ram mounts suction base with diamond holder

RAM Mounts Suction Base with Diamond Holder (Trapezoid) - Screw Cap, Diameter 83.82 mm, incl. Screw Set

Objev podobné jako RAM Mounts Suction Base with Diamond Holder

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-CAU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This ... Unknown localization key: "more"

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-1AU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-A 1.1 (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support ... Unknown localization key: "more"

Objev podobné jako RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

svítidlo Bastos 2101 bronzová
plastový vyvýšený záhon BASE WOODY
záhon BASE WOODY 75,6x25x75,6 cm
záhon BASE WOODY Prosperplast
záhon BASE WOODY antracit
záhon BASE WOODY 75,6 x 25 x 75,6 cm
Frudia Sun Tone Up Base 50g
dívčí mikina GAP V-BAS HERITAGE FZ šedá
zvlhčovač vzduchu do auta Baseus
černá čistička vzduchu Baseus Freshing Breath
kusový koberec Diamond 20701-95 šedý
koberec Diamond pro jedinečný interiér
moderní konferenční stolek Diamond Black
moderní konferenční stolek Diamond Cream
moderní obývací stolek Diamond Oak
SAPHO 1318-19 Diamond dávkovač

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-CAU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product ... Unknown localization key: "more"

Objev podobné jako RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not ... Unknown localization key: "more"

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral & data support is provided by the built-in dual USB-A & RJ45 (ethernet) cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-RJ45AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A & RJ45 (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable ... Unknown localization key: "more"

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & Dual USB-A & RJ45(Ethernet) Conne

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLTU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLTU holder is supplied.

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-1AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible ... Unknown localization key: "more"

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

RAM Mounts Diamond Base Plate (Trapezoid) - 1 Inch B Ball, 2-Bolt AMPS Hole Grid

Objev podobné jako RAM Mounts RAM-B-238U Diamond Base Plate

RAM Mounts Suction Base Set with Diamond Connection - long connecting arm, 2x Diamond base plate (trapezoid), B-ball (1 inch), in a poly bag

Objev podobné jako RAM Mounts RAM-B-166U-C Suction Base Set with Diamond Connection

RAM Mounts Suction Base with Diamond Base Plate (Trapezoid) - Twist Cap, Not Mounted, B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAM-B-224-1U Suction Base with Diamond Base Plate

RAM Mounts Suction Cup with Diamond Base Plate (Trapezoid, Composite) - Twist Cap, Not Mounted, B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-224-1U Suction Cup with Diamond Base Plate

RAM Mounts X-Grip Suction Base Holder for Tablets (10 inches) - B-Ball (1 Inch), Medium Connection Arm

Objev podobné jako RAM Mounts RAM-B-166-UN9U X-Grip Suction Base Holder

RAM Mounts Triple Suction Base with Round Base Plate (AMPS) - Each Twist Cap, Not Assembled, Plastic Plate, C-Ball (1.5"), in Poly Bag

Objev podobné jako RAM Mounts RAP-365-224-1U Triple Suction Base with Round Base Plate

This RAM Mounts GDS Cool-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKF-SAM62CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Includes built-in 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKF-SAM62CPU holder is supplied.

Objev podobné jako RAM Mounts GDS Cool-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Connector

This RAM Mounts GDS Cool-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 & Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKF-SAM62CU: Compatible with GDS hand-stand & more Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 60W Output Voltage: 5-20V @ 3A Transfer Speed: 5Gbps Input Cable Length: ca. 21 cm Includes built-in 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKF-SAM62CU holder is supplied.

Objev podobné jako RAM Mounts GDS Cool-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Power Supply

This RAM Mounts GDS Cool-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKLF-SAM62CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Includes built-in 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKLF-SAM62CPU holder is supplied.

Objev podobné jako RAM Mounts GDS Cool-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Connect

RAM Mounts Suction Base Set with AMPS Connection - Long Connecting Arm, Diamond Base Plate (Trapezoid), Round Base Plate (AMPS), B-Ball (1 Inch), in Polyb

Objev podobné jako RAM Mounts RAM-B-166-C-202U Suction Base Set

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDKLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with keyPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDKLU holder is supplied.

Objev podobné jako RAM Mounts RAM-HOL-HON9PDKLU Form-Fit Holder (with key-locking) for Honeywell RT10

RAM Mounts Composite Suction Base Set with C-Ball (1.5 inches) - Round Base Plate (AMPS), in Poly Bag

Objev podobné jako RAM Mounts RAM-224-3U Composite Suction Base Set

RAM Mounts Suction Base Set with Diamond Connection - Middle Connecting Arm, 2x Diamond Base Plate (Trapezoid), B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAM-B-166U Suction Base Set

RAM Mounts Double Suction Base with Round Base Plate (AMPS) - B-Ball (1 inch), Unmounted

Objev podobné jako RAM Mounts RAM-B-189B-202U Double Suction Base

RAM Mounts Composite Suction Base Set with Diamond Attachment - Middle Connecting Arm, 2x Diamond Base Plate (Trapezoid), B-Ball (1 Inch), in Poly Booty

Objev podobné jako RAM Mounts RAP-B-166U Composite Suction Base Set

RAM Mounts Composite Suction Base Set with Diamond Connection - Short Connection Arm, 2x Diamond Base Plate (Trapezoid), B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-166U-A Composite Suction Base Set

RAM Mounts Composite Suction Base Bracket with X-Grip Retaining Clip for Smartphones up to 82.6 mm Width - B-Ball (1 Inch), Middle Connection Arm (approx. 90 mm)

Objev podobné jako RAM Mounts RAM-B-166-UN7U Composite Suction Base Bracket

RAM Mounts X-Grip Suction Base Bracket for Tablets (7 inches) - B-Ball (1 Inch), Medium Link Arm

Objev podobné jako RAM Mounts RAM-B-166-UN8U X-Grip Suction Base Bracket

RAM Mounts Triple Suction Base with AMPS Holder - each with twist cap, metal plate, in poly bag

Objev podobné jako RAM Mounts Triple Suction Base

RAM Mounts Triple Suction Base with AMPS Holder - each screw cap, not mounted, plastic plate, in poly bag

Objev podobné jako RAM Mounts Triple Suction Base

RAM Mounts Composite Cup Holder Base with Rubber Lips - B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-299-4U Composite Cup Holder Base

RAM Mounts Stand with Holder for Round Base Plate - 228 x 228 mm, Screw Set

Objev podobné jako RAM Mounts Stand with Holder

RAM Mounts Swivel Arm with Vertical Tube Base - Arm Length approx. 150 mm, Connecting Arm, Round Base Plate, C-Ball (1.5 inches), in Poly Bag

Objev podobné jako RAM Mounts RAM-VB-110V-2U Swivel Arm with Vertical Tube Base

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PU holder is supplied.

Objev podobné jako RAM Mounts RAM-GDS-DOCKL-ZE20PU GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8")

This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE20PU holder is supplied.

Objev podobné jako RAM Mounts RAM-GDS-DOCK-ZE20PU GDS EZ-Roll'r Holder for Zebra ET40/45 (8")

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-HON12PHU Form-Fit Holder for Honeywell CT40, CT45 & CT47

This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-GDS-DOCK-ZE21PDU GDS EZ-Roll'r Holder for Zebra ET40/45 (10")

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-GDS-DOCKL-ZE20PDU GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8")

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-GE4PDU Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-HON12PDHU Form-Fit Holder for Honeywell CT40, CT45 & CT47

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PLU holder is supplied.

Objev podobné jako RAM Mounts RAM-HOL-HON12PLU Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-HON12PDU Form-Fit Holder for Honeywell CT40, CT45 & CT47

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-GE4PU Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-HON12PHLU Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-GDS-DOCKL-ZE20PD2U GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8")

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-GE4PDKLU Form-Fit Holder (Key-Locking) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-HOL-HON12PDHLU Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the ... Unknown localization key: "more"

Objev podobné jako RAM Mounts RAM-GDS-DOCKL-ZE21PDU GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10")

This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates extended battery packs and the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE2434CPDHU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Heated Pogo-Pins Lockable with key Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm ... Unknown localization key: "more"

Objev podobné jako RAM Mounts GDS Holder (Key-Locking) for Zebra TC2x & TC5x Series in IntelliSkin Protective Sleeve - Heated Pogo-Pins - USB-C & USB-A Connector

This RAM Mounts GDS holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-V12-ZE16CPDU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm Additional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-V12-ZE16CPDU holder is supplied.

Objev podobné jako RAM Mounts GDS Holder for Zebra EC50 & EC55 in IntelliSkin Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates extended battery packs and the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-V12-ZE2434CPDU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm Additional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-V12-ZE2434CPDU holder is supplied.

Objev podobné jako RAM Mounts GDS Holder for Zebra TC2x & TC5x Series in IntelliSkin Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PD2KLU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal Lockable with key Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: 2x ... Unknown localization key: "more"

Objev podobné jako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC & Dual USB-A Connector