOS. Dodává se v hliníkovém indoor case v provedení rack 1U. Ideální řešení, jak pro poskytovatele internetu, tak i pro firmy. Největší předností je 24 plně gigabitových portů. V případě přivedení optické trasy je switch vybaven dvěma SFP+ porty pro optické moduly. Cloud Smart Switch je v provedení 1U, lze je tedy namontovat přímo do racku. Součástí Cloud Smart Switch je operační systém SwOS. V balení jsou L profily pro uchycení do racku. ZÁKLADNÍ SPECIFIKACE Porty: 24 x RJ-45 10/100/1000 Mbps, 2 x SFP+ Operační systém: SwOS Paměť: 2 MB Napájení: 1 x 10-30 V DC, 1 x pasivní PoE 10-30 V Rozměry: 440 x 144 x 44 mm (patro.cz)
Podobné produkty ako MikroTik Cloud Smart Switch CSS326, 24x Gbit LAN, 2x Gbit SFP port, CSS326-24G-2S+RM1x video stativ Walimex pro EI-9901, 138 cm s možností naklápění, 2 rychle vyměnitelné desky a praktické přepravní pouzdro (conrad.cz)
Podobné produkty ako Trojnohý stativ Walimex Pro EI-9901, 1/4palcové, min./max.výška 69 - 138 cmPřed objednáním si, prosím, ověřte aktuální dostupnost (není-li produkt skladem u eD).Podmínky na RENEW trhu se mění rychle. Nelze garantovat dostupnost ani cenu, pokud zboží nemáme skladem.sHP Power Supply Kit 500W Flex Slot Platinum Hot Plug G9 720478-B21 HP RENEW (patro.cz)
Podobné produkty ako HP Power Supply Kit 500W Flex Slot Platinum Hot Plug G9 720478-B21 HP RENEW, 720478R-B21Aruba 2930F 48G 4SFP Swch JL260A HP RENEW (tonerpartner.cz)
Podobné produkty ako Aruba 2930F 48G 4SFP Swch JL260A HP RENEWCBS220-8T-E-2G - Cisco Business 220 Ethernet Switch Řada Cisco Business 220 jsou cenově dostupné inteligentní přepínače se snadným použitím, zabezpečením a spolehlivostí pro sítě podnikové třídy. Díky intuitivnímu palubnímu panelu, možnostem napájení přes Ethernet (u vybraných modelů) a přizpůsobitelným funkcím poskytují tyto přepínače spolehlivou obchodní síť v rámci vašich rozpočtových parametrů. Pokud potřebujete síť na špičkové úrovni a cena je nejvyšší prioritou, nabízí řada Cisco Business 220 vynikající řešení. Spolehlivost a výkon - Přepínače byly testovány, aby poskytovaly vysokou dostupnost a výkon, který uživatelé očekávají. Přepínače zrychlují časy přenosu souborů, udržují důležité obchodní aplikace k dispozici a pomáhají vašim zaměstnancům rychleji reagovat na zákazníky i na sebe navzájem. Zabezpečení sítě - Rozsáhlé Acces Control Lists (ACL) mohou omezit citlivé části sítě před neoprávněnými uživateli a chránit před síťovými útoky. Prevence útoků typu Denial-of-Service (DOS) pomáhá prodloužit dobu provozu v případě síťového útoku. Optimální energetická účinnost - Přepínače jsou navrženy s podporou Energy Efficient Ethernet (IEEE 802.3az) a Energy Detect u všech modelů, stejně jako u vybraných modelů bez ventilátorů. Tyto návrhy vám pomohou ušetřit provozní náklady a snížit vaši ekologickou stopu. Snadná konfigurace a nasazení - Jednoduchá a intuitivní webová rozhraní umožňují uživatelům bez rozsáhlých odborných znalostí IT konfigurovat, spravovat a odstraňovat problémy s přepínači během několika minut. Průvodci konfigurací zjednodušují nejběžnější konfigurační úlohy a poskytují nástroj pro nastavení a správu sítě komukoli. PARAMETRY Přepínací kapacita: 20 Gbps Porty: 8x Gigabit ethernet RJ-45, 2x Gigabit ethernet SFP Tabulka Mac adres: až 8 192 MAC adres Seskupení portů: až 8 portů na skupinu VLAN: podpora až 256 virtuálních lokálních sítí současně Rámec Jumbo: až 9 216 PoE: Ne Tlačítko: Reset Typ kabelu: Nestíněný kroucený pár (UTP) kategorie 5 nebo lepší pro 10BASE-T / 100BASE-TX LED: System, Akce, Rychlost Flash: 64 MB CPU memory: 256 MB Vyrovnávací paměť paketů: 4.1 Mb Rozměry: 279 x 170 x 44 mm Hmotnost: 1.16 kg Napájení: externí 100-240 V, 50-60 Hz Certifikace: UL, CSA, CE, FCC, C-tick Operační teplota: 0 - 50°C Skladovací teplota: -20°C až +70°C Provozní vlhkost: 10% až 90% Spotřeba energie: 110V=5,7W; 220V=5,9W Počet ventilátorů: Žádný MTBF (hodin): 1,489,560 Obsah balení: - Cisco Business 220 switch - Napájecí kabel nebo adaptér - Montážní sada - Instalační příručka Odkaz na web výrobce: https://www.cisco.com/c/en/us/products/collateral/switches/business-220-series-smart-switches/datasheet-c78-744915.html (patro.cz)
Podobné produkty ako CISCO Business Switching CBS220 Smart 8-port Gigabit 2x1G SFP uplink external power supply, CBS220-8T-E-2G-EUKlíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE. Kompaktní 12portový model bez ventilátoru pro tichý chod. Flexibilita správy s podporou Aruba Central, snadno použitelné webové grafické rozhraní, rozhraní CLI a Aruba NetEdit. Jednoduché nasazení s funkcí Zero Touch Provisioning. Připravenost na softwarovou definici s rozhraními REST API. Zjednodušení přidávání, přesunů a změn pomocí bezbarvého systému portů. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti. Specifications Aruba 6100 48G 4SFP+ Switch (JL676A) Description 48x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (65W) Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 24.74 cm (1.73" x 17.4" x 9.74") Configuration Weight 3.42 kg (7.54 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 176 Gbps Model Throughput Capacity 98.6 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.9 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 48G 4SFP+ Switch (JL676A) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.6 Bel Sound Pressure, LpAm (Bystander)= 24.6 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.8 A / 0.5 A Power Consumption (230 VAC) Idle: 20.6W Max Power (w/o PoE): 44.2W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 48G 4SFP+ Switch (JL676A) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting (patro.cz)
Podobné produkty ako Aruba 6100 48G 4SFP+ Switch, JL676A1x video stativ Walimex pro EI-717, 133 cm s vyklápěčkou, rychlou a praktickou přepravní taš (conrad.cz)
Podobné produkty ako Trojnohý stativ Walimex Pro EI-717, 1/4palcové, 3/8palcové, min./max.výška 64 - 133 cm, černá