ram mounts rap tab kb1 300u keyboard mount

RAM Mounts Keyboard Mount with Rotatable Tablet Connection - Composite

Objev podobné jako RAM Mounts RAP-TAB-KB1-300U Keyboard Mount

RAM Mounts Universal Tab-Tite Mounting Bracket for Panasonic FZ-G2 & FZ-A3 - AMPS Mounts

Objev podobné jako RAM Mounts Universal Tab-Tite Mounting Bracket

RAM Mounts Universal Tab-Lock Bracket (lockable) for Panasonic Toughpad FZ-G1 - AMPS mount, screw set

Objev podobné jako RAM Mounts Universal Tab-Lock Bracket

RAM Mounts Universal Tab-Lock Base (lockable, without end caps) - AMPS mount, screw set

Objev podobné jako RAM Mounts Universal Tab-Lock Base

RAM Mounts RAM-A-CAN II Universal Composite Bracket with Diamond Connection (Trapezoid) - for Vehicle Cup Holders, Base with Rubber Lips, 2x Diamond Base Plate (Trapezoid), Middle Connection Arm

Objev podobné jako RAM Mounts RAP-299-3-B-102U RAM-A-CAN II Universal Composite Bracket

RAM Mounts Composite Mounting Set - 2x Diamond Base Plate (Trapezoid), Middle Connecting Arm, B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-102U Composite Mounting Set

RAM Mounts Composite Set for Cup Holders (Vehicles) - Cup Holder Base, Middle Link Arm, B Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-299-4-201U Composite Set

RAM Mounts Composite Cup Holder Base with Rubber Lips - B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-299-4U Composite Cup Holder Base

RAM Mounts Triple Suction Base with Round Base Plate (AMPS) - Each Twist Cap, Not Assembled, Plastic Plate, C-Ball (1.5"), in Poly Bag

Objev podobné jako RAM Mounts RAP-365-224-1U Triple Suction Base with Round Base Plate

RAM Mounts Tough-Ball with M8 - 1.25 x 10 mm Threaded Pin - C-Ball (1.5 inches), in a poly bag

Objev podobné jako RAM Mounts RAP-379U-M812510 Tough-Ball

RAM Mounts Tough-Claw Retaining Clip (Medium) with Locking Screw - C-Ball (1.5"), Diameter 25.4-40.6mm

Objev podobné jako RAM Mounts RAP-404U Tough-Claw Retaining Clip

RAM Mounts Composite Suction Base Set with Diamond Attachment - Middle Connecting Arm, 2x Diamond Base Plate (Trapezoid), B-Ball (1 Inch), in Poly Booty

Objev podobné jako RAM Mounts RAP-B-166U Composite Suction Base Set

RAM Mounts Composite Suction Base Set with Diamond Connection - Short Connection Arm, 2x Diamond Base Plate (Trapezoid), B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-166U-A Composite Suction Base Set

RAM Mounts Composite Connection Arm with 360° and 180° Swivels - for B-Balls (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-200-2U Composite Connection Arm

RAM Mounts Medium Composite Connection Arm - Approx. 90 mm long, for B-balls (1 inch), in poly bag

Objev podobné jako RAM Mounts RAP-B-201U Medium Composite Connection Arm

RAM Mounts Short Composite Connection Arm - approx. 60 mm long, for B-balls (1 inch), in poly bag

Objev podobné jako RAM Mounts RAP-B-201U-A Short Composite Connection Arm

RAM Mounts Suction Cup with Diamond Base Plate (Trapezoid, Composite) - Twist Cap, Not Mounted, B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-224-1U Suction Cup with Diamond Base Plate

RAM Mounts Composite Track Ball with T-Slot - B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-375U Composite Track Ball

RAM Mounts Tough-Ball with M10 - 1.5 in. x 25 mm Threaded Pin - B-Ball (1 Inch)

Objev podobné jako RAM Mounts RAP-B-379U-M10-JD1 Tough-Ball

RAM Mounts Tough-Ball with M6-1 x 6 mm Threaded Pin - B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-379U-M616 Tough-Ball

RAM Mounts Universal Composite Tough-Clamp (large) - diameter 19.1-28.6 mm, B-ball (1 inch), in poly bag

Objev podobné jako RAM Mounts RAP-B-397-2U Universal Composite Tough-Clamp

RAM Mounts Composite Replacement Ball for Tough-Clamp - B-Ball (1 Inch), in Poly Bag

Objev podobné jako RAM Mounts RAP-B-397BU Composite Replacement Ball

RAM Mounts Tough-Claw Retaining Clip (Small) with Locking Screw - B-Ball (1 inch), Diameter 15.9-29.0 mm

Objev podobné jako RAM Mounts RAP-B-400U Tough-Claw Retaining Clip

RAM Mounts Tough-Claw Retaining Clip (Small) with Locking Screw - B-Ball (1 inch), Additional C-Ball (1.5 Inch), Diameter 15.9-29.0 mm

Objev podobné jako RAM Mounts RAP-BC-400U Tough-Claw

RAM Mounts Composite Mounting Set - 2x Round Base Plate, Middle Connecting Arm, C-Ball (1.5"), in Poly Bag

Objev podobné jako RAM Mounts RAP-101U Composite Mounting Set

RAM Mounts Medium Composite Link Arm for C-Balls (1.5 inches) - Approx. 140 mm long, in poly bag

Objev podobné jako RAM Mounts RAP-201U Medium Composite Link Arm

RAM Mounts Round Composite Base Plate - C-Ball (1.5"), in Poly Bag

Objev podobné jako RAM Mounts RAP-202U Round Composite Base Plate

RAM Mounts Tough-Claw Retaining Clip (Small) with Locking Screw - C-Ball (1.5"), Diameter 15.9-29.0mm

Objev podobné jako RAM Mounts RAP-400U Tough-Claw Retaining Clip

RAM Mounts Tough-Claw Retaining Clip (Large) with Locking Screw - C-Ball (1.5"), Diameter 25.4-55.9mm

Objev podobné jako RAM Mounts RAP-401U Tough-Claw Retaining Clip

RAM Mounts Tough-Claw Retaining Clip (Large) with Locking Screw - B-Ball (1 inch), Diameter 25.4-55.9 mm

Objev podobné jako RAM Mounts RAP-B-401U Tough-Claw Retaining Clip

RAM Mounts Tough-Claw Set - C-Ball (1.5 inches), Tough-Claw Large (Diameter 25.4-55.9 mm), Center Link Arm (approx. 145 mm)

Objev podobné jako RAM Mounts RAP-401-202U Tough-Claw Set

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, Tab S9 & Tab S9 FE in IntelliSkin protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. Data synchronization via the connection is also supported. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM78CU: Compatible with GDS hand-stand Easy insertion and removal Charging function Data synchronization Lockable with key Input Connector: USB-C Power Output: 60W Output Voltage: 5-20V @ 3A Input Cable Length: ca. 35 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM78CU holder is supplied.

Objev podobné jako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7 FE, S7+, S8+, S9 FE+, S9+ & S10+ in IntelliSkin Protective Sleeve - USB-C Power Supp

This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab Active3 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM74-NG:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.This product will not support the "No Battery Mode" function of the Tab Active3. To support "No Battery Mode", see RAM Tough-Case.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM74-NG is supplied.

Objev podobné jako RAM Mounts IntellìSkin Next Gen for Samsung Galaxy Tab Active3 - GDS-Technology

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CP-NFCU: Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CP-NFCU holder is supplied.

Objev podobné jako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM62CP-NFCU: Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM62CP-NFCU holder is supplied.

Objev podobné jako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector

This RAM Mounts GDS IntelliSkin Hard Case protective sleeve is designed for the Samsung Galaxy Tab Active3 & Active5 and offers reliable protection combined with convenient charging functionality. The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use. This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available. Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction. The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move. Product features RAM Mounts RAM-GDS-SKIN-SAM89-HC: Compatible with GDS Docks Holder for Stylus Pen Continued access to camera and buttons Charging function Easy insertion and removal Input Connector: USB-C 2.0 Transfer Speed: Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*) Up to USB 2.0 @ 480Mbps (via External USB-C Port) Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations. Samsung Tab Active5 allows a maximum transfer speed of USB 2.0. This product will not support the "No Battery Mode". To support "No Battery Mode", see RAM Tough-Case. Devices shown are not included in the delivery. Only the RAM-GDS-SKIN-SAM89-HC is supplied.

Objev podobné jako RAM Mounts IntellìSkin Hard Case for Samsung Galaxy Tab Active3 & Active5 - External USB-C Port - GDS-Technology

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-CAU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPT-CAU holder is supplied.

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. The included RAM NFC extender supports the NFC function with a range of up to 30 cm. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, GDS Roto-Mag and side accessory attachments. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKL-NFCU: Compatible with accessories Including RAM NFC-Extender Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKL-NFCU holder is supplied.

Objev podobné jako RAM Mounts Form- Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLT-AU holder is supplied.

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral & data support is provided by the built-in dual USB-A & RJ45 (ethernet) cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-RJ45AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A & RJ45 (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLT-RJ45AU holder is supplied.

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & Dual USB-A & RJ45(Ethernet) Conne

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLTU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLTU holder is supplied.

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-1AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPT-1AU holder is supplied.

Objev podobné jako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Samsung Tab Active Pro and Active4 Pro Tablet in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM57CPKLU: Compatible with GDS hand-stand Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM57CPKLU holder is supplied.

Objev podobné jako RAM Mounts Form-Fit Holder (Key-Locking) for Samsung Tab Active Pro & Active4 Pro - in OEM/RAM Sleeve - USB-C Power Supply

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-1AU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-A 1.1 (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM60CPN-1AU holder is supplied.

Objev podobné jako RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-CAU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM60CPN-CAU holder is supplied.

Objev podobné jako RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C and USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLN-CAU: Compatible with accessories and side accessory attachments Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLN-CAU holder is supplied.

Objev podobné jako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLN-CU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Output Connector: USB-C (Peripheral output - 500mAh) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLN-CU holder is supplied.

Objev podobné jako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Power & Data Connector

This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLNU: Compatible with accessories and side accessory attachments Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLNU holder is supplied.

Objev podobné jako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM76CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM76CPU holder is supplied.

Objev podobné jako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the "No Battery Mode" function.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CD2U holder is supplied.

Objev podobné jako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & Dual USB-A Connector