Kde se rozmanitost setkává s hodnotou - Katalo.cz

HPE Networking Comware Switch 24G SFP w/8G Combo 4SFP+ EI 5140 JL826AR RENEW HPE FlexNetwork 5140 24G SFP 4SFP+ EI Switch (JL826A) I/O ports and slots 16 SFP 100/1000 Mbps ports 8 SFP dual-personality ports - 10/100/1000BASE-T RJ-45 or 100/1000BASE-X Combo Ports 4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Power supplies 2 power supply slots 1 minimum power supply required (ordered separately) Physical characteristics Dimensions 17.32(w) x 14.17(d) x 1.72(h) in (44 x 36 x 4.36 cm) (1U height) Weight 13.23 lb (6kg) Memory and processor 512 MB SDRAM, 256 MB flash; Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (Rack Mount Kit R8M91A sold separately) Performance IPv6 Ready Certified 1000 Mb Latency < 5 µs 10 Gbps Latency < 3 µs Throughput 95 Mpps Routing/Switching capacity 128 Gbps Routing table size 1024 entries MAC address table size 16384 entries Environment Operating temperature 23°F to 113°F (-5°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Non-operating/Storage temperature -40°F to 158°F (-40°C to 70°C) Non-operating/Storage relative humidity 5% to 95%, noncondensing Acoustic Low-speed fan: 41.4 dB, High-speed fan: 47.7 dB; ISO 7779 Electrical characteristics Frequency 50/60 Hz Maximum heat dissipation 102/204 BTU/hr (107.61/215.22 kJ/hr), for AC Powered units. For DC powered units heat dissipation is 130 BTU/hr min, 232 BTU/hr max. Voltage 100 - 240 VAC -48 to -60 VDC Current 5 A Maximum power rating 60 W Idle power 30 W Notes: - Idle power is the actual power consumption of the device with no ports connected. - Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. - Power Ratings for AC Power Supply indicated above. - For DC input power, Idle Power is 38W and Max is 68W. - DC Max input current is 8A. Units are supplied without a power supply. Customer must buy 1 or 2 JD362B (AC) or JD366B (DC) power supply. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; IEC 62368-1; CAN/CSA-C22.2 No. 60950-1; EN 62368-1/A11; FDA 21 CFR Subchapter J; ROHS Compliance Emissions FCC Part 15 Subpart B CLASS A; ICES-003 CLASS A; VCCI-CISPR 32 CLASS A; EN 55032 CLASS; AS/NZS CISPR32 CLASS A; CISPR 24; EN 55024; EN 61000-3-2; EN 61000-3-3; ETSI EN 300 386; GB/T 9254; YD/T 993 Immunity Generic EN 55024 ESD EN300 386 Management IMC - Intelligent Management Center; SmartMC;command-line interface; Web browser; SNMP Manager Ports (16) SFP 100/1000 Mbps ports (8) SFP dual-personality ports - 10/100/1000BASE-T RJ-45 or 100/1000BASE-X Combo Ports (4) SFP+ fixed 1000/10000 SFP+ ports Throughput up to 96 Mpps Routing/switching capacity 128 Gbps PoE capability 370W PoE+ Maximum, depending on model Stacking capabilities IRF 9 switches Management features IMC - Intelligent Management CenterSmartMCCommand-line interfaceWeb browserSNMP manager Input voltage 100 - 240 VAC, rated -48 to -60 VDC, rated (depending on power supply chosen) Power consumption 57 W (maximum) Product dimensions (imperial) 1.72 x 17.32 x 14.17 in Weight 13.23 lbs UNSPSC code 43222612

Podívejte se také Tenda TEG1050F Gigabit Switch with SFP (TEG1050F)

I/O ports and slots 16 SFP 100/1000 Mbps ports8 SFP dual-personality ports; 100/1000BaseX or 100/1000BASET RJ-45 Combo Ports4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Power supplies 2 power supply slots1 minimum power supply required (ordered separately) Physical characteristics Dimensions17.32(w) x 14.17(d) x 1.72(h) in (44 x 36 x 4.36 cm) (1U height)Weight17.64 lb (8 kg) Memory and processor 1 GB SDRAM, 128 MB flash; packet buffer size: 1.5 MB Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance 1000 Mb Latency < 5 µs10 Gbps Latency < 1.5 µsThroughput 96 MppsRouting/Switching capacity 128 GbpsRouting table size 512 entries (IPv4), 256 entries (IPv6)MAC address table size 16384 entries Reliability MTBF (years) 52.79 Environment Operating temperature 32°F to 113°F (0°C to 45°C)Operating relative humidity 10% to 90%, noncondensingNonoperating/Storage temperature -40°F to 158°F (-40°C to 70°C)Nonoperating/Storage relative humidity 5% to 95%, noncondensingAcoustic Low-speed fan: 47.1 dB, High-speed fan: 50.7 dB; ISO 7779 Electrical characteristics Frequency 50/60 HzMaximum heat dissipation 102/204 BTU/hr (107.61/215.22 kJ/hr), for AC Powered units. For DC powered units heat dissipation is 130BTU/hr min, 232BTU/hr max.AC voltage 100 - 240 VACDC voltage -48 to -60 VDCCurrent 5 AMaximum power rating 60 WIdle power 30 W Notes Idle power is the actual power consumption of the device with no ports connected.Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.Power Ratings for AC Power Suppply indicated above.For DC input power, Idle Power is 38W and Max is 68W.DC Max input current is 8A. Units are supplied without a power supply. Customer must buy 1 or 2 JD362A(AC) or JD366A (DC) power supply. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance Emissions EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A Immunity Generic EN 55024ESD EN300 386 Management IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager Services Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

Podívejte se také Tenda TEG1024F Gigabit Fanless Rackmount Switch + SFP (TEG1024F)

Aruba 6000 24G Class4 PoE 4SFP 370W Switch RENEW R8N87A EAN: 726316 Specifikace Porty: 24x 10/100/1000BASE-T Ports SFP porty: 4x 1G/10G PoE: Podporuje IEEE 802.3af, 802.3at USB porty: 1x USB-C Console Port, 1x USB Type-A Host port Zdroj energie a fyzické vlastnosti Zdroj energie: Pevný, až 370W třídy 4 PoE Ventilátory: Pevné Rozměry: 4.39 cm (V) x 44.2 cm (Š) x 26.82 cm (H) Hmotnost: 4.19 kg Technické parametry Procesor: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť: 4 GB DDR3, 16 GB eMMC Packet Buffer: 12.38MB Kapacita přepínání: 56 Gbps Průchodová kapacita: 41.6 Mpps Prostředí Provozní teplota: 0°C do 45°C Relativní vlhkost při provozu: 15% až 95% při 40°C Maximální provozní výška: 3000 metrů Elektrické vlastnosti Frekvence: 50 / 60 Hz AC napětí: 100-127 VAC / 200-240 VAC Proud: 4.6 A / 2.3 A Bezpečnost a certifikace Bezpečnost: UL 60950-1; IEC 60950-1; EN 60950-1 Emise: VCCI-CISPR 32, Class A Montáž a skříň Montuje se do standardního 19-palcového telco racku nebo skříně pro zařízení (k dispozici montážní sada); montáž na vodorovnou plochu; montáž na stěnu.

Podívejte se také CUDY 16-Port 10/100M PoE+ Switch with 1Gigabit Uplink and 1 Gigabit Combo SFP Port 200W (FS1018PS1 )

• CUDY 4-Port Gigabit Industrial Switch with 2 Gigabit SFP Port (IG1004S2)
• CUDY 24-Port Gigabit PoE+ Switch with 2 SFP ports 300W (GS1028PS2)
• CUDY 8-Port Gigabit Industrial Switch with 2 Gigabit SFP Port (IG1008S2)
• Star Wars Racer and Commando Combo - Nintendo Switch (9120080076908)
• AMS 5140 stolní hodiny
• CUDY 4-Port Gigabit Industrial PoE Switch with 2 Gigabit SFP Port (IG1004S2P)
• Elektrobock PT04-EI (0645)
• HPE MicroServer Gen10+ (P16006-421)
• HPE MicroServer Gen10+ (P18584-421)
• HPE ML30 Gen10+ (P44718-421)
• QNAP TS-410E-8G (TS-410E-8G)
• Salente Combo 4v1 (COMBO-4IN1)
• NAS QNAP TS-364-8G (TS-364-8G)
• NAS QNAP TS-1655-8G (TS-1655-8G)
• NAS QNAP TS-253E-8G (TS-253E-8G)
• NAS QNAP TS-664-8G (TS-664-8G)
• Elektrobock PT712-EI + čidlo podlahy (0616)
• BAGMASTER 8G (8591805010414)
• NAS QNAP TVS-h474-PT-8G (TVS-h474-PT-8G)
• D-Link GO-SW-24G (GO-SW-24G/E)

HPE Networking Comware Switch 48G 4SFP+ EI 5140 The HPE Networking Comware Switch Series 5140 EI comprises Gigabit Ethernet switches that support static, OSPF and RIP Layer 3 routing, convenient fixed 10GbE uplink ports, PoE+, ACLs, IPv6 and delivers energy savings with Energy Efficient Ethernet. Unique Intelligent Resilient Fabric (IRF) technology creates a virtual fabric by managing several switches as one logical device, which increases network resilience, performance, and availability, while reducing operational complexity. These switches provide Gigabit Ethernet access and can be used at the edge of a network or to connect server clusters in small data centers. High availability, simplified management, and comprehensive security control policies are among the key features that distinguish this series. HPE FlexNetwork 5140 48G 4SFP+ EI Switch (JL829A) I/O ports and slots 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions 17.32(w) x 9.04(d) x 1.72(h) in (44 x 23 x 4.36 cm) (1U height) Weight 7.72 lb (3.5 kg) Memory and processor 512 MB SDRAM, 256 MB flash Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (Rack Mount Kit R8M91A sold separately) Performance IPv6 Ready Certified 1000 Mb Latency HPE Aruba Networking > Switches - FlexNetwork: 5140 EI Switch Series Transceivers SFP Transceivers Notes: Enter the following menu selections as integrated to the CTO Model X above if order is factory built. Rule # Description SKU HPE Networking X115 100M SFP LC FX Transceiver JD102B HPE Networking X110 100M SFP LC LX Transceiver JD120B HPE Networking X115 100M SFP LC BX 10-U Transceiver JD100A HPE Networking X115 100M SFP LC BX 10-D Transceiver JD101A HPE Networking X120 1G SFP LC SX Transceiver JD118B HPE Networking X120 1G SFP LC LX Transceiver JD119B HPE Networking X120 1G SFP RJ45 T Transceiver JD089B HPE Networking X120 1G SFP LC BX 10-U Transceiver JD098B HPE Networking X120 1G SFP LC BX 10-D Transceiver JD099B HPE Networking X120 1G SFP LC LH100 Transceiver JD103A SFP+ Transceivers Rule # Description SKU HPE Networking X130 10G SFP+ LC SR Transceiver JD092B HPE Networking X130 10G SFP+ LC LR Transceiver JD094B HPE X130 10G SFP+ LC BiDi 10km-Uplink Transceiver JL737A HPE X130 10G SFP+ LC BiDi 10km-Downlink Transceiver JL738A HPE X130 10G SFP+ LC BiDi 40km-Uplink Transceiver JL739A HPE X130 10G SFP+ LC BiDi 40km-Downlink Transceiver JL740A HPE Networking X240 10G SFP+ SFP+ 0.65m DAC Cable JD095C HPE Networking X240 10G SFP+ SFP+ 1.2m DAC Cable JD096C HPE Networking X240 10G SFP+ SFP+ 3m DAC Cable JD097C HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable JG081C HPE X2A0 10G SFP+ to SFP+ 7m Active Optical Cable JL290A HPE X2A0 10G SFP+ to SFP+ 10m Active Optical Cable JL291A HPE X2A0 10G SFP+ to SFP+ 20m Active Optical Cable JL292A Cables Multi-Mode Cables Rule # Description SKU HPE LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable AJ833A HPE LC to LC Multi-mode OM3 2-Fiber 1.0m 1-Pack Fiber Optic Cable AJ834A HPE LC to LC Multi-mode OM3 2-Fiber 2.0m 1-Pack Fiber Optic Cable AJ835A HPE LC to LC Multi-mode OM3 2-Fiber 5.0m 1-Pack Fiber Optic Cable AJ836A HPE LC to LC Multi-mode OM3 2-Fiber 15.0m 1-Pack Fiber Optic Cable AJ837A HPE LC to LC Multi-mode OM3 2-Fiber 30.0m 1-Pack Fiber Optic Cable AJ838A HPE LC to LC Multi-mode OM3 2-Fiber 50.0m 1-Pack Fiber Optic Cable AJ839A HPE Premier Flex LC/LC Multi-mode OM4 2 Fiber 1m Cable QK732A HPE Premier Flex LC/LC Multi-mode OM4 2 Fiber 2m Cable QK733A HPE Premier Flex LC/LC Multi-mode OM4 2 Fiber 5m Cable QK734A HPE Premier Flex LC/LC Multi-mode OM4 2 Fiber 15m Cable QK735A HPE Premier Flex LC/LC Multi-mode OM4 2 Fiber 30m Cable QK736A HPE Premier Flex LC/LC Multi-mode OM4 2 Fiber 50m Cable QK737A Internal Power Supplies HPE X361 150W DC Power Supply Rule # Description SKU 1, 2 HPE X361 150W 100-240VAC to 12VDC Power Supply JD362B Notes: Includes 1 x c13, 150w HPE X361 150W 100-240VAC to 12VDC Power Supply JD362B Notes: C13 PDU Jumper Cord (NA/MEX/TW/JP) HPE X361 150W 100-240VAC to 12VDC Power Supply JD362B Notes: C13 PDU Jumper Cord (ROW) HPE X361 150W 100-240VAC to 12VDC Power Supply JD362B Notes: HPE 2.3m C13 to NEMA 6-15P Pwr Cord(J9936A) HPE X361 150W 100-240VAC to 12VDC Power Supply JD362B Notes: No Localized Power Cord Selected Configuration Rules Rule # Description 1 If #B2E is selected Then replace Localized option with #B2E for power supply and with #B2E for switch . (Offered only in North America, Mexico, Taiwan, and Japan) 2 Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) . (See Localization Menu)REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the Defaulted Power Cable option on the Switches/Routers. Notes: - Drop down under power supply should offer the following options and results: o Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW. (OCA Default B2B or B2C for Rack Level CTO) o Switch/Router/Power Supply to Wall Power Cord - Localized Option (OCA Default for BTO) o High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North America, Mexico, Taiwan, and Japan) o No Localized Power Cord Selected - #AC3 Option Switch Enclosure Options Rack Mount Kits Rule # Description SKU HPE 5140 Rack Mount Kit R8M91A External/Redundant Power Supplies Rule # Description SKU 2, 3, 5, 6 HPE Networking RPS 800 Redundant Power Supply JD183A Notes: Height = 1U includes 1 x c13, 800w 2, 3, 5 HPE RPS1600 Redundant Power System JG136A Notes: Height = 1U includes 1 x c13, 1600w and Power Supply port 1, 5 HPE RPS1600 1600W AC Power Supply JG137A Notes: Installs into JG136A only Configuration Rules Rule # Description 1 If this power supply is selected, The JG136A - HP A-RPS1600 Redundant Power System must be on order or onsite. 2 Localization required. (See Localization Menu for list.) 3 Only 1 JD183A or JG136A can be connected per switch. 5 Supported on JL827A and JL824A 6 Supported on JL826A only when connected to DC Power Supply JD366B with cable JD186A. External/Redundant Power Cables Rule # Description SKU 1 HPE X290 500 V 1m RPS Cable JD186A 2 HPE X290 1000 A JD5 2m RPS Cable JD187A 3 HPE X290 1000 A JD5 NonPoE 2m RPS Cable JD188A Configuration Rules Rule # Description 1 Supported on JL826A with JD366B to connect to JD183A. 2 Supported on JL829A, JL827A, JL823A, JL825A to connect to JG136A. 3 Supported on JG829A and JL826A to connect to JG136A.

Objev podobné jako HPE Networking Comware Switch 48G 4SFP+ EI 5140 JL829AR RENEW

Aruba 6000 48G 4SFP Switch R8N86AR RENEW EAN: 726354 Zvyšte výkon sítě s Aruba 6000 48G 4SFP Switch. Tento přepínač je ideální pro náročné sítě. Specifikace portů Přepínač Aruba 6000 48G 4SFP je vybaven 48x porty 10/100/1000BASE-T a 4x 1G/1G SFP porty. Dále obsahuje 1x USB-C Console Port a 1x USB Type-A Host port pro snadné připojení a správu. Dimenze a hmotnost Aruba 6000 48G 4SFP má rozměry 4.39 cm x 44.2 cm x 24.74 cm a váží 3.42 kg. Je kompaktní a lehký pro snadnou instalaci a přenos. Výkon a kapacita Přepínač má dvojjádrový procesor ARM Cortex A9 s frekvencí 1016 Mhz, 4 GB DDR3 paměť a 16 GB eMMC flash paměť. Jeho přepínací kapacita je 104 Gbps a propustnost 77.3 Mpps. Bezpečnost a regulace Aruba 6000 48G 4SFP splňuje bezpečnostní standardy UL 60950-1, IEC 60950-1, EN 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60825-1, UL 62368-1 Ed. 2, IEC 62368-1 Ed. 2, EN 62368-1:2014. Provozní podmínky Aruba 6000 48G 4SFP může pracovat v teplotách od 0°C do 45°C a relativní vlhkosti od 15% do 95% při teplotě 40°C. Elektrické charakteristiky Přepínač pracuje na frekvenci 50/60 Hz, napětí 100-127 VAC / 200-240 VAC a proud 0.8 A / 0.5 A. Spotřeba energie v klidu je 20.6W a maximální spotřeba (bez PoE) je 44.2W. Klíčové vlastnosti 48x porty 10/100/1000BASE-T 4x 1G/1G SFP porty USB-C Console Port a USB Type-A Host port Dvojjádrový procesor ARM Cortex A9 s frekvencí 1016 Mhz 4 GB DDR3 paměť a 16 GB eMMC flash paměť Přepínací kapacita 104 Gbps a propustnost 77.3 Mpps Dodáváme s pevnými napájecími zdroji a pevnými ventilátory pro bezproblémový provoz. Aruba 6000 48G 4SFP je ideální pro náročné sítě vyžadující vysoký výkon a spolehlivost.

Objev podobné jako HPE Aruba Networking CX 6000 48G 4SFP Switch R8N86AR RENEW

Aruba Instant On 1930 24G 4SFP/SFP+ Switch EAN: 190017355450 Aruba Instant On 1930 24G 4SFP/SFP+ Switch je výkonný switch navržený pro malé podniky. Fyzické vlastnosti Switch má rozměry 17.42(w) x 8.72(d) x 1.73(h) palce a váží 2.41 kg. Výkon S ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM a 256 MB flash dosahuje propustnost 95.23 Mpps a kapacitu 128 Gbps. Spolehlivost MTBF je 158 let. Prostředí Pracuje v teplotách od 0°C do 40°C a vlhkosti 15% až 95% při 40°C. Elektrické vlastnosti Frekvence: 50-60 Hz, napětí: 100-240V, proud: 0.5/0.3 A, maximální výkon: 22.6 W, klidový výkon: 9.3 W. Bezpečnost Switch je certifikovaný dle standardů UL 60950-1, IEC 60950-1,EN 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60825-1 a dalších. Správa zařízení Aruba Instant On Cloud; Web browser; SNMP Manager Montáž Montuje se do standardu EIA 19 in. telco rack nebo do skříně. Podporuje také stolní, stěnovou a podstolní montáž. Klíčové vlastnosti Chytrý spravovaný switch s vrstvou 2+ PoE pro napájení AP a IoT zařízení Bezpečnostní ovládání pro definování přístupu v síti Pohodlná mobilní aplikace a webové rozhraní pro nastavení a správu Standardní funkce Plug-and-play switchy, které fungují s AP Instant On hned po vybalení Mobilní aplikace pro snadné nastavení, sledování a správu sítě Automatická ochrana před DoS útoky Bez dodatečných licenčních nebo předplatných poplatků Průmyslově nejlepší omezená doživotní záruka a podpora Management Cloudové řízení celé sítě, jednoduché lokální webové GUI řízení, podpora až pěti (5) HTTP a HTTP Secure (HTTPS) relací. Kvalita služby (QoS) Prioritizace provozu, IEEE 802.1p/Q VLAN značení, třída služby (CoS), pokročilý klasifikátor na základě QoS. Bezpečnost sítě TPM-based security, IEEE 802.1Q VLAN support, IEEE 802.1X access control, automatická ochrana před DoS útoky, ochrana před bouří paketů, RADIUS, RADIUS účetnictví, Management VLAN ID, prevence proti Link Flap. Výkon a efektivita Energy Efficient Ethernet (EEE), automatické vypnutí portu, stav úspory energie, energeticky účinné chlazení, bezventilátorový provoz. Switchingové funkce IEEE 802.3x Flow control, Spanning Tree Protocol (STP), ochrana proti smyčkám, BPDU filtrování, podpora Jumbo frame, IGMP snooping v1/v2, Link agregace, LLDP/LLDP-MED (Media Endpoint Discovery), Address Resolution Protocol (ARP). Záruka, servis a podpora Aruba Instant On Limited Lifetime Support poskytuje 24X7 telefonickou podporu po prvních 90 dnech a chatovou podporu po celou dobu záruky. Komunitní podpora je zahrnuta po dobu života produktu.

Objev podobné jako HPE Networking Instant On Switch 24p Gigabit 4p SFP+ 1930 (JL682A)

Aruba 6000 48G Class4 PoE 4SFP 370W Switch EAN: 190017559742 Popis produktu Aruba 6000 48G 4SFP Switch je vybaven 48x porty 10/100/1000BASE-T a 4x 1G/10G SFP porty. Vlastnosti CPU: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť a Flash: 4 GB DDR3 16 GB eMMC Packet Buffer: 12.38MB (4.5MB Ingress/7.875MB Egress) Výkon Aruba 6000 48G 4SFP Switch nabízí přepínací kapacitu 104 Gbps a propustnost 77.3 Mpps. Prostředí Při provozní teplotě 32°F to 113°F (0°C to 45°C) lze tento switch použít až do výšky 5000 ft (1.5 km). Elektrické charakteristiky Frekvence: 50 / 60 Hz AC Napětí: 100-127 VAC / 200-240 VAC Spotřeba energie (230 VAC): Idle: 30.6W Max Power (w/o PoE): 45W Max Power (w/ PoE): 480W Bezpečnost Aruba 6000 48G 4SFP Switch je certifikován dle UL 60950-1; IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014. Montáž a skříň Aruba 6000 48G 4SFP Switch lze namontovat do standardního 19-palcového telco racku nebo do skříně pro zařízení.

Objev podobné jako HPE Aruba Networking CX 6000 48G Class4 PoE 4SFP 370W Switch

HPE FlexNetwork 5140 24G PoE+ 4SFP+ EI Switch JL827A RENEWThe HPE FlexNetwork 5140 EI Switch Series comprises Gigabit Ethernet switches that support static, OSPF and RIP Layer 3 routing, convenient fixed 10GbE uplink ports, PoE+, ACLs, IPv6 and delivers energy savings with Energy Efficient Ethernet. Unique Intelligent Resilient Fabric (IRF) technology creates a virtual fabric by managing several switches as one logical device, which increases network resilience, performance, and availability, while reducing operational complexity. These switches provide Gigabit Ethernet access and can be used at the edge of a network or to connect server clusters in small data centers. High availability, simplified management, and comprehensive security control policies are among the key features that distinguish this series. HPE FlexNetwork 5140 48G 4SFP+ EI Switch (JL829A) I/O ports and slots 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions 17.32(w) x 9.04(d) x 1.72(h) in (44 x 23 x 4.36 cm) (1U height) Weight 7.72 lb (3.5 kg) Memory and processor 512 MB SDRAM, 256 MB flash Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (Rack Mount Kit R8M91A sold separately) Performance IPv6 Ready Certified 1000 Mb Latency < 5 µs 10 Gbps Latency < 3 µs Throughput 131 Mpps Routing/Switching capacity 176 Gbps Routing table size 1024 entries MAC address table size 16384 entries Environment Operating temperature 23°F to 113°F (-5°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Non-operating/Storage temperature -40°F to 158°F (-40°C to 70°C) Non-operating/Storage relative humidity 5% to 95%, noncondensing Acoustic Low-speed fan: 42.2 dB, High-speed fan: 49.3 dB; ISO 7779 Electrical characteristics Frequency 50/60 Hz Maximum heat dissipation 130/153 BTU/hr (137.15/161.42 kJ/hr), For AC powered units. For DC powered units heat dissipation is 130 BTU/hr min, 171 BTU/hr max Voltage 100 - 240 VAC -48 to -60 VDC Current 10 A Maximum power rating 44 W Idle power 38 W Notes: - Idle power is the actual power consumption of the device with no ports connected. - Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. - Power ratings for AC power indicated above. Current used is 5A Max when DC Power used. For DC input power, idle power is 38W, maximum DC power used is 50W. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; IEC 62368-1; CAN/CSA-C22.2 No. 60950-1; EN 62368-1/A11; FDA 21 CFR Subchapter J; ROHS Compliance Emissions FCC Part 15 Subpart B CLASS A; ICES-003 CLASS A; VCCI-CISPR 32 CLASS A; EN 55032 CLASS; AS/NZS CISPR32 CLASS A; CISPR 24; EN 55024; EN 61000-3-2; EN 61000-3-3; ETSI EN 300 386; GB/T 9254; YD/T 993 Immunity Generic EN 55024 ESD EN300 386 Management IMC - Intelligent Management Center; SmartMC; command-line interface; Web browser; SNMP Manager Services Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. HPE FlexNetwork 5140 24G PoE+ 4SFP+ (370W) EI Switch (JL827A ) I/O ports and slots 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T) with 4 combo ports (RJ-45 or SFP); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions 17.32(w) x 10.24(d) x 1.72(h) in (44 x 26 x 4.36 cm) (1U height) Weight 17.64 lb (8 kg) Memory and processor 512 MB SDRAM, 256 MB flash Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (Rack Mount Kit R8M91A sold separately) Performance IPv6 Ready Certified 1000 Mb Latency < 5 µs 10 Gbps Latency < 3 µs Throughput 95 Mpps Routing/Switching capacity 128 Gbps Routing table size 1024 entries MAC address table size 16384 entries Environment Operating temperature 23°F to 113°F (-5°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Non-operating/Storage temperature -40°F to 158°F (-40°C to 70°C) Non-operating/Storage relative humidity 5% to 95%, noncondensing Acoustic Low-speed fan: 44.4 dB, High-speed fan: 53.6 dB; ISO 7779 Electrical characteristics Frequency 50/60 Hz Maximum heat dissipation 102/1569 BTU/hr (107.61/1655.29 kJ/hr), for AC Power. For DC Power min heat dissipation is 85 BTU/hr and max heat dissipation is 2695 BTU/hr Voltage 100 - 240 VAC, -54 to -57 VDC Current 10 A Maximum power rating 451 W Idle power 30 W PoE power 370 W PoE+ Notes: - Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. PoE Power is the power supplied by the internal power supply. When supplemented with the use of an HPE RPS1600 Redundant Power System, up to 740 W of PoE+ can be supplied. - Max current rating for DC power is 25A. AC Input power is 30W typical, and 460W max(including 370W PoE+ consumption. DC Input voltage range is -54 to -57VDC. Total DC input power is 25W Typical and 790W with 740W PoE+ Power consumption. DC Input voltage range is -54VDC to -57VDC. DC Input Source is the HPE RPS1600. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; IEC 62368-1; CAN/CSA-C22.2 No. 60950-1; EN 62368-1/A11; FDA 21 CFR Subchapter J; ROHS Compliance Emissions FCC Part 15 Subpart CLASS A; ICES-003 CLASS A; VCCI-CISPR 32 CLASS A; EN 55032 CLASS; AS/NZS CISPR32 CLASS A; CISPR 24; EN 55024; EN 61000-3-2; EN 61000-3-3; ETSI EN 300 386; GB/T 9254; YD/T 993 Immunity Generic EN 55024 ESD EN300 386 Management IMC - Intelligent Management Center; SmartMC; command-line interface; Web browser; SNMP Manager. Services Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. Models HPE FlexNetwork 5140 24G POE+2SFP+2XGT EI Switch JL823A HPE FlexNetwork 5140 48G PoE+ 4SFP+ EI Switch JL824A HPE FlexNetwork 5140 48G POE+ 2SFP+ 2XGT EI Switch JL825A HPE FlexNetwork 5140 24G SFP w/8G Combo 4SFP+ EI Switch JL826A HPE FlexNetwork 5140 24G PoE+ 4SFP+ EI Switch JL827A HPE FlexNetwork 5140 24G 4SFP+ EI Switch JL828A HPE FlexNetwork 5140 48G 4SFP+ EI Switch JL829A HPE FlexNetwork 5140 24G 2SFP+ 2XGT EI Switch R8J41A HPE FlexNetwork 5140 8G 2SFP 2GT Combo EI Switch R8J42A Key features Gigabit Ethernet access switch with static layer 3 routing, RIP, high density 10GbE uplinks and POE+ models for voice, video and wireless IRF technology that enables plug-and-play device aggregation and link aggregation across multiple devices Embedded network management capabilities at no additional cost with Smart Management Centre (SmartMC) Energy-saving green design features such as automatic switching of idle ports to energy-saving mode and powering down unused ports Standard Features Software-defined networking OpenFlow Supports OpenFlow 1.3 specification to enable SDN by allowing separation of the data (packet forwarding) and control (routing decision) paths Quality of Service (QoS) Broadcast control Allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic Advanced classifier-based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority level and rate limit to selected traffic on a port, VLAN, or whole switch Powerful QoS feature Supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR), and SP+WRR Traffic policing Supports Committed Access Rate (CAR) and line rate Connectivity Auto-MDIX Automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports Flow control Provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations High-density connectivity Provides up to 48 fixed 10/100/1000BASE-T ports in a Layer 2/Layer 3 switch IEEE 802.3at Power over Ethernet (PoE+) support Simplifies deployment and dramatically reduces installation costs by helping to eliminate the time and cost involved in supplying local power at each access point location Ethernet operations, administration and maintenance (OAM) Detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the status of the link between two devices Resiliency and high availability Separate data and control paths Separate control from services and keeps service processing isolated; increases security and performance External redundant power supply Provides high reliability Smart link Allows 100 ms failover between links Spanning Tree/MSTP, RSTP, PVST+, RPVST+ Link redundancy with support for protocols such as Multiple Spanning Tree Protocol (MSTP), Rapid Spanning Tree Protocol (RSTP), Per-VLAN Spanning Tree (PVST+), Rapid Per-VLAN Spanning Tree (RPVST+), Equal-Cost Multipath (ECMP), and Smart Link provides high availability Intelligent Resilient Fabric (IRF) Creates virtual resilient switching fabrics, where two or more switches perform as a single L2 switch and L3 router; switches do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached using standard LACP for automatic load balancing and high availability; can eliminate the need for complex protocols like Spanning Tree Protocol, (), or VRRP, thereby simplifying network operation Layer 3 routing Static IP routing Provides manually configured routing for both IPv4 and IPv6 networks Open Shortest Path First (OSPF) An Interior Gateway Protocol (IGP) that uses a link state routing algorithm; supports OSPFv1/v2 and OSPFv3 Routing Information Protocol (RIP) Uses a distance vector algorithm with UDP packets for route determination; supports RIPv1 and RIPv2 routing; includes loop protection Management Remote configuration and management Enables configuration and management through a secure Web browser or a CLI located on a remote device Manager and operator privilege levels Provides read-only (operator) and read/write (manager) access on CLI and Web browser management interfaces Command authorization Leverages HWTACACS to link a custom list of CLI commands to an individual network administrator's login; also provides an audit trail Secure Web GUI Provides a secure, easy-to-use graphical interface for configuring the module via HTTPS Multiple configuration files Stores easily to the flash image Complete session logging Provides detailed information for problem identification and resolution Remote monitoring (RMON) Uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a private alarm extension group IEEE 802.1AB Link Layer Discovery Protocol (LLDP) Advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network management applications sFlow (RFC 3176) Provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and real-time network monitoring purposes Management VLAN Segments traffic to and from management interfaces, includingCLI/telnet, a Web browser interface, and SNMP Remote intelligent mirroring Mirrors ingress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the network Device Link Detection Protocol (DLDP) Monitors a cable between two compatible switches and shuts down the ports on both ends if the cable is broken, which prevents network problems such as loops IPv6 management Provides future-proof networking because the switch is capable of being managed whether the attached network is running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, syslogv6, FTPv6, SNMPv6, DHCPv6, and RADIUS for IPv6 Troubleshooting Ingress and egress port monitoring enables network problem-solving; virtual cable tests provide visibility into cable problems Smart Management Center (SmartMC) Embedded network management tool with a web-based GUI to simplify operations and facilitate centralized management. It is made available at no additional cost and offers centralized configuration backup, software version management and seamless switch replacement. HPE Intelligent Management Center (IMC) Integrates fault management, element configuration, and network monitoring from a central vantage point; built-in support for third-party devices enables network administrators to centrally manage all network elements with a variety of automated tasks, including discovery, categorization, baseline configurations, and software images; the software also provides configuration comparison tools, version tracking, change alerts, and more Network Management SNMP v1/v2c/v3, MIB-II with Traps, and RADIUS Authentication Client MIB (RFC 2618); embedded HTML management tool with secure access Security Access control lists (ACLs) Provides IP Layer 2 to Layer 4 traffic filtering; supports global ACL, VLAN ACL, port ACL, and IPv6 ACL IEEE 802.1X Industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server MAC-based authentication Client is authenticated with the RADIUS server based on the client's MAC address Identity-driven security and access control - Per-user ACLs Permits or denies user access to specific network resources based on user identity and time of day, allowing multiple types of users on the same network to access specific network services without risking network security or providing unauthorized access to sensitive data - Automatic VLAN assignment Automatically assigns users to the appropriate VLAN based on their identities Secure management access Delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, HTTPS and/or SNMPv3 Secure FTP/ SCP Allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch configuration file Guest VLAN Provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X Port security Allows access only to specified MAC addresses, which can be learned or specified by the administrator Port isolation Secures and adds privacy, and prevents malicious attackers from obtaining user information STP BPDU port protection Blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks STP root guard Protects the root bridge from malicious attacks or configuration mistakes DHCP protection Blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks IP source guard Helps prevent IP spoofing attacks Dynamic ARP protection Blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data RADIUS/HWTACACS Eases switch management security administration by using a password authentication server Performance Nonblocking architecture Up to 176 Gb/s nonblocking switching fabric provides wirespeed switching with up to 130.9 Mpps throughput Hardware-based wirespeed access control lists (ACLs) Help provide high levels of security and ease of administration without impacting network performance with a feature-rich TCAM-based ACL implementation Device support Prestandard PoE Support Detects and provides power to prestandard PoE devices such as wireless LAN access points and IP phones Convergence IEEE 802.1AB Link Layer Discovery Protocol (LLDP) Facilitates easy mapping using network management applications with LLDP automated device discovery protocol LLDP-MED Is a standard extension that automatically configures network devices, including LLDP-capable IP phones LLDP-CDP compatibility Receives and recognizes CDP packets from Cisco's IP phones for seamless interoperation IEEE 802.3at Power over Ethernet (PoE+) Provides up to 30 W per port that allows support of the latest PoE+-capable devices such as IP phones, wireless access points, and security cameras, as well as any IEEE 802.3af-compliant end device; eliminates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments PoE allocations Supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to allocate PoE power for more efficient energy savings Voice VLAN Automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance IP multicast snooping (data-driven IGMP) Prevents flooding of IP multicast traffic Additional information Green IT and power Improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and utilizes variable-speed fans, reducing energy costs Green initiative support Provides support for RoHS and WEEE regulations Unified Hewlett Packard Enterprise Comware operating system with modular architecture Provides an easy-to-enhance-and-extend feature set, which doesn't require whole-scale changes; all switching, routing, and security platforms leverage the Comware OS, a common unified modular operating system Energy Efficient Ethernet (EEE) Support Reduces power consumption in accordance with IEEE 802.3az Layer 2 switching 16K MAC address table Provides access to many Layer 2 devices VLAN support and tagging Supports IEEE 802.1Q with 4,094 simultaneous VLAN IDs IEEE 802.1ad QinQ and selective QinQ Increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a high-speed campus or metro network 10GbE port aggregation Allows grouping of ports to increase overall data throughput to a remote device Device Link Detection Protocol (DLDP) Monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STP-based networks Jumbo Frame Support Improves the performance of large data transfers; supports frame size of up to 9K-bytes Layer 3 services Address Resolution Protocol (ARP) Determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a Layer 2 network Dynamic Host Configuration Protocol (DHCP) Simplifies the management of large IP networks; supports client; DHCP Relay enables DHCP operation across subnets Loopback interface address Defines an address that can always be reachable, improving diagnostic capability User Datagram Protocol (UDP) helper function Allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents server spoofing for UDP services such as DHCP Route maps Provide more control during route redistribution; allow filtering and altering of route metrics DHCP server Centralizes and reduces the cost of IPv4 address management Warranty and support Limited Lifetime Warranty See Warranty check for warranty and support information included with your product purchase. Software releases To find software for your product, refer to http://www.hpe.com/networking/support; for details on the software releases available with your product purchase, refer to Warranty check

Objev podobné jako HPE FlexNetwork 5140 24G PoE+ 4SFP+ EI Switch JL827A RENEW

I/O ports and slots 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions17.32(w) x 6.3(d) x 1.72(h) in (44 x 16 x 4.36 cm) (1U height)Weight11.02 lb (5 kg) Memory and processor 1 GB SDRAM, 128 MB flash; packet buffer size: 1.5 MB Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance 1000 Mb Latency< 5 µs10 Gbps Latency< 1.5 µsThroughput 96 MppsRouting/Switching capacity 128 GbpsRouting table size 512 entries (IPv4), 256 entries (IPv6)MAC address table size 16384 entries Reliability MTBF (years) 98.1 Environment Operating temperature 32°F to 113°F (0°C to 45°C)Operating relative humidity 10% to 90%, noncondensingNonoperating/Storage temperature -40°F to 158°F (-40°C to 70°C)Nonoperating/Storage relative humidity 5% to 95%, noncondensingAcoustic High-speed fan: 39.7 dB; ISO 7779 Electrical characteristics Frequency 50/60 HzMaximum heat dissipation 64/88 BTU/hr (67.52/92.84 kJ/hr)AC voltage 100-240 VACCurrent 2 AMaximum power rating 26 WIdle power 19 W Notes Idle power is the actual power consumption of the device with no ports connected.Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance Emissions EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A Immunity Generic EN 55024ESD EN300 386 Management IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager Services Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office. HPE FlexNetwork 5130 24G 4SFP+ EI Switch (JG932A) I/O ports and slots 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions 17.32(w) x 6.3(d) x 1.72(h) in (44 x 16 x 4.36 cm) (1U height) Weight 11.02 lb (5 kg) Memory and processor 1 GB SDRAM, 512 MB flash; packet buffer size: 1.5 MB Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance IPv6 Ready Certified 1000 Mb Latency < 5 µs 10 Gbps Latency < 3 µs Throughput 96 Mpps Routing/Switching capacity 128 Gbps Routing table size 512 entries (IPv4), 256 entries (IPv6) MAC address table size 16384 entries Environment Operating temperature 23°F to 113°F (-5°C to 45°C) Operating relative humidity 10% to 90%, noncondensing Non-operating/Storage temperature -40°F to 158°F (-40°C to 70°C) Non-operating/Storage relative humidity 5% to 95%, noncondensing Acoustic High-speed fan: 39.7 dB; ISO 7779 Electrical characteristics Frequency 50/60 Hz Maximum heat dissipation 64/88 BTU/hr (67.52/92.84 kJ/hr) Voltage 100 - 240 VAC, rated Current 2 A Maximum power rating 26 W Idle power 19 W Notes - Idle power is the actual power consumption of the device with no ports connected. - Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. Safety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance Emissions EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A Immunity Generic EN 55024 ESD EN300 386 Management IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager Services Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Objev podobné jako HPE FlexNetwork 5130 24G 4SFP+ EI Switch HP RENEW JG932A

HPE Aruba Networking CX 6000 24G 4SFP Switch R8N88A RENEW Model Aruba 6000 24G 4SFP Switch (R8N88A) Description 24x ports 10/100/1000BASE-T Ports 4x 1G SFP ports 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply Fans Fixed fans Dimensions (H) 4.39 cm (W) 44.2 cm (D) 20.12 cm (1.73" x 17.4" x 7.92") Configuration Weight 2.62 kg (5.78 lbs) CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Model Switching Capacity 56 Gbps Model Throughput Capacity 41.6 Mpps Average Latency (LIFO-64-bytes packets) 1 Gbps: 1.5 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.9 Bel Sound Pressure, LpAm (Bystander) = 20.9 dB Primary Airflow Side-to-side Aruba 6000 24G 4SFP Switch (R8N88A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting

Objev podobné jako HPE Aruba Networking CX 6000 24G 4SFP Switch R8N88A RENEW

HPE Aruba Networking CX 6100 24G 4SFP+ Switch JL678A RENEW Aruba 6100 24G 4SFP+ Switch (JL678A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting Standards And Protocols (Applies to all products in series) RFC 1591 DNS (client) SSHv1/SSHv2 Secure Shell IEEE 802.1D MAC Bridges IEEE 802.1p Priority IEEE 802.1Q VLANs IEEE 802.1s Multiple Spanning Trees IEEE 802.1w Rapid Reconfiguration of Spanning Tree IEEE 802.3 Type 10BASE-T IEEE 802.3ab 1000BASE-T IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.3at Power over Ethernet IEEE 802.3az Energy Efficient Ethernet IEEE 802.3x Flow Control RFC 768 UDP RFC 783 TFTP Protocol (revision 2) RFC 792 ICMP RFC 793 TCP RFC 826 ARP RFC 1350 TFTP Protocol (revision 2) RFC 2131 DHCP client RFC 4330 Simple Network Time Protocol (SNTP) v4 RFC 951 BOOTP (VLAN 1 Only) RFC 1542 BOOTP Extensions (VLAN 1 only) IGMPv2/IGMPv3 IGMP/MLD Snooping RFC 1981 IPv6 Path MTU Discovery RFC 2460 IPv6 Specification RFC 2925 Remote Operations MIB (Ping only) RFC 3315 DHCPv6 (client only) RFC 3513 IPv6 Addressing Architecture RFC 3596 DNS Extension for IPv6 RFC 3176 sFlow RFC 4022 MIB for TCP RFC 4113 MIB for UDP (Partially) RFC 4251 SSHv6 Architecture RFC 4252 SSHv6 Authentication RFC 4253 SSHv6 Transport Layer RFC 4254 SSHv6 Connection RFC 4293 MIB for IP RFC 4419 Key Exchange for SSH RFC 4443 ICMPv6 RFC 4861 IPv6 Neighbor Discovery RFC 4862 IPv6 Stateless Address Auto-configuration RFC 1213 MIB RFC 1493 Bridge MIB RFC 2674 802.1p and IEEE 802.1Q Bridge MIB (Partial support. MIB objects supported: ieee8021BridgeBasePort, ieee8021BridgeBasePort, ieee8021BridgePortMrpJoinTime, ieee8021BridgePortMrpLeaveTime, ieee8021BridgePortMrpLeaveAllTime) RFC 2737 Entity MIB RFC 2863 The Interfaces Group MIB IEEE 802.1AB Link Layer Discovery Protocol (LLDP) RFC 1098 A Simple Network Management Protocol (SNMP) ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED) SNMPv1/v2c/v3 RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events) RFC 1098 A Simple Network Management Protocol (SNMP) RFC 2474 DiffServ precedence, with 2/4/8 queues per port RFC 2475 DiffServ Architecture RFC 2597 DiffServ Assured Forwarding (AF) RFC 2598 DiffServ Expedited Forwarding (EF) IEEE 802.1X Port Based Network Access Control RFC 1492 TACACS+ RFC 2138 RADIUS Authentication RFC 2866 RADIUS Accounting Secure Sockets Layer (SSL)

Objev podobné jako HPE Aruba Networking CX 6100 24G 4SFP+ Switch JL678A RENEW

HP 5130-48G-4SFP+ EI Switch HP RENEW 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ fixed 1000/10000 SFP+ ports

Objev podobné jako HPE 5130-48G-4SFP+ EI HP RENEW Switch JG934AR

Cisco switch CBS350-24XT-EU - REFRESH CISCO REFRESH jsou repasované produkty, které společnost CISCO dodává s certifikací kvality, zárukou a servisní podporou odpovídající ekvivalentnímu novému produktu Řízené switche řady Cisco Business 350 jsou spolehlivými stavebními prvky pro sítě malých firem. Díky intuitivnímu ovládacímu panelu, pokročilým funkcím a všudypřítomnému zabezpečení urychlují spravované switche řady Cisco Business 350 vaši digitální transformaci. Záruka platná do End of Support 31. 10. 2029. Oznámení End of Life pro CISCO CBS350 Stránky produktu: CBS350-24XT-EU Quick start guide: Quick start guide Switching capacity and forwarding rate (All switches are wire speed and nonblocking)Capacity in Millions of Packets per Second (mpps) (64-byte packets) 240 Switching Capacity in Gigabits per Second (Gbps) 480 Layer 2 switchingSpanning Tree Protocol (STP) Standard 802.1d Spanning Tree support Fast convergence using 802.1w (Rapid Spanning Tree [RSTP]), enabled by default Multiple Spanning Tree instances using 802.1s (MSTP); 8 instances are supported Per-VLAN Spanning Tree Plus (PVST+) and Rapid PVST+ (RPVST+); 126 instances are supported Port grouping/link aggregation Support for IEEE 802.3ad Link Aggregation Control Protocol (LACP) Up to 8 groups Up to 8 ports per group with 16 candidate ports for each (dynamic) 802.3ad link aggregation VLAN Support for up to 4,094 VLANs simultaneously Port-based and 802.1Q tag-based VLANs; MAC-based VLAN; protocol-based VLAN; IP subnet-based VLAN Management VLAN Private VLAN with promiscuous, isolated, and community port Private VLAN Edge (PVE), also known as protected ports, with multiple uplinks Guest VLAN, unauthenticated VLAN Dynamic VLAN assignment via RADIUS server along with 802.1x client authentication CPE VLAN Voice VLAN Voice traffic is automatically assigned to a voice-specific VLAN and treated with appropriate levels of QoS. Voice Services Discovery Protocol (VSDP) delivers network wide zero-touch deployment of voice endpoints and call control devices Multicast TV VLAN Multicast TV VLAN allows the single multicast VLAN to be shared in the network while subscribers remain in separate VLANs. This feature is also known as Multicast VLAN Registration (MVR) VLAN Translation Support for VLAN One-to-One Mapping. In VLAN One-to-One Mapping, on an edge interface customer VLANs (C-VLANs) are mapped to service provider VLANs (S-VLANs) and the original C-VLAN tags are replaced by the specified S-VLAN Q-in-Q VLANs transparently cross a service provider network while isolating traffic among customers Selective Q-in-Q Selective Q-in-Q is an enhancement to the basic Q-in-Q feature and provides, per edge interface, multiple mappings of different C-VLANs to separate S-VLANs Selective Q-in-Q also allows configuring of Ethertype (Tag Protocol Identifier [TPID]) of the S-VLAN tag Layer 2 protocol tunneling over Q-in-Q is also supported Generic VLAN Registration Protocol (GVRP)/Generic Attribute Registration Protocol (GARP) Generic VLAN Registration Protocol (GVRP) and Generic Attribute Registration Protocol (GARP) enable automatic propagation and configuration of VLANs in a bridged domain Unidirectional Link Detection (UDLD) UDLD monitors physical connection to detect unidirectional links caused by incorrect wiring or cable/port faults to prevent forwarding loops and black holing of traffic in switched networks Dynamic Host Configuration Protocol (DHCP) Relay at Layer 2 Relay of DHCP traffic to DHCP server in different VLAN; works with DHCP Option 82 Internet Group Management Protocol (IGMP) versions 1, 2, and 3 snooping IGMP limits bandwidth-intensive multicast traffic to only the requesters; supports 2K multicast groups (source-specific multicasting is also supported) IGMP Querier IGMP querier is used to support a Layer 2 multicast domain of snooping switches in the absence of a multicast router IGMP proxy The IGMP proxy provides a mechanism for multicast forwarding based on IGMP membership information without the need for more complicated multicast routing protocols. Head-of-Line (HOL) blocking HOL blocking prevention Loopback Detection Loopback detection provides protection against loops by transmitting loop protocol packets out of ports on which loop protection has been enabled. It operates independently of STP Layer 3IPv4 routing Wirespeed routing of IPv4 packets Up to 990 static routes and up to 128 IP interfaces IPv6 routing Wirespeed routing of IPv6 packets Layer 3 Interface Configuration of Layer 3 interface on physical port, Link Aggregation (LAG), VLAN interface, or loopback interface Classless Interdomain Routing (CIDR) Support for classless interdomain routing RIP v2 Support for Routing Information Protocol version 2 for dynamic routing Policy-Based Routing (PBR) Flexible routing control to direct packets to different next hop based on IPv4 or IPv6 Access Control List (ACL) DHCP Server Switch functions as an IPv4 DHCP server serving IP addresses for multiple DHCP pools/scopes Support for DHCP options DHCP relay at Layer 3 Relay of DHCP traffic across IP domains User Datagram Protocol (UDP) relay Relay of broadcast information across Layer 3 domains for application discovery or relaying of Bootstrap Protocol (BOOTP)/DHCP packets StackingHardware stacking Up to 4 units in a stack. Up to 200 ports managed as a single system with hardware failover High availability Fast stack failover delivers minimal traffic loss. Support link aggregation across multiple units in a stack Plug-and-play stacking configuration/management Active/standby for resilient stack control Autonumbering Hot swap of units in stack Ring and chain stacking options, auto stacking port speed, flexible stacking port options High-speed stack interconnects Cost-effective high-speed 10G fiber interfaces. Securityecure Shell (SSH) Protocol SSH is a secure replacement for Telnet traffic. Secure Copy Protocol (SCP) also uses SSH. SSH v1 and v2 are supported Secure Sockets Layer (SSL) SSL support: Encrypts all HTTPS traffic, allowing highly secure access to the browser-based management GUI in the switch IEEE 802.1X (Authenticator role) 802.1X: Remote Authentication Dial-In User Service (RADIUS) authentication and accounting, MD5 hash; guest VLAN; unauthenticated VLAN, single/multiple host mode and single/multiple sessions Supports time-based 802.1X; dynamic VLAN assignment; MAC authentication IEEE 802.1X supplicant A switch can be configured to act as a supplicant to another switch. This enables extended secure access in areas outside the wiring closet (such as conference rooms) Web-based authentication Web-based authentication provides network admission control through web browser to any host devices and operating systems STP Bridge Protocol Data Unit (BPDU) Guard A security mechanism to protect the network from invalid configurations. A port enabled for BPDU Guard is shut down if a BPDU message is received on that port. This avoids accidental topology loops STP Root Guard This prevents edge devices not in the network administrator’s control from becoming Spanning Tree Protocol root nodes STP loopback guard Provides additional protection against Layer 2 forwarding loops (STP loops) DHCP snooping Filters out DHCP messages with unregistered IP addresses and/or from unexpected or untrusted interfaces. This prevents rogue devices from behaving as DHCP Servers. IP Source Guard (IPSG) When IP Source Guard is enabled at a port, the switch filters out IP packets received from the port if the source IP addresses of the packets have not been statically configured or dynamically learned from DHCP snooping. This prevents IP address spoofing. Dynamic ARP Inspection (DAI) The switch discards ARP packets from a port if there are no static or dynamic IP/MAC bindings or if there is a discrepancy between the source or destination addresses in the ARP packet. This prevents man-in-the-middle attacks. IP/MAC/Port Binding (IPMB) The preceding features (DHCP Snooping, IP Source Guard, and Dynamic ARP Inspection) work together to prevent DOS attacks in the network, thereby increasing network availability Secure Core Technology (SCT) Makes sure that the switch will receive and process management and protocol traffic no matter how much traffic is received Secure Sensitive Data (SSD) A mechanism to manage sensitive data (such as passwords, keys, and so on) securely on the switch, populating this data to other devices, and secure autoconfig. Access to view the sensitive data as plaintext or encrypted is provided according to the user-configured access level and the access method of the user. Trustworthy systems Trustworthy systems provide a highly secure foundation for Cisco products Run-time defenses (Executable Space Protection [X-Space], Address Space Layout Randomization [ASLR], Built-In Object Size Checking [BOSC]) Private VLAN Private VLAN provides security and isolation between switch ports, which helps ensure that users cannot snoop on other users’ traffic; supports multiple uplinks Layer 2 isolation Private VLAN Edge (PVE) PVE (also known as protected ports) provides Layer 2 isolation between devices in the same VLAN, supports multiple uplinks Port security Ability to lock source MAC addresses to ports and limits the number of learned MAC addresses RADIUS/TACACS+ Supports RADIUS and TACACS authentication. Switch functions as a client RADIUS accounting The RADIUS accounting functions allow data to be sent at the start and end of services, indicating the amount of resources (such as time, packets, bytes, and so on) used during the session Storm control Broadcast, multicast, and unknown unicast DoS prevention Denial-of-Service (DOS) attack prevention Multiple user privilege levels in CLI Level 1, 7, and 15 privilege levels ACLs Support for up to 1,024 rules Drop or rate limit based on source and destination MAC, VLAN ID, IPv4 or IPv6 address, IPv6 flow label, protocol, port, Differentiated Services Code Point (DSCP)/IP precedence, Transmission Control Protocol/User Datagram Protocol (TCP/UDP) source and destination ports, 802.1p priority, Ethernet type, Internet Control Message Protocol (ICMP) packets, IGMP packets, TCP flag; ACL can be applied on both ingress and egress sides Time-based ACLs supported Quality of ServicePriority levels 8 hardware queues Scheduling Strict priority and Weighted Round-Robin (WRR) Class of service Port based; 802.1p VLAN priority-based; IPv4/v6 IP precedence/Type of Service (ToS)/DSCP-based; Differentiated Services (DiffServ); classification and remarking ACLs, trusted QoS Queue assignment based on DSCP and class of service (802.1p/CoS) Rate limiting Ingress policer; egress shaping and rate control; per VLAN, per port, and flow based; 2R3C policing Congestion avoidance A TCP congestion avoidance algorithm is required to minimize and prevent global TCP loss synchronization iSCSI traffic optimization A mechanism for giving priority to iSCSI traffic over other types of traffic Standards IEEE 802.3 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX Fast Ethernet, IEEE 802.3ab 1000BASE-T Gigabit Ethernet, IEEE 802.3ad Link Aggregation Control Protocol, IEEE 802.3z Gigabit Ethernet, IEEE 802.3ae 10 Gbit/s Ethernet over fiber for LAN, IEEE 802.3an 10GBase-T 10 Gbit/s Ethernet over copper twisted pair cable, IEEE 802.3x Flow Control, IEEE 802.1D (STP, GARP, and GVRP), IEEE 802.1Q/p VLAN, IEEE 802.1w Rapid STP, IEEE 802.1s Multiple STP, IEEE 802.1X Port Access Authentication, IEEE 802.3af, IEEE 802.3at, IEEE 802.1AB Link Layer Discovery Protocol, IEEE 802.3az Energy Efficient Ethernet, RFC 768, RFC 783, RFC 791, RFC 792, RFC 793, RFC 813, RFC 826, RFC 879, RFC 896, RFC 854, RFC 855, RFC 856, RFC 858, RFC 894, RFC 919, RFC 920, RFC 922, RFC 950, RFC 951, RFC 1042, RFC 1071, RFC 1123, RFC 1141, RFC 1155, RFC 1157, RFC 1213, RFC 1215, RFC 1286, RFC 1350, RFC 1442, RFC 1451, RFC 1493, RFC 1533, RFC 1541, RFC 1542, RFC 1573, RFC 1624, RFC 1643, RFC 1700, RFC 1757, RFC 1867, RFC 1907, RFC 2011, RFC 2012, RFC 2013, RFC 2030, RFC 2131, RFC 2132, RFC 2233, RFC 2576, RFC 2616, RFC 2618, RFC 2665, RFC 2666, RFC 2674, RFC 2737, RFC 2819, RFC 2863, RFC 3164, RFC 3176, RFC 3411, RFC 3412, RFC 3413, RFC 3414, RFC 3415, RFC 3416, RFC 4330 IPv6IPv6 IPv6 host mode; IPv6 over Ethernet; Dual IPv6/IPv4 stack IPv6 neighbor and router discovery (ND); IPv6 stateless address autoconfiguration; Path Maximum Transmission Unit (MTU) discovery Duplicate Address Detection (DAD); ICMP version 6 DHCPv6 stateful client IPv6 over IPv4 network with Intrasite Automatic Tunnel Addressing Protocol (ISATAP) tunnel support USGv6 and IPv6 Gold Logo certified IPv6 QoS Prioritize IPv6 packets in hardware IPv6 ACL Drop or rate limit IPv6 packets in hardware IPv6 First Hop Security RA guard ND inspection DHCPv6 guard Neighbor binding table (snooping and static entries) Neighbor binding integrity check Multicast Listener Discovery (MLD v1/2) snooping Deliver IPv6 multicast packets only to the required receivers MLD proxy The MLD proxy provides a mechanism for multicast forwarding based on MLD membership information without the need for more complicated multicast routing protocols. IPv6 applications Web/SSL, Telnet server/SSH, ping, traceroute, Simple Network Time Protocol (SNTP), Trivial File Transfer Protocol (TFTP), SNMP, RADIUS, syslog, Domain Name System (DNS) client, Telnet Client, DHCP Client, DHCP Autoconfig, IPv6 DHCP Relay, Terminal Access Controller Access Control System Plus (TACACS+) IPv6 RFCs supported RFC 4443 (which obsoletes RFC2463): ICMP version 6 RFC 4291 (which obsoletes RFC 3513): IPv6 address architecture RFC 4291: IPv6 addressing architecture RFC 2460: IPv6 specification RFC 4861 (which obsoletes RFC 2461): neighbor discovery for IPv6 RFC 4862 (which obsoletes RFC 2462): IPv6 stateless address autoconfiguration RFC 1981: path MTU discovery RFC 4007: IPv6 scoped address architecture RFC 3484: default address selection mechanism RFC 5214 (which obsoletes RFC 4214): ISATAP tunneling RFC 4293: MIB IPv6: textual conventions and general group RFC 3595: textual conventions for IPv6 flow label ManagementCisco Business Dashboard Support for embedded probe for Cisco Business Dashboard running on the switch. Eliminates the need to set up a separate hardware or virtual machine for the Cisco Business Dashboard Probe on site. Cisco Business mobile app Mobile app for Cisco Business Switch and Wireless products. Helps to set up a local network in minutes and provide easy management at your fingertips. Cisco Network Plug and Play (PnP) agent The Cisco Network Plug and Play solution provides a simple, secure, unified, and integrated offering to ease new branch or campus device rollouts or for provisioning updates to an existing network. The solution provides a unified approach to provision Cisco routers, switches, and wireless devices with a near-zero-touch deployment experience Supports Cisco PnP Connect Web user interface Built-in switch configuration utility for easy browser-based device configuration (HTTP/HTTPS). Supports simple and advanced mode, configuration, wizards, customizable dashboard, system maintenance, monitoring, online help, and universal search SNMP SNMP versions 1, 2c, and 3 with support for traps, and SNMP version 3 User-based Security Model (USM) Remote Monitoring (RMON) Embedded RMON software agent supports 4 RMON groups (history, statistics, alarms, and events) for enhanced traffic management, monitoring, and analysis IPv4 and IPv6 dual stack Coexistence of both protocol stacks to ease migration Firmware upgrade Web browser upgrade (HTTP/HTTPS) and TFTP and upgrade over SCP running over SSH Dual images for resilient firmware upgrades Port mirroring Traffic on a port can be mirrored to another port for analysis with a network analyzer or RMON probe. Up to 8 source ports can be mirrored to one destination port. VLAN mirroring Traffic from a VLAN can be mirrored to a port for analysis with a network analyzer or RMON probe. Up to 8 source VLANs can be mirrored to one destination port. Flow-based redirection and mirroring Redirect or mirror traffic to a destination port or mirroring session based on flow Remote Switch Port Analyzer (RSPAN) Traffic can be mirrored across Layer 2 domain to a remote port on a different switch for easier troubleshooting sFlow agent Switch can export sFlow sample to external collectors. sFlow provides visibility into network traffic down to flow level DHCP (options 12, 59, 60, 66, 67, 82, 125, 129, and 150) DHCP options facilitate tighter control from a central point (DHCP server) to obtain IP address, autoconfiguration (with configuration and image file download), DHCP relay, and hostname Secure Copy (SCP) Securely transfer files to and from the switch Autoconfiguration with Secure Copy (SCP) file download Enables secure mass deployment with protection of sensitive data Text-editable config files Config files can be edited with a text editor and downloaded to another switch, facilitating easier mass deployment Smartports Simplified configuration of QoS and security capabilities Auto Smartports Applies the intelligence delivered through the Smartport roles and applies it automatically to the port based on the devices discovered over Cisco Discovery Protocol or LLDP-MED. This facilitates zero-touch deployments Textview CLI Scriptable command-line interface. A full CLI as well as a menu-based CLI is supported. User privilege levels 1, 7, and 15 are supported for the CLI Localization Localization of GUI and documentation into multiple languages Login banner Configurable multiple banners for web as well as CLI Other management Traceroute; single IP management; HTTP/HTTPS; SSH; RADIUS; port mirroring; TFTP upgrade; DHCP client; BOOTP; SNTP; Xmodem upgrade; cable diagnostics; ping; syslog; Telnet client (SSH secure support); automatic time settings from Management Station Green (power efficiency)Energy Detect Automatically turns power off on RJ-45 port when detecting link down. Active mode is resumed without loss of any packets when the switch detects the link up Cable length detection Adjusts the signal strength based on the cable length. Reduces the power consumption for shorter cables. EEE Compliant (802.3az) Supports IEEE 802.3az on all copper Gigabit Ethernet ports Disable port LEDs LEDs can be manually turned off to save on energy Time-based port operation Link up or down based on user-defined schedule (when the port is administratively up) Time-based PoE PoE power can be on or off based on user-defined schedule to save energy GeneralJumbo frames Frame sizes up to 9K bytes. The default MTU is 2K bytes MAC table 16K addresses DiscoveryBonjour The switch advertises itself using the Bonjour protocol Link Layer Discovery Protocol (LLDP) (802.1ab) with LLDP-MED extensions LLDP allows the switch to advertise its identification, configuration, and capabilities to neighboring devices that store the data in a MIB. LLDP-MED is an enhancement to LLDP that adds the extensions needed for IP phones Cisco Discovery Protocol The switch advertises itself using the Cisco Discovery Protocol. It also learns the connected device and its characteristics via Cisco Discovery Protocol Hardware Power Consumption (worst case)System power consumption 110V=124.1W 220V=124.5 Heat dissipation (BTU/hr) 424.8 PortsTotal system ports 20 x 10G copper + 4 x 10G copper/SFP+ combo + 1 x GE OOB management RJ-45 ports 20 x 10G copper Combo ports (RJ-45 + SFP) 4 x 10G copper/SFP+ combo Console port Cisco standard RJ45 console port USB slot USB Type-A slot on the front panel of the switch for easy file and image management Buttons Reset button Cabling type Unshielded Twisted Pair (UTP) Category 5e or better for 1000BASE-T LEDs System, Link/Act, PoE, Speed Flash 256 MB CPU 800 MHz ARM DRAM 512 MB Packet BufferPacket buffer (All numbers are aggregate across all ports as the buffers are dynamically shared:) 3 MB Supported SFP modulesSKU Media MGBSX1 Multimode fiber MGBLX1 Single-mode fiber MGBLH1 Single-mode fiber MGBT1 UTP cat 5e GLC-SX-MMD Multimode fiber GLC-LH-SMD Single-mode fiber GLC-BX-U Single-mode fiber GLC-BX-D Single-mode fiber GLC-TE UTP cat 5e SFP-H10GB-CU1M Copper coax SFP-H10GB-CU3M Copper coax SFP-H10GB-CU5M Copper coax SFP-10G-SR Multimode fiber SFP-10G-LR Single-mode fiber SFP-10G-SR-S Multimode fiber SFP-10G-LR-S Single-mode fiber EnvironmentalUnit dimensions (W x D x H) 440 x 350 x 44 mm (17.3 x 13.78 x 1.73 in) Unit weight 5.1 kg (11.2 lb) Power 100-240V 50-60 Hz, internal, universal Certifications UL (UL 62368), CSA (CSA 22.2), CE mark, FCC Part 15 (CFR 47) Class A Operating temperature 32° to 122°F (0° to 50°C) Storage temperature -13° to 158°F (-25° to 70°C) Operating humidity 10% to 90%, relative, noncondensing Storage humidity 10% to 90%, relative, noncondensing Acoustic Noise and Mean Time Between Failure (MTBF)Fan (number) 4 Acoustic noise 25°C: 41.2 dB MTBF @ 25°C (hours) 556642 Warranty Limited lifetime with next business day advance replacement Package contents Cisco Business 350 Series Managed Switch Power cord Mounting Kit Quick Start Guide Minimum Requirements Web browser: Chrome, Firefox, Edge, Safari Category 5e Ethernet network cable TCP/IP, network adapter, and network operating system (such as Microsoft Windows, Linux, or Mac OS X) installed

Objev podobné jako Cisco switch CBS350-24XT-EU (20x10GbE, 4x10GbE/SFP+ combo) - REFRESH

Záruka na dobu životnosti (99 let) + NBD po celou dobu životnosti + 3-letá 24x7 Softwarová podpora v ceně Rozsáhlá síť servisních středisek HP v ČR a na Slovensku JG936AR Před objednáním si vždy vyžádejte dostupnost (Pokud nejsou skladem u ATC). Podmínky na remarket trhu se mění velmi rychle. Pokud zboží není skladem, negarantujeme dostupnost ani cenu. Přehled - Management: Fully Managed - Layer 3 Dynamic: L2 switching / L3 Static routing / RIP routing - 24x 10/100/1000 RJ45 portů + 4x 1000/10000 SFP+ porty - Budget: 370W PoE+, (IEEE 802.3at) - IRF stacking (až 9 switchů do stohu) - Montáž do 19“ racku. Úchytky jsou součástí balení. I/O ports and slots 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only4 SFP+ fixed 1000/10000 SFP+ ports Additional ports and slots 1 RJ-45 serial console port Physical characteristics Dimensions17.32(w) x 11.81(d) x 1.72(h) in (44 x 30 x 4.37 cm) (1U height)Weight17.64 lb (8 kg) Memory and processor 1 GB SDRAM, 128 MB flash; packet buffer size: 1.5 MB Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance 1000 Mb Latency < 5 µs10 Gbps Latency < 1.5 µsThroughput 96 MppsRouting/Switching capacity 128 GbpsRouting table size 512 entries (IPv4), 256 entries (IPv6)MAC address table size 16384 entries Reliability MTBF (years) 48.3 Environment Operating temperature 32°F to 113°F (0°C to 45°C)Operating relative humidity 10% to 90%, noncondensingNonoperating/Storage temperature -40°F to 158°F (-40°C to 70°C)Nonoperating/Storage relative humidity 5% to 95%, noncondensingAcoustic Low-speed fan: 49.8 dB, High-speed fan: 52.9 dB; ISO 7779 Electrical characteristics Frequency 50/60 HzMaximum heat dissipation 102/1569 BTU/hr (107.61/1655.29 kJ/hr), for AC Power. For DC Power min heat dissipation is 85BTU/hr and max heat dissipation is 2559 BTU/hrAC voltage 100 - 240 VACCurrent 10 AMaximum power rating 460 WIdle power N/APoE power 370 W PoE+ Notes Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. PoE Power is the power supplied by the internal power supply. When supplemented with the use of an HP RPS1600 Redundant Power System, up to 740 W of PoE+ can be supplied.Max current rating for DC power is 25A. AC Input power is 30W typical, and 460W max(including 370W PoE+ consumption. DC Input voltage range is -54 to -57VDC. Total DC input power is 25W Typical and 790W with 740W PoE+ Power consumption. DC Input voltage range is -54VDC to -57VDC. DC Input Source is the HP RPS1600.SafetyUL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance Emissions EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A Immunity Generic EN 55024ESD EN300 386 Management IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager Services Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

Objev podobné jako HP 5130-24G-PoE+-4SFP+ (370W) EI Switch HP RENEW JG936A

HPE Aruba Networking CX 6100 48G Class4 PoE 4SFP+ 370W Switch RENEW JL675A Klíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE a až 370 W PoE třídy 4 pro podporu zařízení IoT. Kompaktní 12portový model bez ventilátoru pro tichý chod. Flexibilita správy s podporou Aruba Central, snadno použitelné webové grafické rozhraní, rozhraní CLI a Aruba NetEdit. Jednoduché nasazení s funkcí Zero Touch Provisioning. Připravenost na softwarovou definici s rozhraními REST API. Zjednodušení přidávání, přesunů a změn pomocí bezbarvého systému portů. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti. Specifications Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A) Description 48x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports Supports PoE Standards IEEE 802.3af, 802.3at 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (500W) Up to 370W of Class 4 PoE Power Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 30.48 cm (1.73" x 17.4" x 12.0") Configuration Weight 5.02 kg (11.07 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 176 Gbps Model Throughput Capacity 98.6 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.9 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 4.3 Bel Sound Pressure, LpAm (Bystander) = 29.8 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 4.9 A / 2.4 A Power Consumption (230 VAC) Idle: 30.6W Max Power (w/o PoE): 45W Max Power (w/ PoE): 480W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting

Objev podobné jako HPE Aruba Networking CX 6100 48G Class4 PoE 4SFP+ 370W Switch RENEW JL675A

Cisco CBS110-24PP: Spolehlivý a cenově dostupný switch REFRESH produkt - opravené nebo kvartálně rotované zařízení s plnou funkcionalitou, podporou a zárukou jako nové. Proč zvolit Cisco CBS110-24PP? Cisco CBS110-24PP je základním stavebním kamenem pro každou síť. Je ideální pro malé podniky na jakékoliv úrovni jejich růstu. Tento switch nabízí gigabitový Ethernet a funkce jako Power over Ethernet (PoE), energetickou efektivitu a prioritizaci provozu pro hladkou digitální transformaci. Výhody Cisco CBS110-24PP Plug-and-play: Není nutné mít IT znalosti nebo zákaznickou podporu. Cenově dostupný: Ideální pro malé firmy. Gigabitový Ethernet: A integrovaná QoS pro optimalizaci služeb citlivých na zpoždění a zlepšení celkového výkonu sítě. Úspora energie: Podpora standardu IEEE 802.3az optimalizuje využití napájení bez zásadního vlivu na výkon. Technické specifikace Počet portů: 24 Provedení: Desktop, Wall-mount nebo Rack-mount Porty: 24 x GbE RJ45, 2 x SFP combo, PoE Výkon: Switching capacity: 48 Gbps, Forwarding performance (64-byte packet size): 35.7 Mpps VLAN: Ne Standardy: IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3x, 802.3af Velikost MAC tabulky: 8 000 CPU paměť: 64 MB Flash: 8 MB Napájení: 110-240VAC, 50-60 Hz, internal, universal Rozměry (Š x V x H): 440 x 203 x 44 mm Hmotnost: 2.98 kg Provozní teplota: 0 až 40°C Provozní vlhost: 10 - 90% Skladovací teplota: -20 až 70 °C

Objev podobné jako Cisco switch CBS110-24PP (24xGbE, 2xGbE/SFP combo, 12xPoE+, 100W, fanless) - REFRESH

Aruba 6000 48G 4SFP Switch Aruba 6000 48G 4SFP Switch (R8N86A) je vysoce výkonný switch s pevnými napájecími zdroji a ventilátory. Porty 48x porty 10/100/1000BASE-T 4x 1G/1G SFP porty 1x USB-C Console Port 1x USB Type-A Host port Rozměry a hmotnost Switch má rozměry 4.39 cm (H) x 44.2 cm (W) x 24.74 cm (D) a váží 3.42 kg. Technické specifikace Dvojjádrový procesor ARM Cortex A9 @ 1016 Mhz 4 GB DDR3 paměť a 16 GB eMMC Packet Buffer: 12.38MB Switching kapacita: 104 Gbps Průchodnost: 77.3 Mpps Provozní podmínky Switch je navržen pro provoz v teplotách od 0°C do 45°C a vlhkosti 15% až 95% při 40°C. Elektrické charakteristiky Frekvence: 50 / 60 Hz AC Napětí: 100-127 VAC / 200-240 VAC Proud: 0.8 A / 0.5 A Spotřeba (230 VAC): Idle: 20.6W, Max Power: 44.2W Bezpečnost a emise Switch splňuje bezpečnostní normy UL 60950-1, IEC 60950-1, EN 60950-1 a další. Emissionský standard je VCCI-CISPR 32, Class A.

Objev podobné jako HPE Aruba Networking CX 6000 48G 4SFP Switch

Aruba Instant On 1830 24G 10/100/1000 2SFP Switch Aruba Instant On 1830 24G 10/100/1000 2SFP Switch. JL812A Aruba Instant On 1830 8G Switch (JL810A) Aruba Instant On 1830 8G 4p Class4 PoE 65W Switch (JL811A) Aruba Instant On 1830 24G 2SFP Switch (JL812A) Aruba Instant On 1830 24G 12p Class4 PoE 2SFP 195W Switch (JL813A) Aruba Instant On 1830 48G 4SFP Switch (JL814A) Aruba Instant On 1830 48G 24p Class4 PoE 4SFP 370W Switch (JL815A) I/O ports and slots 8 RJ-45 autosensing 10/100/1000 ports IEEE 802.3af Class 3 PD (port 1) (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 8 RJ-45 autosensing 10/100/1000 ports IEEE 802.3at Class 4 PoE (ports 1-4) (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 2 SFP 1GbE ports 24 RJ-45 autosensing 10/100/1000 ports IEEE 802.3at Class 4 PoE (ports 1-12) (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 2 SFP 1GbE ports 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP 1GbE ports 48 RJ-45 autosensing 10/100/1000 ports IEEE 802.3at Class 4 PoE (ports 1-24) (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP 1GbE ports Physical Characteristics Dimensions 157.0(d) x 173.0(w) x 39.1(h) mm 195.1(d) x 245.1(w) x 43.9(h) mm 215.9(d) x 443.0(w) x 43.9(h) mm 253.0(d) x 443.0(w) x 43.9(h) mm 253.0(d) x 443.0(w) x 43.9(h) mm 351.0(d) x 443.0(w) x 43.9(h) mm Weight 1.70 lb (0.77 kg) 3.40 lb (1.54 kg) 5.50 lb (2.49 kg) 7.65 lb (3.47 kg) 7.80 lb (3.54 kg) 10.90 lb (4.94 kg) Processor and Memory ARM Cortex-A9 @ 800MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5MB ARM Cortex-A9 @ 800MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5MB ARM Cortex-A9 @ 800MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5MB ARM Cortex-A9 @ 800MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5MB "RM Cortex-A9 @ 800MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5MB ARM Cortex-A9 @ 800MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5MB Aruba Instant On 1830 8G Switch (JL810A) Aruba Instant On 1830 8G 4p Class4 PoE 65W Switch (JL811A) Aruba Instant On 1830 24G 2SFP Switch (JL812A) Aruba Instant On 1830 24G 12p Class4 PoE 2SFP 195W Switch (JL813A) Aruba Instant On 1830 48G 4SFP Switch (JL814A) Aruba Instant On 1830 48G 24p Class4 PoE 4SFP 370W Switch (JL815A) Performance 100 Mb latency < 5.2 uSec < 5.2 uSec < 5.2 uSec < 5.2 uSec < 5.2 uSec < 5.2 uSec 1000 Mb latency < 2.8 uSec < 2.8 uSec < 2.8 uSec < 2.8 uSec < 2.8 uSec < 2.8 uSec 10000 Mb latency n/a n/a n/a n/a n/a n/a Throughput (Mpps) 11.90 Mpps 11.90 Mpps 38.68 Mpps 38.68 Mpps 77.37 Mpps 77.37 Mpps Capacity 16 Gbps 16 Gbps 52 Gbps 52 Gbps 104 Gbps 104 Gbps MAC address table size (# of entries) 8,000 entries 8,000 entries 16,000 entries 16,000 entries 16,000 entries 16,000 entries Reliability MTBF (years) 188.2 105.9 203.6 96.6 114.4 83.5 Environment Operating temperature 32°F to 104°F (0°C to 40°C) 32°F to 104°F (0°C to 40°C) 32°F to 104°F (0°C to 40°C) 32°F to 104°F (0°C to 40°C) 32°F to 104°F (0°C to 40°C) 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) 15% to 95% @ 104°F (40°C) 15% to 95% @ 104°F (40°C) 15% to 95% @ 104°F (40°C) 15% to 95% @ 104°F (40°C) 15% to 95% @ 104°F (40°C) Nonoperating/ storage temperature -40°F to 158°F (-40°C to 70°C) -40°F to 158°F (-40°C to 70°C) -40°F to 158°F (-40°C to 70°C) -40°F to 158°F (-40°C to 70°C) -40°F to 158°F (-40°C to 70°C) -40°F to 158°F (-40°C to 70°C) Nonoperating/ storage relative humidity 15% to 95% @ 140°F (60°C) 15% to 95% @ 140°F (60°C) 15% to 95% @ 140°F (60°C) 15% to 95% @ 140°F (60°C) 15% to 95% @ 140°F (60°C) 15% to 95% @ 140°F (60°C) Altitude up to 10,000 ft (3 km) up to 10,000 ft (3 km) up to 10,000 ft (3 km) up to 10,000 ft (3 km) up to 10,000 ft (3 km) up to 10,000 ft (3 km) Acoustics1 Fanless Fanless Fanless LWAd = 3.1 Bel LpAm (Bystander) = 17 dB LWAd = 3.4 Bel LpAm (Bystander) = 19 dB LWAd = 4.0 Bel LpAm (Bystander) = 25 dB Notes: 1Acoustics measured in 23°C semi-anechoic chamber with a loading of 100% traffic and (for JL813A and JL815A) 50% PoE on all ports. Measured in accordance with ISO 7779. Declared in accordance with ECMA-109:2010. Values presented are the Declared A-Weighted Sound Power Level (LWAd) and the mean Bystander A-Weighted Sound Pressure Level (LpAm) 100% traffic Fanless Fanless Fanless LWAd = 3.1 Bel LpAm (Bystander) = 17 dB LWAd = 3.4 Bel LpAm (Bystander) = 19 dB LWAd = 3.5 Bel LpAm (Bystander) = 20 dB 100% traffic / 0% PoE Fanless Fanless Fanless LWAd = 3.1 Bel LpAm (Bystander) = 17 dB - LWAd = 3.5 Bel LpAm (Bystander) = 20 dB 100% traffic / 50% PoE Fanless Fanless Fanless LWAd = 3.1 Bel LpAm (Bystander) = 17 dB - LWAd = 4.0 Bel LpAm (Bystander) = 25 dB 100% traffic / 100% PoE Fanless Fanless Fanless LWAd = 5.1 Bel LpAm (Bystander) = 35 dB - LWAd = 5.7 Bel LpAm (Bystander) = 41 dB Aruba Instant On 1830 8G Switch (JL810A) Aruba Instant On 1830 8G 4p Class4 PoE 65W Switch (JL811A) Aruba Instant On 1830 24G 2SFP Switch (JL812A) Aruba Instant On 1830 24G 12p Class4 PoE 2SFP 195W Switch (JL813A) Aruba Instant On 1830 48G 4SFP Switch (JL814A) Aruba Instant On 1830 48G 24p Class4 PoE 4SFP 370W Switch (JL815A) Electrical Characteristics Frequency 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz AC voltage 100-127VAC / 200- 240VAC 100-127VAC / 200- 240VAC 100-127VAC / 200- 240VAC 100-127VAC / 200- 240VAC 100-127VAC / 200- 240VAC 100-127VAC / 200- 240VAC Current 12V -- 1.0A 1.0A/0.5A 0.4A/0.3A 2.7A/1.4A 0.9A/0.6A 5.2A/2.6A Maximum power rating 100-127V: 8.09W 200-220V: 8.05W 100-127V: 86.07W 200-220V: 83.67W 100-127V: 19.1W 200-220V: 19W 100-127V: 244.6W 200-220V: 237.2W 100-127V: 40.2W 200-220V: 40W 100-127V: 462.5W 200-220V: 452.5W Idle power 100-127V: 5.8W 200-220V: 5.9W 100-127V: 8.3W 200-220V: 8.2W 100-127V: 7.6W 200-220V: 7.8W 100-127V: 14.5W 200-220V: 13.4W 100-127V: 17.7W 200-220V: 17.7W 100-127V: 25.8W 200-220V: 25.4W PoE power 13W max Class 3 PD 65 W Class 4 PoE - 195 W Class 4 PoE - 370 W Class 4 PoE Power supply External power adapter (included) Internal power supply Internal power supply Internal power supply Internal power supply Internal power supply Safety EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 EN/IEC 62368-1, 2nd. & 3rd. Ed. UL 62368-1, 2nd. & 3rd. Ed. CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed. EN/IEC 60825-1:2014 Class 1 EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 EN/IEC 62368-1, 2nd. & 3rd. Ed. UL 62368-1, 2nd. & 3rd. Ed. CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed. EN/IEC 60825-1:2014 Class 1 EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 EN/IEC 62368-1, 2nd. & 3rd. Ed. L 62368-1, 2nd. & 3rd. Ed. CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed. EN/IEC 60825-1:2014 Class 1 EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 EN/IEC 62368-1, 2nd. & 3rd. Ed. UL 62368-1, 2nd. & 3rd. Ed. CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed. EN/IEC 60825-1:2014 Class 1 EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 EN/IEC 62368-1, 2nd. & 3rd. Ed. UL 62368-1, 2nd. & 3rd. Ed. CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed. EN/IEC 60825-1:2014 Class 1 EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 EN/IEC 62368-1, 2nd. & 3rd. Ed. UL 62368-1, 2nd. & 3rd. Ed. CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed. EN/IEC 60825-1:2014 Class 1 Emissions EN 55032:2015/CISPR 32, Class A FCC CFR 47 Part 15: 2018 Class A ICES-003 Class A VCCI Class A CNS 13438 Class A KN 32 Class A AS/NZS CISPR 32 Class A EN 55032:2015/CISPR 32, Class A FCC CFR 47 Part 15: 2018 Class A ICES-003 Class A VCCI Class A CNS 13438 Class A KN 32 Class A AS/NZS CISPR 32 Class A EN 55032:2015/CISPR 32, Class A FCC CFR 47 Part 15: 2018 Class A ICES-003 Class A VCCI Class A CNS 13438 Class A KN 32 Class A AS/NZS CISPR 32 Class A EN 55032:2015/CISPR 32, Class A FCC CFR 47 Part 15: 2018 Class A ICES-003 Class A VCCI Class A CNS 13438 Class A KN 32 Class A AS/NZS CISPR 32 Class A EN 55032:2015/CISPR 32, Class A FCC CFR 47 Part 15: 2018 Class A ICES-003 Class A VCCI Class A CNS 13438 Class A KN 32 Class A AS/NZS CISPR 32 Class A EN 55032:2015/CISPR 32, Class A FCC CFR 47 Part 15: 2018 Class A ICES-003 Class A VCCI Class A CNS 13438 Class A KN 32 Class A AS/NZS CISPR 32 Class A Aruba Instant On 1830 8G Switch (JL810A) Aruba Instant On 1830 8G 4p Class4 PoE 65W Switch (JL811A) Aruba Instant On 1830 24G 2SFP Switch (JL812A) Aruba Instant On 1830 24G 12p Class4 PoE 2SFP 195W Switch (JL813A) Aruba Instant On 1830 48G 4SFP Switch (JL814A) Aruba Instant On 1830 48G 24p Class4 PoE 4SFP 370W Switch (JL815A) Immunity Generic EN 55035, CISPR 35, KN35 EN 55035, CISPR 35, KN35 EN 55035, CISPR 35, KN35 EN 55035, CISPR 35, KN35 EN 55035, CISPR 35, KN35 EN 55035, CISPR 35, KN35 EN EN 55035, CISPR 35 EN 55035, CISPR 35 EN 55035, CISPR 35 EN 55035, CISPR 35 EN 55035, CISPR 35 EN 55035, CISPR 35 ESD EN/IEC 61000-4-2 EN/IEC 61000-4-2 EN/IEC 61000-4-2 EN/IEC 61000-4-2 EN/IEC 61000-4-2 EN/IEC 61000-4-2 Radiated EN/IEC 61000-4-3 EN/IEC 61000-4-3 EN/IEC 61000-4-3 EN/IEC 61000-4-3 EN/IEC 61000-4-3 EN/IEC 61000-4-3 EFT/Burst EN/IEC 61000-4-4 EN/IEC 61000-4-4 EN/IEC 61000-4-4 EN/IEC 61000-4-4 EN/IEC 61000-4-4 EN/IEC 61000-4-4 Surge EN/IEC 61000-4-5 EN/IEC 61000-4-5 EN/IEC 61000-4-5 EN/IEC 61000-4-5 EN/IEC 61000-4-5 EN/IEC 61000-4-5 Conducted EN/IEC 61000-4-6 EN/IEC 61000-4-6 EN/IEC 61000-4-6 EN/IEC 61000-4-6 EN/IEC 61000-4-6 EN/IEC 61000-4-6 Power frequency magnetic field EN/IEC 61000-4-8 EN/IEC 61000-4-8 EN/IEC 61000-4-8 EN/IEC 61000-4-8 EN/IEC 61000-4-8 EN/IEC 61000-4-8 Voltage dips and interruptions EN/IEC 61000-4-11 EN/IEC 61000-4-11 EN/IEC 61000-4-11 EN/IEC 61000-4-11 EN/IEC 61000-4-11 EN/IEC 61000-4-11 Harmonics EN/IEC 61000-3-2 EN/IEC 61000-3-2 EN/IEC 61000-3-2 EN/IEC 61000-3-2 EN/IEC 61000-3-2 EN/IEC 61000-3-2 Flicker EN /IEC 61000-3-3 EN /IEC 61000-3-3 EN /IEC 61000-3-3 EN /IEC 61000-3-3 EN /IEC 61000-3-3 EN /IEC 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Aruba Instant On Cloud; Web browser; SNMP Manager Aruba Instant On Cloud; Web browser; SNMP Manager Aruba Instant On Cloud; Web browser; SNMP Manager Aruba Instant On Cloud; Web browser; SNMP Manager Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounting positions and supported racking Supports table-top mounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using base surface mounting holes Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rack-mounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Must be mounted top surface up. To prevent possible impact to longterm reliability, product should not be mounted upside-down Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rack-mounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Must be mounted top surface up. To prevent possible impact to longterm reliability, product should not be mounted upside-down Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rack-mounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rack-mounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rack-mounting Supports wall-mounting with ports facing either up or down Suports under-table mounting using the brackets provided Aruba Instant On 1830 8G Switch (JL810A) Aruba Instant On 1830 8G 4p Class4 PoE 65W Switch (JL811A) Aruba Instant On 1830 24G 2SFP Switch (JL812A) Aruba Instant On 1830 24G 12p Class4 PoE 2SFP 195W Switch (JL813A) Aruba Instant On 1830 48G 4SFP Switch (JL814A) Aruba Instant On 1830 48G 24p Class4 PoE 4SFP 370W Switch (JL815A) Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba 1G SFP RJ45 T 100m Cat5e Transceiver (J8177D) Aruba 1G SFP RJ45 T 100m Cat5e Transceiver (J8177D) Aruba 1G SFP RJ45 T 100m Cat5e Transceiver (J8177D) Aruba 1G SFP RJ45 T 100m Cat5e Transceiver (J8177D) Standards and Protocols (applies to all products in series) IEEE Standards Support IEEE 802.3 10 Mbps Ethernet IEEE 802.3u 100Base-T Ethernet IEEE 802.3z 1000 Mbps Ethernet IEEE 802.3ab 1000Base-T IEEE 802.3x Flow Control IEEE 802.1Q VLANs IEEE 802.1p Traffic Prioritization IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.3af PoE 1 (PoE models only) IEEE 802.3at PoE 1 (PoE models only) IEEE 802.3az Energy-Efficient Ethernet (EEE) IEEE 802.1AB Link Layer Discovery Protocol IEEE 802.3ac Frame extension for VLAN tags

Objev podobné jako HPE Networking Instant On Switch 24p Gigabit 2p SFP 1830

TP-Link switch TL-SG1210MP 10portový gigabitový stolní switch s 8 porty PoE+ 9 gigabitových portů RJ45 a 1 kombinovaný gigabitový port SFP/RJ45. 8 portů PoE+ přenáší data i napájení přes jediný kabel a disponují celkovým rozpočtem napájení 123 W. Switch vyhovuje standardu IEEE 802.3af/at PoE+ a podporuje napájení PoE s výkonem až 30 W na každém portu PoE. Přenos dat a napájení na vzdálenost až 250 m v rozšířeném režimu. Prioritní režim poskytuje vysokou prioritu portům 1–2, aby byl zajištěn kvalitní provoz citlivých aplikací. Režim izolace umožňuje jedním kliknutím oddělit přenos dat klientů k zajištění vyššího zabezpečení a výkonu. S funkcí automatického obnovení PoE automaticky restartuje vypadlá nebo nereagující zařízení napájená přes PoE. Zapojení „Plug and Play“ bez nutnosti konfigurace Konstrukce bez ventilátoru snižuje spotřebu energie a zajišťuje tichý provoz v místě instalace. Stránky produktu: https://www.tp-link.com/cz/business-networking/unmanaged-switch/tl-sg1210mp/ Technické specifikace Více informací o TP-Link PoE technologii > HARDWARE FEATURES Interface • 9× 10/100/1000 Mbps RJ45 Ports • 1× 1000 Mbps Combo SFP/RJ45 Port • AUTO Negotiation • AUTO MDI/MDIX Network Media • 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) • EIA/TIA-568 100? STP (maximum 100m) • 100BASE-TX: UTP category 5, 5e cable (maximum 100m) • EIA/TIA-568 100? STP (maximum 100m) Fan Quantity Fanless Physical Security Lock Yes External Power Supply External Power Adapter (Output: 53.5VDC / 2.43A) Packet Forwarding Rate 14.88 Mpps PoE Ports (RJ45) • Standard: 802.3 af/at compliant • PoE Ports: Ports 1–8 • Power Supply: 123 W Mac Address Table 4K Jumbo Frame 16 KB Switching Capacity 20 Gbps Dimensions ( W x D x H ) 8.2 × 4.9 × 1.0 in (209 × 126 × 26 mm) Max Power Consumption • 7.93 W (220V / 50Hz with no PD connected) • 141.40 W (220V / 50Hz with 123 W PD connected) Max Heat Dissipation • 27.04 BTU/h (220V / 50Hz with no PD connected) • 482.17 BTU/h (220V / 50Hz with 123 W PD connected) SOFTWARE FEATURES Transmission Method Store-And-Forward Advanced Functions • Compatible With IEEE 802.3af/at Compliant PDs • Extend Mode Button (Ports 1–4, Up to 250 m PoE power supply and data transmission) • Priority Mode Button (Ports 1–2) • Isolation Mode Button (Ports 1–4 / 5-8) • PoE Auto Recovery (Ports 1-8) • Mac Address Auto-Learning and Auto-Aging • IEEE802.3x Flow Control For Full-Duplex Mode And Backpressure for Half-Duplex Mode OTHERS Certification FCC, CE, RoHS Package Contents • TL-SG1210MP • Power Adapter • Installation Guide Environment • Operating Temperature: 0–40 °C (32–104 °F) • Storage Temperature: -40–70 °C (-40–158 °F) • Operating Humidity: 10–90% RH non-condensing • Storage Humidity: 5–90% RH non-condensing

Objev podobné jako TP-Link CCTV switch TL-SG1210MP (8xGbE, 1xGbE uplink, 1xGbE/SFP combo uplink, 8x PoE+, 123W, fanless)

Aruba Instant On 1930 48G 4SFP/SFP+ Switch EAN: 190017356112 Porty a sloty 48 RJ-45 autosensing 10/100/1000 portů 4 SFP+ 1/10GbE porty Fyzické charakteristiky Rozměry: 44,2(w) x 28,2(d) x 4,4(h) cm Hmotnost: 3.13 kg Výkon CPU: ARM Cortex-A9 @ 800 MHz Paměť a flash: 512 MB SDRAM, 256 MB flash Buffer paketů: 1.5 MB Latence 100 Mb: < 4.5 uSec Latence 1000 Mb: <2.2 uSec Latence 10000 Mb: <1.2 uSec Průtok (Mpps): 130.95 Mpps Kapacita: 176 Gbps Provozní podmínky Provozní teplota: 0°C až 40°C Provozní vlhkost: 15% až 95% při 40°C Nepracovní teplota: -40°C až 70°C Nepracovní vlhkost: 15% až 95% při 60°C Výška: do 3.048 Km Elektrické charakteristiky Frekvence: 50-60 Hz AC napětí: 100 - 127 / 200 - 240 VAC Proud: .8 A/.5 A Maximální výkon: 36.9 W Nečinný výkon: 16.8 W Správa zařízení Aruba Instant On Cloud; Webový prohlížeč; SNMP Manager Montáž Montáž do standardního 19" telco racku nebo skříňky. Sada pro montáž do 2-post racku je součástí balení. Podporuje montáž na stůl Podporuje montáž na stěnu s porty směřujícími nahoru nebo dolů Podporuje montáž pod stůl pomocí přiložených držáků Transceivery Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A ) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E)

Objev podobné jako HPE Networking Instant On Switch 48p Gigabit 4p SFP+ 1930 (JL685A)

Aruba Instant On 1930 8G 2SFP Switch Aruba Instant On 1930 je řada přepínačů pro malé a rostoucí podniky. Je ideální pro podporu aplikací náročných na šířku pásma. Snadno se integruje se stávajícími přepínači a přístupovými body. Může být centrálně spravována pomocí mobilní aplikace Instant On. Funkce Aruba Instant On 1930 nabízí snadné použití a nasazení typu "plug-and-play". Lze ji nasadit pomocí dvou způsobů - Instant On cloud-management nebo mobilní aplikace. Podporuje energeticky účinný Ethernet pro nižší spotřebu energie. Nabízí rozšířenou sadu funkcí pro robustnější provoz. Specifikace Porty 8 RJ-45 10/100/1000 2 SFP 1GbE ports Paměť a procesor ARM Cortex-A9 @ 800 MHz 512 MB SDRAM, 256 MB flash 1.5 MB packet buffer Propustnost 14.88 Mpps, maximum Přepínací kapacita 20 Gbps Funkce pro správu Aruba Instant On Portal, Web browser, SNMP Manager Vstupní napětí 100 - 240 VAC Spotřeba energie 11.0 W maximum, 6.2 W idle Rozměry 4.39 x 25.4 x 15.95 cm Váha 0.82 kg PoE -

Objev podobné jako HPE Networking Instant On Switch 8p Gigabit 2p SFP 1930 (JL680A)

Aruba Instant On 1960 12XGT 4SFP+ Switch Kód produktu: JL805A EAN: 190017521770 Specifikace: Porty: 12 RJ-45 autosensing 100/1000/10GBASE-T ports SFP+ porty: 4 SFP+ 10GbE ports Rozměry a hmotnost: Rozměry: 350.5(d) x 442.5(w) x 43.95(h) mm Hmotnost: 9.6 lb (4.3 kg) Výkon: Procesor: Single Core ARMv7 Cortex-A9 @2Ghz Latence: 100 Mb Latency < 7.4 uSec, 1000 Mb Latency < 4.2 uSec, 10000 Mb Latency < 1.1 uSec Průtok: 238 Mpps Kapacita: 320 Gbps Tabulka velikosti: Statické záznamy: 512 IPv4/IPv6 Velikost tabulky MAC adres: 16,000 entries Bezpečnost: Normy: EN/IEC 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, EN/IEC 62368-1, 2nd. & 3rd. Ed., UL 62368-1, 2nd. & 3rd. Ed., CAN/CSA C22.2 No. 62368-1, 2nd. & 3rd. Ed., EN/IEC 60825-1:2014 Class 1 Elektrické charakteristiky: Frekvence: 50Hz/60Hz AC napětí: 100-127VAC / 200-240VAC Proud: 1.3A/0.4A Maximální výkon: 100-127V: 130W 200-220V: 160W Správa zařízení: Aruba Instant On Cloud; Web browser; SNMP Manager Možnosti montáže: Montáž v EIA-standard 19 in. telco rack nebo skříni Podpora montáže na stůl Podpora montáže na zeď s porty směřujícími nahoru nebo dolů Podporované transceivery: Aruba 1G SFP LC SX 500m MMF Transceiver (J4858D) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba 1G SFP RJ45 T 100m Cat5e Transceiver (J8177D) Aruba 10G SFP+ LC SR 300m MMF Transceiver (J9150D) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) Aruba 10G SFP+ to SFP+ 1m DAC (J9281D) Aruba 10G SFP+ to SFP+ 3m DAC (J9283D)

Objev podobné jako HPE Networking Instant On Switch 12p 10GBT 4p SFP+ 1960 (JL805A)

Switch 18 portový, 100 Mbit, PoE, desktop Není vyplněn Alternativní text k fotografii! Switch CUDY Získejte až 16 portů, které vám umožní využívat PoE napájení (vyhovuje standardu IEEE 802.3at / IEEE 802.3af). Budete moci ve vašem okolí provozovat například přístupový bod, VoIP telefony, tiskárny nebo IP kamery. Switch CUDY umožňuje až 30W napájení na každém portu, přičemž celkový napájecí výkon na všech portech nesmí přesáhnout 200 W. Není vyplněn Alternativní text k fotografii! Není vyplněn Alternativní text k fotografii!...

Objev podobné jako CUDY 16-Port 10/100M PoE+ Switch with 1Gigabit Uplink and 1 Gigabit Combo SFP Port 200W (FS1018PS1 )

TP-Link switch TL-SG1210MPE Výkonný 10portový gigabitový Easy Smart switch Plná kompatibilita s PoE zařízeními Perfektní pro IP kamery, přístupové body, IP telefony i počítače a tiskárny. 9 gigabitových portů a 1 kombinovaný gigabitový port Osazen 8 porty 802.3af/at PoE+ s výkonem napájení až 30 W na port. Účinné napájení PoE Celkový výkon až 123 W ze všech portů PoE. Monitorování sítě a řízení provozu Podporuje funkce VLAN a automatické obnovení PoE. Jednoduché nastavení a připojení Plug-and-play připojení a jednoduché nastavení přes webové rozhraní. Nízká spotřeba energie Konstrukce bez ventilátoru snižuje spotřebu energie a eliminuje provozní hlučnost. Technické specifikace Standardy a protokoly: IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3x, IEEE 802.1q, IEEE 802.1p, IEEE 802.3at, IEEE 802.3z Rozhraní: 9× 10/100/1000 Mbps RJ45 Ports, 1× 1000 Mbps Combo SFP/RJ45 Port, AUTO Negotiation/AUTO MDI/MDIX Příkon: 7.66 W (220V / 50Hz bez připojení PD), 141.54 W (220V / 50Hz s připojením 123 W PD) Rozměry: 8.2 × 4.9 × 1.0 in (209 × 126 × 26 mm) Switching kapacita: 20 Gbps Přenosová rychlost paketů: 14.88 Mpps MAC adresa tabulka: 4 K Jumbo Frame: 16 KB Software Kvalita služby: Podpora Port-Based/802.1p/DSCP priority L2 vlastnosti: IGMP Snooping V1/V2/V3, Static Link Aggregation, Port Mirroring, Cable Diagnostics, Loop Prevention VLAN: Podpora až 32 VLANů současně (z 4K VLAN IDů) PoE: Extend Mode, PoE Auto Recovery Správa: Webové GUI, Easy Smart Configuration Utility Certifikace FCC, CE, RoHS Obsah balení TL-SG1210MPE Napájecí adaptér Instalační průvodce Gumové nožičky Systémové požadavky Microsoft Windows pro běh Utility Provozní podmínky Provozní teplota: 0°C~40°C, Skladovací teplota: -40°C~70°C, Provozní vlhkost: 10%~90%RH nekondenzující, Skladovací vlhkost: 5%~95%RH nekondenzující

Objev podobné jako TP-Link CCTV Easy Smart switch TL-SG1210MPE (8xGbE, 1xGbE uplink, 1xGbE/SFP combo uplink, 8xPoE+, 123W, fanless)

Switch 48 portový, 1 Gbit, 4× SFP, QoS, VLAN, spravovatelný, rack Switch je aktivní síťový komponent propojující jednotlivá zařízení případně jiné prvky sítě. Slouží ke správě síťového provozu. Aruba IOn 1930 48G 4SFP+ Switch je určen k instalaci do rozvaděče. Nabízený model vás zaujme přepínací kapacitou 176 Gb/s a paketovou kapacitou 130,95 ks. Switch disponuje 48 ks RJ-45 portů, které jsou určeny k propojení se síťovými prvky. Celkem 4 konektory typu SFP využijete k přenosu dat přes optická vlákna. Technologie 10/100/1000Base-T dokáže šířit data až při rychlosti 1000 Mbit/s. Využívá Dual Personality porty, které vynikají tím, že je jejich součástí konektor RJ-45 i SFP, v konkrétním okamžiku lze však použít jen jeden z nich. Rozměry switche odpovídají hodnotám 442,5 × 282,4 × 43,9 mm. Díky technologii QoS neboli Quality of Service nedojde k zahlcení switche, dokonce si můžete seřídit přednost koncových zařízení. Tento switch navíc nabízí schopnost...

Objev podobné jako Aruba IOn 1930 48G 4SFP+ Switch (JL685A)

HPE FlexNetwork 5130 24G 4SFP+ 1-slot HI Switch (Must select min 1 power supply) JH323A RENEW

Objev podobné jako HPE FlexNetwork 5130 24G 4SFP+ 1-slot HI Switch (Must select min 1 power supply jd362B) JH323A RENEW

Aruba 6200F 24G 4SFP+ Switch JL724A RENEW Klíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE a až 370 W PoE třídy 4 pro podporu zařízení IoT. Inteligentní monitorování, přehled a řešení problémů s nástrojem Aruba Network Analytics Engine. Jednoduché nasazení jedním dotykem pomocí Aruba CX mobilní aplikací. Zabezpečený a jednoduchý přístup pro uživatele a IoT s technologií Aruba Dynamic Segmentation. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti.

Objev podobné jako Aruba 6200F 24G 4SFP+ Switch JL724A RENEW

Aruba Instant On 1930 8G Class4 PoE 2SFP 124W Switch EAN: 190017355238 Obecný popis Aruba Instant On 1930 switch je vysoce výkonný, inteligentně spravovaný switch navržený s ohledem na malé podniky. Nabízí snadnou implementaci a cenovou dostupnost. Zvládá dnešní aplikace s velkým objemem dat, jako je hlasová a video konference. Porty a sloty 8 portů RJ-45 autosensing 10/100/1000 Class 4 PoE 2 porty SFP 1GbE Tělesné charakteristiky Rozměry: 25.4 x 15.95 x 4.39 cm Váha: 1.16 kg Procesor a paměť ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5 MB Výkon Průchodnost: 14.88 Mpps Kapacita: 20 Gbps Prostředí Provozní teplota: 0°C to 40°C Relativní vlhkost při provozu: 15% to 95% @ 40°C Elektrické charakteristiky Frekvence: 50-60 Hz AC napětí: 100 - 127 / 200 - 240 VAC PoE výkon: 124 W Class 4 PoE Bezpečnost Dodržuje bezpečnostní normy jako UL 60950-1, IEC 60950-1, EN 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60825-1. Správa zařízení Správa přes Aruba Instant On Cloud, webový prohlížeč, SNMP Manager. Montáž Podporuje montáž v racku, na stůl, na zeď, pod stůl pomocí dodaných držáků. Transceivery Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF XCVR (J4859D) Aruba 1G SFP RJ45 T 100m Cat5e XCVR (J8177D) Klíčové vlastnosti Smart-managed layer 2+ Ethernet switch series PoE k napájení AP a IoT zařízení Bezpečnostní kontroly pro ochranu dat Snadná mobilní aplikace a webové GUI pro nastavení, správu a řešení problémů. Standardní funkce Jednoduchost na prvním místě Bezpečnost, na kterou se můžete spolehnout Podpora, na kterou se můžete spolehnout Diferenciátory Instant On Snadné nastavení a správa Neagresivní, estetický design Vysoký výkon s flexibilními možnostmi Optimalizovaný uživatelský zážitek Inventář místa Správa více míst Integrovaná bezpečnost Žádné skryté poplatky Správa Cloudová správa pro celou síť Jednoduché lokální webové GUI správa Aktualizace firmwaru Výchozí režim klienta DHCP Mirroring portů Protokolování událostí a upozornění Správa účtů LED lokalizátor Kvalita služeb (QoS) Prioritizace provozu IEEE 802.1p/Q VLAN tagging Třída služby (CoS) Pokročilý klasifikátor na základě QoS Přepínání přístupu SFP/SFP+ vláknová konektivita Class 4 PoE (PoE+; IEEE 802.3at) Automatické konfigurace PoE výkonu Přidělení výkonu PoE Auto MDI/MDI-X Síťová bezpečnost Zabezpečení na základě TPM Podpora IEEE 802.1Q VLAN Ověřování přístupu IEEE 802.1X Automatická ochrana proti DoS Ochrana proti bouři paketů RADIUS RADIUS účtování ID správní VLAN Ochrana před fluktuací linky Výkon a účinnost Energeticky účinný Ethernet (EEE) Automatické vypnutí portu Status úspor energie Energeticky účinné chlazení Bez ventilátoru Přepínací funkce IEEE 802.3x Flow control Spanning Tree Protocol (STP) Ochrana proti smyčkám Filtrování BPDU Podpora jumbo rámů IGMP snooping v1/v2 Linková agregace LLDP/LLDP-MED (Media Endpoint Discovery) Address Resolution Protocol (ARP) Záruka, servis a podpora Aruba Instant On Limited Lifetime Support poskytuje 24x7 telefonickou podporu po dobu prvních 90 dnů a chatovou podporu po celou dobu záruky. Komunitní podpora je zahrnuta po celou dobu životnosti produktu.

Objev podobné jako HPE Networking Instant On Switch 8p Gigabit CL4 PoE 2p SFP 124W 1930

Aruba Instant On 1960 48G 2XGT 2SFP+ Switch Specifikace EAN: 190017522616 I/O porty a sloty: 48 RJ-45 autosensing 10/100/1000 Mbps portů 2 SFP+ 10GbE porty 2 10GBASE-T porty Rozměry: 350.5(d) x 442.5(w) x 43.95(h) mm Hmotnost: 4.4 kg Procesor: Single-Core ARM v7 Cortex-A9 @800MHz Výkon Latence 100 Mb:

Objev podobné jako HPE Networking Instant On Switch 48p Gigabit 2p 10GBT 2p SFP+ 1960 (JL808A)

Klíčové vlastnosti Konektivita na vrstvě 2 s podporou pro ACL, robustní QoS a statické směrování. Integrované uplinky 1/10GbE a až 370 W PoE třídy 4 pro podporu zařízení IoT. Kompaktní 12portový model bez ventilátoru pro tichý chod. Flexibilita správy s podporou Aruba Central, snadno použitelné webové grafické rozhraní, rozhraní CLI a Aruba NetEdit. Jednoduché nasazení s funkcí Zero Touch Provisioning. Připravenost na softwarovou definici s rozhraními REST API. Zjednodušení přidávání, přesunů a změn pomocí bezbarvého systému portů. Bezpečnost Podpora seznamu řízení přístupu (ACL) pro IPv4 i IPv6; umožňuje filtrovat provoz a zabránit tak neoprávněným uživatelům přístup k síti nebo k řízení sítě. Filtrování zdrojových portů umožňuje pouze zadaným portům komunikovat mezi sebou. Zabezpečený FTP umožňuje bezpečný přenos souborů do switche a z něj a chrání před nežádoucím stahováním souborů nebo jejich přenosem. Secure shell šifruje všechna přenášená data, aby byla bezpečná pro vzdálený přístup k CLI přes IP sítě. Zablokování adresy MAC zabraňuje tomu, aby se konkrétní adresa MAC nemohla připojit k síti. Specifications Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A) Description 48x ports 10/100/1000BASE-T Ports 4x 1G/10G SFP ports Supports PoE Standards IEEE 802.3af, 802.3at 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply (500W) Up to 370W of Class 4 PoE Power Fans Fixed fans Physical characteristics Dimensions (H) 4.39 cm (W) 44.2 cm (D) 30.48 cm (1.73" x 17.4" x 12.0") Configuration Weight 5.02 kg (11.07 lbs) Additional Specifications CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Performance Model Switching Capacity 176 Gbps Model Throughput Capacity 98.6 Mpps Average Latency (LIFO-64- bytes packets) 1 Gbps: 1.9 µSec , 10 Gbps: 1.8 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 4.3 Bel Sound Pressure, LpAm (Bystander) = 29.8 dB Primary Airflow Side-to-side Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 4.9 A / 2.4 A Power Consumption (230 VAC) Idle: 30.6W Max Power (w/o PoE): 45W Max Power (w/ PoE): 480W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Aruba 6100 48G Class4 PoE 4SFP+ 370W Switch (JL675A)) Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting

Objev podobné jako HPE Aruba Networking CX 6100 48G Class4 PoE 4SFP+ 370W Switch JL675A

High-Performance, Smart-Managed Switches Designed with Small Businesses in Mind Whether you own a cafe, a design firm or a tech startup, a reliable and secure network plays a critical role in the success of your business. And you need a network solution that gives you peace of mind, allowing you to focus on growing your business instead of managing problems with your network. Aruba Instant On makes it easy to keep network users happy, mobile and IoT devices connected, and your network secure. The Aruba Instant On 1930 switches features advanced, smart-managed, fixed- configuration Gigabit switches designed for small businesses that are easy-to-deploy and affordable. They're made to handle today's bandwidth-heavy applications like voice and video conferencing, enabling consistent connectivity to enhance performance. Using either the Instant On mobile app or the cloud-based web portal, you can quickly set up, monitor and manage the 1930 switch series from anywhere at any time. What's more, up to 30 W PoE power delivery is available out-of-the-box for your class 4 PoE devices, like access points, surveillance cameras and VoIP phones, all easily managed from the same platform. Built-in security features protect your network from unauthorized access by allowing you to segment traffic and define access to each area of the network. And all of this is included in the price of the hardware - there are no hidden subscription or licensing fees. Key Features Smart-managed layer 2+ Ethernet switch series ready to deploy in 8-, 24-and 48-port for non-PoE and Class 4 PoE models PoE to power APs and IoT devices like IP phones, surveillance cameras and door locks Two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models to eliminate traffic bottlenecks across your network Security controls let you define access in each area of your network, keeping your business data safe Convenient mobile app and web- based GUI for set up, management and troubleshooting. Standards and Protocols (applies to all products in series) IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3z 1000BASE-X IEEE 802.2af PoE 1 (PoE models only) IEEE 802.3at PoE 1 (PoE models only) IEEE 802.3x Flow control IEEE 802.1Q VLANS IEEE 802.1p Priority IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.1X Port Access Authentication IEEE 802.3az Energy Efficient Ethernet IEEE 802.1D: Spanning Tree Protocol IEEE 802.1W: Rapid Spanning Tree Protocol IEEE 802.1S: Multiple Spanning Tree Protocol IEEE 802.1AB Link Layer Discovery Protocol Denial of service protection CPU DoS protection Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 370W Switch (JL684B) I/O Ports and Slots 24 RJ-45 autosensing 10/100/1000 Class 4 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 10.42(d) x 1.73(h) in (44.25 x 26.47 x 4.39 cm) (1U height) Weight 8.23 lb (3.73 kg) Processor and Memory ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5 MB Memory And Flash 512 MB SDRAM 256 MB flash Packet Buffer 1.5 MB Performance 100 Mb latency < 4.7 uSec 1000 Mb latency 10000 Mb latency Throughput (Mpps) 95.23 Mpps Capacity 128 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 71 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic1 LWAd = 4.0 Bel LpAm (Bystander) = 24 dB Notes: 1Acoustics measured in 23°C semi-anechoic chamber with a loading of 100% traffic and 50% PoE on all ports. Measured in accordance with ISO 7779. Declared in accordance with ECMA-109:2010. Values presented are the Declared A-Weighted Sound Power Level (LWAd) and the mean Bystander A-Weighted Sound Pressure Level (LpAm) Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current 4.9 A/2.4 A Maximum power rating 440.4W Idle power 20.3W PoE power 370 W Class 4 PoE Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) Standard Features Simplicity at Its Best Plug-and-play switches that work together with Instant On APs right out of the box Mobile app to easily setup, monitor and manage your network Security You Can Count On Protect your network from unauthorized access with IEEE 802.1X and VLANs Automatic denial-of-service (DOS) monitors and protects the network against malicious attacks We've Got You Covered No extra licensing or subscription fees Industry-leading limited lifetime warranty and support. The Instant On Differentiators Easy Setup and Management The Aruba Instant On mobile app allows you to set up, manage, and monitor Instant On switches and access points directly from your phone. Within the app, you get guided step-by-step instructions to install Instant On devices to get your network up and running quickly - no technical expertise required. And cloud-based access allows you to access the network from anywhere, at any time. Non-intrusive, Aesthetic Design Aruba Instant On switches are designed to complement the sleek and clean look of the Instant On access points, and to blend discreetly into your site's environment. The 8-port models, as well as the 24- and 48-port non PoE models, are fan-less, making them ideal for quiet office deployments. High Performance with Flexible Options The series consists of four (4) Class 4 PoE switches, and three (3) non-PoE switches including 8- 24- and 48-port Gigabit Ethernet switches. The two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models, ensure high performance and eliminate traffic bottlenecks across the network. Customizable features include basic Layer 2 features like VLANs and link aggregation, as well as advanced features such as Layer 3 IPv4 static routing, ACLs, and Spanning Tree Protocols, and IPv6 Host mode. Optimized User Experience The Aruba Instant On mobile app provides common workflows for Instant On switches and access points making it easier to configure, monitor and manage your network remotely without the need for additional hardware like cloud keys or VPN. You can also update firmware on your Instant On devices directly from the cloud whenever you want, from wherever you are. Site inventory The site inventory feature on the Instant On mobile app shows you all switches and AP's on a single screen, allowing you to quickly identify non-functioning devices and troubleshoot accordingly. Multi-Site Management The cloud-hosted web interface and mobile app make it easy to manage multiple sites, multiple networks, distributed deployments and multi-tenant deployments. Each site is logically separated and has its own configuration, statistics, guest portal, and admin read/write privileges. Built-In Security Built-in security features protect your network from external threats by blocking malware attacks and keeping unauthorized users off the network. Network traffic can be filtered and access restricted based on MAC and IP address. No Hidden Fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry leading limited lifetime warranty are also included, along with chat support for the life of the product. Management Cloud-Based Management for Entire Network The cloud-hosted web interface and mobile app make it easy to manage networks with Instant On APs and Switches. Simple Local Web GUI Management For management of individual switches, the intuitive Web GUI makes management simple, even for non-technical users. Supports up to five (5) HTTP and HTTP Secure (HTTPS) sessions. Firmware Update Provides notification of the latest firmware with the ability to schedule update at a preferred time through Instant On mobile app and cloud-based web portal. Default DHCP Client Mode Allows the switch to be directly connected to a network, enabling plug-and-play operation. In the absence of a DHCP server on the network, the switch falls back to the static address 192.168.1.1. Port Mirroring Enables traffic on a port or VLAN to be simultaneously sent to a network analyzer for monitoring. Event Logging and Alerts Provides detailed information for problem identification and resolution. Account Management Allows administrators to add, modify, delete and transfer management accounts and passwords for secure access to Instant cloud management solution. Locator LED Allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches. Schedule Configuration Global Schedule feature can be applied to time-based ACLs, port or interface shutdown, or PoE power delivery; up to 3 schedules can be configured. PoE scheduling allows user to configure a specific day/time of the week (e.g. business hours) for Instant On switches to supply power to connected devices (e.g. surveillance cameras, access points etc.). Quality of Service (QoS) Traffic Prioritization Provides time-sensitive packets (like VoIP and video) with priority over other traffic based on DSCP or IEEE 802.1p classification. IEEE 802.1p/Q VLAN Tagging Delivers data to devices based on the priority and type of traffic; supports IEEE 802.1Q. Class of Service (CoS) Sets the IEEE 802.1p/DSCP priority to queue mapping (4 queues). Supports strict priority queuing (SP) or weighted round robin (WRR) queuing. SP and WRR queuing can be configured on individual switch ports. Advanced Classifier Based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information. Access Switching SFP/SFP+ Fiber Connectivity Provides fiber connections for uplinks and other connections across longer distances than copper cabling can support. SFP ports are in addition to available copper Ethernet ports, providing a higher total number of available ports. Two (2) SFP 1G ports available on 8-port models and four (4) SFP+ 1G/10G ports on 24-/48 port models. Ethernet Alliance Certified Class 4 PoE (IEEE 802.3at) Provides up to 30 W per port, which allows support of the class 4 PoE capable devices such as video IP phones, wireless access points, and advanced pan/tilt/zoom security cameras, as well as any 15.4 W IEEE 802.3af-compliant end device; mitigates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. Auto-PoE Power Configuration The switch automatically assigns the required power to a port for a PD device based on Link Layer Discovery Protocol (LLDP). PoE Power Allocation Support multiple methods (LLDP-MED automatic, class of PoE, or usage-based) to allocate PoE power for more efficient energy savings. Auto MDI/MDI-X Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports. Network Security TPM-Based Security Includes a Trusted Platform Module (TPM) for secure hardware- based generation and storage of cryptographic keys used for secure connection to the Instant On cloud portal. IEEE 802.1Q VLAN Support Support for up to 256 VLANs with a VLAN ID range of 2-4093. IEEE 802.1X Access Control Authentication of network users on a per port basis prior to permitting network access. Port authentication includes RADIUS assigned VLAN, dynamic VLAN creation, guest VLAN or into an unauthenticated VLAN. Automatic Denial-of-Service Protection Monitors for malicious attacks and protects the network by blocking the attacks. Packet Storm Protection Protects against unknown unicast, broadcast and multicast storms with user-defined thresholds. RADIUS The switch supports RADIUS authentication with primary and backup server configuration. Automatic VLAN Assignment - RADIUS Assigned VLANs Automatically assigns users to the appropriate VLAN based on their identity and location. RADIUS Accounting A robust set of attributes and statistics are available for collecting information from the switch. Management VLAN ID Provides secure management access to administrators in the specified VLAN. Link Flap Prevention Minimizes the network disruption by automatically detecting and disabling ports that experience link flap events. Performance and Efficiency Energy Efficient Ethernet (EEE) Compliant with IEEE 802.3az standard requirements to save energy during periods of low data activity. Auto-Port Shut Down The switch saves power by automatically shutting down power to inactive ports. Power is restored on a port upon link detection. Energy Savings Status The switch provides an estimated cumulative energy savings due to green Ethernet features being enabled. Energy-Efficient Cooling Includes variable speed fans operating only at the speed necessary to maintain operating temperature to reduce excess noise and power consumption. Fan-Less Operation Fan-less design for 8-port models, 24- and 48-port non-PoE models, making the switches ideal for office deployments. Switching Features IEEE 802.3x Flow Control Provides a flow-throttling mechanism propagated through the network to prevent packet loss at a congested node. Spanning Tree Protocol (STP) Supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP on local web). Loop Protection If the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms. BPDU Filtering Drops BPDU packets when STP is enabled globally but disabled on a specific port. Jumbo Frame Support Supports up to 9216 bytes frame size to improve the performance of large data transfers. IGMP Snooping v1/v2 Improves network performance through multicast filtering, instead of flooding traffic on all ports. Link Aggregation Groups together multiple ports up to a maximum of eight (8) ports per trunk automatically using Link Aggregation Control Protocol (LACP), or manually, to form a high-bandwidth connection to the network backbone that helps prevent traffic bottlenecks. The 8-port models support 4 trunks, 24-port models support 8 trunks, and 48-port models support 16 trunks. LLDP/LLDP-MED (Media Endpoint Discovery) Defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN for automatic configuration of network devices such as IP phones. Address Resolution Protocol (ARP) The ARP table displays all of the IP addresses that have been resolved to MAC addresses, either dynamically or through static entry configuration. Additional Features Accessed Through Local Web-Management Interface Top Event Dashboard Provides notifications for critical events and a quick access to the latest log events. Quick Start-Up and VLAN Wizard Enables automatic configuring of the initial settings such IP address, device information, and system time. VLAN wizard can be used for setting up initial VLAN IDs and port membership. Access Control Lists (ACLs) Enables network traffic filtering by creating an ACL, adds rules and matches criteria to an ACL, and applies the ACL to permit or deny on one or more interfaces or a VLAN. Supports for 50 inbound IPv4 and MAC ACLs with up to 480 ACEs. IPv6 Host Enables switches to be managed and deployed at the IPv6 network's edge. Rate Limiting Sets and enforces per-port ingress traffic limits based on percentages or packets per second. Protected Ports Ports in a port isolation group are restricted from forwarding Layer 2 traffic between ports in that group, providing data privacy and security. SCP and TFTP File Transfer Provides different mechanisms for secure file transfer through SCP (Secure Copy Protocol) or TFTP. Dual Image Support Provide independent primary and secondary software images for backup while upgrading. User Account Management Password strength checking and aging feature provides enhanced security to user account administration to the local web management interface. Additionally, user account authentication can now be done via RADIUS to access the web-interface.' Secure Sockets Layer (SSL) Encrypts all HTTP traffic, secures access to the local browser-based management of the switch. SNMPv1, v2c, and v3 Facilitates remote management with SNMP management station that discovers and monitors the switch. Remote Monitoring (RMON) Provides advanced monitoring and reporting capabilities for statistics, history, alarms and events. RMON data is retrieved from the switch through a network management platform over SNMP. Cable Diagnostic Tool Provides the mechanism to detect and report potential cabling issues, such as cable opens or cable shorts on copper links, in addition to providing distance to the fault and total length of cable. Warranty, Service and Support Aruba Instant On Limited Lifetime Support provides 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is included for the life of the product. Refer to the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Objev podobné jako HPE Networking Instant On Switch 24p Gigabit CL4 PoE 4p SFP+ 370W 1930 (JL684B)

Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 195W Switch (JL683B) I/O Ports and Slots 24 RJ-45 autosensing 10/100/1000 Class 4 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 10.42(d) x 1.73(h) in (44.25 x 26.47 x 4.39 cm)(1U height) Weight 7.69lb (3.49kg) Processor and Memory ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5 MB Packet Buffer 1.5 MB Performance 100 Mb latency < 4.7 uSec 1000 Mb latency 10000 Mb latency Throughput (Mpps) 95.23 Mpps Capacity 128 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 76 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic1 LWAd = 3.9 Bel LpAm (Bystander) = 25 dB Notes: 1Acoustics measured in 23°C semi-anechoic chamber with a loading of 100% traffic and 50% PoE on all ports. Measured in accordance with ISO 7779. Declared in accordance with ECMA-109:2010. Values presented are the Declared A-Weighted Sound Power Level (LWAd) and the mean Bystander A-Weighted Sound Pressure Level (LpAm) Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current 2.8 A/1.4 A Maximum power rating 248.7W Idle power 19.7W PoE power 195 W Class 4 PoE Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) Aruba Instant On 10G SFP+ to SFP+ 1m DAC (R9D19A) Aruba Instant On 10G SFP+ to SFP+ 3m DAC (R9D20A) Aruba Instant On 1930 Switch Series High-Performance, Smart-Managed Switches Designed with Small Businesses in Mind Whether you own a cafe, a design firm or a tech startup, a reliable and secure network plays a critical role in the success of your business. And you need a network solution that gives you peace of mind, allowing you to focus on growing your business instead of managing problems with your network. Aruba Instant On makes it easy to keep network users happy, mobile and IoT devices connected, and your network secure. The Aruba Instant On 1930 switches features advanced, smart-managed, fixed- configuration Gigabit switches designed for small businesses that are easy-to-deploy and affordable. They're made to handle today's bandwidth-heavy applications like voice and video conferencing, enabling consistent connectivity to enhance performance. Using either the Instant On mobile app or the cloud-based web portal, you can quickly set up, monitor and manage the 1930 switch series from anywhere at any time. What's more, up to 30 W PoE power delivery is available out-of-the-box for your class 4 PoE devices, like access points, surveillance cameras and VoIP phones, all easily managed from the same platform. Built-in security features protect your network from unauthorized access by allowing you to segment traffic and define access to each area of the network. And all of this is included in the price of the hardware - there are no hidden subscription or licensing fees. Key Features Smart-managed layer 2+ Ethernet switch series ready to deploy in 8-, 24-and 48-port for non-PoE and Class 4 PoE models PoE to power APs and IoT devices like IP phones, surveillance cameras and door locks Two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models to eliminate traffic bottlenecks across your network Security controls let you define access in each area of your network, keeping your business data safe Convenient mobile app and web- based GUI for set up, management and troubleshooting. Standard Features Simplicity at Its Best Plug-and-play switches that work together with Instant On APs right out of the box Mobile app to easily setup, monitor and manage your network Security You Can Count On Protect your network from unauthorized access with IEEE 802.1X and VLANs Automatic denial-of-service (DOS) monitors and protects the network against malicious attacks We've Got You Covered No extra licensing or subscription fees Industry-leading limited lifetime warranty and support. The Instant On Differentiators Easy Setup and Management The Aruba Instant On mobile app allows you to set up, manage, and monitor Instant On switches and access points directly from your phone. Within the app, you get guided step-by-step instructions to install Instant On devices to get your network up and running quickly - no technical expertise required. And cloud-based access allows you to access the network from anywhere, at any time. Non-intrusive, Aesthetic Design Aruba Instant On switches are designed to complement the sleek and clean look of the Instant On access points, and to blend discreetly into your site's environment. The 8-port models, as well as the 24- and 48-port non PoE models, are fan-less, making them ideal for quiet office deployments. High Performance with Flexible Options The series consists of four (4) Class 4 PoE switches, and three (3) non-PoE switches including 8- 24- and 48-port Gigabit Ethernet switches. The two (2) dedicated 1G SFP fiber ports on 8-port models, and four (4) dedicated 1G/10G SFP+ fiber ports on 24-/48-port models, ensure high performance and eliminate traffic bottlenecks across the network. Customizable features include basic Layer 2 features like VLANs and link aggregation, as well as advanced features such as Layer 3 IPv4 static routing, ACLs, and Spanning Tree Protocols, and IPv6 Host mode. Optimized User Experience The Aruba Instant On mobile app provides common workflows for Instant On switches and access points making it easier to configure, monitor and manage your network remotely without the need for additional hardware like cloud keys or VPN. You can also update firmware on your Instant On devices directly from the cloud whenever you want, from wherever you are. Site inventory The site inventory feature on the Instant On mobile app shows you all switches and AP's on a single screen, allowing you to quickly identify non-functioning devices and troubleshoot accordingly. Multi-Site Management The cloud-hosted web interface and mobile app make it easy to manage multiple sites, multiple networks, distributed deployments and multi-tenant deployments. Each site is logically separated and has its own configuration, statistics, guest portal, and admin read/write privileges. Built-In Security Built-in security features protect your network from external threats by blocking malware attacks and keeping unauthorized users off the network. Network traffic can be filtered and access restricted based on MAC and IP address. No Hidden Fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry leading limited lifetime warranty are also included, along with chat support for the life of the product. Management Cloud-Based Management for Entire Network The cloud-hosted web interface and mobile app make it easy to manage networks with Instant On APs and Switches. Simple Local Web GUI Management For management of individual switches, the intuitive Web GUI makes management simple, even for non-technical users. Supports up to five (5) HTTP and HTTP Secure (HTTPS) sessions. Firmware Update Provides notification of the latest firmware with the ability to schedule update at a preferred time through Instant On mobile app and cloud-based web portal. Default DHCP Client Mode Allows the switch to be directly connected to a network, enabling plug-and-play operation. In the absence of a DHCP server on the network, the switch falls back to the static address 192.168.1.1. Port Mirroring Enables traffic on a port or VLAN to be simultaneously sent to a network analyzer for monitoring. Event Logging and Alerts Provides detailed information for problem identification and resolution. Account Management Allows administrators to add, modify, delete and transfer management accounts and passwords for secure access to Instant cloud management solution. Locator LED Allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches. Schedule Configuration Global Schedule feature can be applied to time-based ACLs, port or interface shutdown, or PoE power delivery; up to 3 schedules can be configured. PoE scheduling allows user to configure a specific day/time of the week (e.g. business hours) for Instant On switches to supply power to connected devices (e.g. surveillance cameras, access points etc.). Quality of Service (QoS) Traffic Prioritization Provides time-sensitive packets (like VoIP and video) with priority over other traffic based on DSCP or IEEE 802.1p classification. IEEE 802.1p/Q VLAN Tagging Delivers data to devices based on the priority and type of traffic; supports IEEE 802.1Q. Class of Service (CoS) Sets the IEEE 802.1p/DSCP priority to queue mapping (4 queues). Supports strict priority queuing (SP) or weighted round robin (WRR) queuing. SP and WRR queuing can be configured on individual switch ports. Advanced Classifier Based QoS Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information. Access Switching SFP/SFP+ Fiber Connectivity Provides fiber connections for uplinks and other connections across longer distances than copper cabling can support. SFP ports are in addition to available copper Ethernet ports, providing a higher total number of available ports. Two (2) SFP 1G ports available on 8-port models and four (4) SFP+ 1G/10G ports on 24-/48 port models. Ethernet Alliance Certified Class 4 PoE (IEEE 802.3at) Provides up to 30 W per port, which allows support of the class 4 PoE capable devices such as video IP phones, wireless access points, and advanced pan/tilt/zoom security cameras, as well as any 15.4 W IEEE 802.3af-compliant end device; mitigates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments. Auto-PoE Power Configuration The switch automatically assigns the required power to a port for a PD device based on Link Layer Discovery Protocol (LLDP). PoE Power Allocation Support multiple methods (LLDP-MED automatic, class of PoE, or usage-based) to allocate PoE power for more efficient energy savings. Auto MDI/MDI-X Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports. Network Security TPM-Based Security Includes a Trusted Platform Module (TPM) for secure hardware- based generation and storage of cryptographic keys used for secure connection to the Instant On cloud portal. IEEE 802.1Q VLAN Support Support for up to 256 VLANs with a VLAN ID range of 2-4093. IEEE 802.1X Access Control Authentication of network users on a per port basis prior to permitting network access. Port authentication includes RADIUS assigned VLAN, dynamic VLAN creation, guest VLAN or into an unauthenticated VLAN. Automatic Denial-of-Service Protection Monitors for malicious attacks and protects the network by blocking the attacks. Packet Storm Protection Protects against unknown unicast, broadcast and multicast storms with user-defined thresholds. RADIUS The switch supports RADIUS authentication with primary and backup server configuration. Automatic VLAN Assignment - RADIUS Assigned VLANs Automatically assigns users to the appropriate VLAN based on their identity and location. RADIUS Accounting A robust set of attributes and statistics are available for collecting information from the switch. Management VLAN ID Provides secure management access to administrators in the specified VLAN. Link Flap Prevention Minimizes the network disruption by automatically detecting and disabling ports that experience link flap events. Performance and Efficiency Energy Efficient Ethernet (EEE) Compliant with IEEE 802.3az standard requirements to save energy during periods of low data activity. Auto-Port Shut Down The switch saves power by automatically shutting down power to inactive ports. Power is restored on a port upon link detection. Energy Savings Status The switch provides an estimated cumulative energy savings due to green Ethernet features being enabled. Energy-Efficient Cooling Includes variable speed fans operating only at the speed necessary to maintain operating temperature to reduce excess noise and power consumption. Fan-Less Operation Fan-less design for 8-port models, 24- and 48-port non-PoE models, making the switches ideal for office deployments. Switching Features IEEE 802.3x Flow Control Provides a flow-throttling mechanism propagated through the network to prevent packet loss at a congested node. Spanning Tree Protocol (STP) Supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP on local web). Loop Protection If the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms. BPDU Filtering Drops BPDU packets when STP is enabled globally but disabled on a specific port. Jumbo Frame Support Supports up to 9216 bytes frame size to improve the performance of large data transfers. IGMP Snooping v1/v2 Improves network performance through multicast filtering, instead of flooding traffic on all ports. Link Aggregation Groups together multiple ports up to a maximum of eight (8) ports per trunk automatically using Link Aggregation Control Protocol (LACP), or manually, to form a high-bandwidth connection to the network backbone that helps prevent traffic bottlenecks. The 8-port models support 4 trunks, 24-port models support 8 trunks, and 48-port models support 16 trunks. LLDP/LLDP-MED (Media Endpoint Discovery) Defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN for automatic configuration of network devices such as IP phones. Address Resolution Protocol (ARP) The ARP table displays all of the IP addresses that have been resolved to MAC addresses, either dynamically or through static entry configuration. Additional Features Accessed Through Local Web-Management Interface Top Event Dashboard Provides notifications for critical events and a quick access to the latest log events. Quick Start-Up and VLAN Wizard Enables automatic configuring of the initial settings such IP address, device information, and system time. VLAN wizard can be used for setting up initial VLAN IDs and port membership. Access Control Lists (ACLs) Enables network traffic filtering by creating an ACL, adds rules and matches criteria to an ACL, and applies the ACL to permit or deny on one or more interfaces or a VLAN. Supports for 50 inbound IPv4 and MAC ACLs with up to 480 ACEs. IPv6 Host Enables switches to be managed and deployed at the IPv6 network's edge. Rate Limiting Sets and enforces per-port ingress traffic limits based on percentages or packets per second. Protected Ports Ports in a port isolation group are restricted from forwarding Layer 2 traffic between ports in that group, providing data privacy and security. SCP and TFTP File Transfer Provides different mechanisms for secure file transfer through SCP (Secure Copy Protocol) or TFTP. Dual Image Support Provide independent primary and secondary software images for backup while upgrading. User Account Management Password strength checking and aging feature provides enhanced security to user account administration to the local web management interface. Additionally, user account authentication can now be done via RADIUS to access the web-interface.' Secure Sockets Layer (SSL) Encrypts all HTTP traffic, secures access to the local browser-based management of the switch. SNMPv1, v2c, and v3 Facilitates remote management with SNMP management station that discovers and monitors the switch. Remote Monitoring (RMON) Provides advanced monitoring and reporting capabilities for statistics, history, alarms and events. RMON data is retrieved from the switch through a network management platform over SNMP. Cable Diagnostic Tool Provides the mechanism to detect and report potential cabling issues, such as cable opens or cable shorts on copper links, in addition to providing distance to the fault and total length of cable. Warranty, Service and Support Aruba Instant On Limited Lifetime Support provides 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is included for the life of the product. Refer to the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office. Standards and Protocols (applies to all products in series) IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3z 1000BASE-X IEEE 802.2af PoE 1 (PoE models only) IEEE 802.3at PoE 1 (PoE models only) IEEE 802.3x Flow control IEEE 802.1Q VLANS IEEE 802.1p Priority IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.1X Port Access Authentication IEEE 802.3az Energy Efficient Ethernet IEEE 802.1D: Spanning Tree Protocol IEEE 802.1W: Rapid Spanning Tree Protocol IEEE 802.1S: Multiple Spanning Tree Protocol IEEE 802.1AB Link Layer Discovery Protocol Denial of service protection CPU DoS protection

Objev podobné jako HPE Networking Instant On Switch 24p Gigabit CL4 PoE 4p SFP+ 195W 1930 JL683B

Aruba Instant On 1930 48G Class4 PoE 4SFP/SFP+ 370W Switch Produktový kód: JL686B Porty a sloty 48 RJ-45 autosensing 10/100/1000 Class 4 PoE ports 4 SFP+ 1/10GbE ports Physické charakteristiky Dimensions: 17.42(w) x 12.7(d) x 1.73(h) in Weight: 10.12 lb (4.59 kg) Procesor ARM Cortex-A9 @ 800 MHz Paměť a Flash 512 MB SDRAM 256 MB flash Performance 100 Mb latency:

Objev podobné jako HPE Networking Instant On Switch 48p Gigabit CL4 PoE 4p SFP+ 370W 1930 (JL686B)

HPE Aruba Networking 2930F 12G PoE+ 2G/2SFP+ Switch RENEW JL693A

Objev podobné jako HPE Aruba Networking 2930F 12G PoE+ 2G/2SFP+ Switch RENEW JL693A

Aruba Instant On 1930 24G 4SFP/SFP+ Switch Aruba Instant On 1930 24G 4SFP/SFP+ Switch je vysokovýkonný, chytrě spravovaný switch navržený s ohledem na malé podniky. Snadno se implementuje a je cenově dostupný. Je navržen tak, aby zvládal dnešní náročné aplikace, jako je hlasová a video konference, a zajišťoval tak konzistentní připojení pro zlepšení výkonu. Specifikace Porty: 24 RJ-45 autosensing 10/100/1000 ports, 4 SFP+ 1/10GbE ports Rozměry: 17.42(w) x 8.72(d) x 1.73(h) in (44.25 x 22.15 x 4.39 cm) Hmotnost: 5.32 lb (2.41 kg) Procesor a paměť: ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash Výkon: Průchodnost 95.23 Mpps, kapacita 128 Gbps Prostředí: Provozní teplota 32°F to 104°F (0°C to 40°C), vlhkost 15% to 95% @ 104°F (40°C) Elektrické vlastnosti: Frekvence 50-60 Hz, napětí 100-240V, proud 0.5/0.3 A, maximální výkon 22.6 W Vlastnosti Snadná instalace a správa: Aplikace Aruba Instant On umožňuje nastavit, spravovat a monitorovat switche a přístupové body přímo z vašeho telefonu. Bezpečnost: Vstavané bezpečnostní funkce chrání vaši síť před neoprávněným přístupem. Vysoký výkon: Série se skládá ze čtyř (4) třídních 4 PoE (PoE+) switchů a tří (3) non-POE switchů včetně 8- 24- a 48-portových Gigabit Ethernet switchů. Optimalizovaný uživatelský zážitek: Aplikace Aruba Instant On poskytuje běžné postupy pro switche a přístupové body Instant On, což usnadňuje konfiguraci, monitorování a správu vaší sítě na dálku. Žádné skryté poplatky: Všechny funkce jsou zahrnuty v ceně hardwaru - nejsou zde žádné opakující se poplatky za předplatné nebo licence. Bezpečnostní funkce TPM-based security: Zahrnuje Trusted Platform Module (TPM) pro bezpečné generování a ukládání kryptografických klíčů. Automatická ochrana proti DoS: Monitoruje a chrání síť před škodlivými útoky. ARP Attack prevention: Dynamická ARP ochrana blokuje ARP vysílání od neautorizovaných hostitelů. Port security: Porty v izolační skupině portů jsou omezeny na přeposílání vrstvy 2 mezi porty v této skupině. Výkon a efektivita Energy Efficient Ethernet (EEE): Splňuje požadavky standardu IEEE 802.3az pro úsporu energie během období nízké datové aktivity. Auto-port shut down: Switch šetří energii automatickým vypnutím napájení na neaktivních portech. Energy-efficient cooling: Zahrnuje proměnné rychlosti ventilátorů, které pracují pouze na rychlosti nutné k udržení provozní teploty. Switching Features IEEE 802.3x Flow control: Poskytuje mechanismus pro regulaci toku šířený sítí, aby se zabránilo ztrátě paketů na přeplněném uzlu. Spanning Tree Protocol (STP): Podporuje standardní IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) pro rychlejší konvergenci. Jumbo frame support: Podporuje až 9216 bajtů velikosti rámců pro zlepšení výkonu při přenosu velkých dat. Záruka, servis a podpora Aruba Instant On Limited Lifetime Support poskytuje 24X7 telefonickou podporu po dobu prvních 90 dnů a podporu chatu po dobu záruky. Komunitní podpora je zahrnuta po dobu života produktu.

Objev podobné jako 20 x Aruba Instant On 1930 24G 4SFP/SFP+ Switch

Aruba Instant On 1930 24G Class4 PoE 4SFP/SFP+ 195W Switch (JL683B) I/O Ports and Slots 24 RJ-45 autosensing 10/100/1000 Class 4 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE- TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 4 SFP+ 1/10GbE ports Physical Characteristics Dimensions 17.42(w) x 10.42(d) x 1.73(h) in (44.25 x 26.47 x 4.39 cm)(1U height) Weight 7.69lb (3.49kg) Processor and Memory ARM Cortex-A9 @ 800 MHz, 512 MB SDRAM, 256 MB flash; packet buffer: 1.5 MB Packet Buffer 1.5 MB Performance 100 Mb latency < 4.7 uSec 1000 Mb latency <2.4 uSec 10000 Mb latency <1.3 uSec Throughput (Mpps) 95.23 Mpps Capacity 128 Gbps Routing table size (# of static entries) 32 MAC address table size (# of entries) 16,000 Reliability MTBF (years) 76 Environment Operating temperature 32°F to 104°F (0°C to 40°C) Operating relative humidity 15% to 95% @ 104°F (40°C) Non-operating temperature -40°F to 158°F (-40°C to 70°C) Non-operating relative humidity 15% to 95% @ 140°F (60°C) Altitude Up to 10,000ft (3.048 Km) Acoustic1 LWAd = 3.9 Bel LpAm (Bystander) = 25 dB Notes: 1Acoustics measured in 23°C semi-anechoic chamber with a loading of 100% traffic and 50% PoE on all ports. Measured in accordance with ISO 7779. Declared in accordance with ECMA-109:2010. Values presented are the Declared A-Weighted Sound Power Level (LWAd) and the mean Bystander A-Weighted Sound Pressure Level (LpAm) Electrical Characteristics Frequency 50-60 Hz AC voltage 100 - 127 / 200 - 240 VAC Current 2.8 A/1.4 A Maximum power rating 248.7W Idle power 19.7W PoE power 195 W Class 4 PoE Power supply Internal power supply Safety UL 60950-1; IEC 60950-1;EN 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics IEC 61000-3-2, EN 61000-3-2 Flicker IEC 61000-3-3, EN 61000-3-3 Device Management Aruba Instant On Cloud; Web browser; SNMP Manager Mounting Mounts in an EIAstandard 19 in. telco rack or equipment cabinet. 2-post rack kit included Supports table-top mounting Supports rackmounting Supports wall-mounting with ports facing either up or down Supports under-table mounting using the brackets provided Transceivers Aruba Instant On 1G SFP LC SX 500m OM2 MMF Transceiver (R9D16A) Aruba 1G SFP LC LX 10km SMF Transceiver (J4859D) Aruba Instant On 1G SFP RJ45 T 100m Cat5e Transceiver (R9D17A) Aruba Instant On 10G SFP+ LC SR 300m OM3 MMF Transceiver (R9D18A) Aruba 10G SFP+ LC LR 10km SMF Transceiver (J9151E) Aruba Instant On 10G SFP+ to SFP+ 1m DAC (R9D19A) Aruba Instant On 10G SFP+ to SFP+ 3m DAC (R9D20A)

Objev podobné jako 10 x HPE Networking Instant On Switch 24p Gigabit CL4 PoE 4p SFP+ 195W 1930 (JL683B)

Aruba Instant On 1960 Switch Model: Aruba Instant On 1960 8p (1G Class 4 PoE) 4p (SR1G/2.5G Class 6 PoE) 2p (10GBASE-T 2p SFP+) 480W Switch EAN: 190017628400 Popis produktu Aruba Instant On 1960 Switch je výkonný a spolehlivý switch, který přináší vysokou propustnost a pokročilé funkce pro malé a střední podniky. Vlastnosti 8 portů 1G Class 4 PoE 4 porty SR1G/2.5G Class 6 PoE 2 porty 10GBASE-T 2 porty SFP+ Výkon 480W Výhody Aruba Instant On 1960 Switch nabízí vysokou propustnost a flexibilitu, díky které je ideální pro malé a střední podniky, které potřebují rychlou a spolehlivou síť. Dodávka Switch je dodáván s napájecím kabelem a uživatelskou příručkou.

Objev podobné jako HPE Networking Instant On Switch 8p Gigabit CL4 4p SR2.5G CL6 PoE 2p 10GBT 2p SFP+ 480W 1960

Switch 48 portový, 1 Gbit, 2× SFP, QoS, VLAN, rack Switch je aktivní síťová jednotka propojující jednotlivá zařízení případně další prvky sítě. Slouží k vedení síťového provozu. Tenda TEG1050F Gigabit Switch with SFP byl navržen k umístění do racku. Tento typ dokáže zaujmout svou přepínací kapacitou 100 Gb/s a paketovou kapacitou 14,9 ks. Switch je vybaven 48 ks RJ-45 portů, které jsou poskytnuty k propojení se síťovými prvky. Celkem 2 konektory typu SFP užijete k přenosu dat skrz optická vlákna. Přepínač pracuje s technologiemi dovolující převádět data až do rychlosti 1000 Mbit/s. Využívá Dual Personality porty, které se mohou pochlubit tím, že je jejich součástí konektor RJ-45 i SFP, v jedné chvíli je možné využít jen jeden z nich. Rozměry switche byly stanoveny na 240 × 440 × 44 mm. Díky technologii QoS neboli Quality of Service není možné vytížení switche, navíc lze seřídit prioritu koncových zařízení. Integrované LAN porty podporují přenosovou rychlost...

Objev podobné jako Tenda TEG1050F Gigabit Switch with SFP (TEG1050F)

Aruba 6000 12G PoE Class4 + 2x1GbE 2x1GSFP 139W Switch R8N89AR RENEW Produktový kód: 726221 Specifikace Počet portů: 12x 10/100/1000BASE-T, 2x 1G SFP, 2x 1GbE Podpora PoE standardů: IEEE 802.3af, 802.3at Porty: 1x USB-C Console, 1x USB Type-A Host Zdroj energie: Pevný, až 139W Class 4 PoE Technické parametry Procesor: Dual Core ARM Cortex A9 @ 1016 Mhz Paměť: 4 GB DDR3, 16 GB eMMC Switchovací kapacita: 32 Gbps Průchozí kapacita: 23.8 Mpps Průměrná latence: 1 Gbps: 2.3 µSec IPv4 Host Table (ARP): 1,024 IPv6 Host Table (ND): 512 IPv4 Unicast Routes: 512 IPv6 Unicast Routes: 512 MAC Table Capacity: 8,192 Provozní podmínky Provozní teplota: 32°F to 113°F (0°C to 45°C) Vlhkost při provozu: 15% to 95% at 104°F (40°C) non-condensing Maximální provozní výška: 10000 feet (3 km) Maximální neoperační výška: 15000 feet (4.6 km) Energetické nároky Frekvence: 50 / 60 Hz Napětí: 100-127 VAC / 200-240 VAC Proud: 1.8 A / 0.9 A Spotřeba (230 VAC): idle: 16W, Max Power (w/o PoE): 21.9W, Max Power (w/ PoE): 170W Bezpečnostní a emisní normy Safety: UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368-1:2014 Emissions: VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Montáž Montuje se v EIA-standardním 19-palcovém telco racku nebo skříni (k dispozici rack-mounting kit), horizontální montáž na povrch, montáž na zeď.

Objev podobné jako HPE Aruba Networking CX 6000 12G Class4 PoE 2G/2SFP 139W Switch R8N89AR RENEW

.HP 2530-48 Switch HP RENEW.

Objev podobné jako Aruba 2530-48 HP RENEW Switch J9781AR

8-portový multi-gigabitový inteligentný riadený prepínač s 2 SFP+ Uplink 100M/1G/2.5G/5G/10G Ethernet (RJ-45) 8x 10-Gigabit SFP+ 2x.

Objev podobné jako Zyxel XS1930-12F 8-port SFP+ Smart Managed Switch, 8x SFP+, 2x 10GbE Uplink

Switch 24 portový, 1 Gbit, 2× SFP, QoS, VLAN, rack Přepínač známý jako switch je aktivní síťový komponent, který propojuje jednotlivá zařízení popřípadě jiné prvky sítě. Slouží ke správě síťového provozu. Tenda TEG1024F Gigabit Fanless Rackmount Switch + SFP je určen k umístění do racku. Tento model upoutá přepínací kapacitou 48 Gb/s a paketovou kapacitou 35600000 ks. Switch je opatřen 24 ks RJ-45 portů, které jsou určeny k propojení se síťovými prvky. Celkem 2 konektory typu SFP užijete k přenosu dat přes optická vlákna. Přepínač pracuje s technologiemi umožňující šířit data až do rychlosti 1000 Mbit/s. Využívá Dual Personality porty, které jsou mimořádné tím, že poskytují konektor RJ-45 i SFP, v konkrétním okamžiku je k využití jen jeden z nich. Rozměry switche jsou 180 × 440 × 44 mm. Díky technologii QoS alias Quality of Service je zabráněno vytížení switche, je také možné nastavit přednost koncových zařízení. Integrované LAN porty podporují přenosovou...

Objev podobné jako Tenda TEG1024F Gigabit Fanless Rackmount Switch + SFP (TEG1024F)

HARDWAROVÉ VLASTNOSTI Rozhraní • 20× Gigabit SFP sloty • 4× Gigabit Combo SFP/RJ45 porty • 4× 10G SFP+ sloty • 1× RJ45 Console Port • 1× Micro-USB Console Port Počet ventilátorů 1 ventilátor Fyzický bezpečnostní zámek ? Zdroj napájení • Duální redundantní napájecí zdroje • 100-240 V AC~50/60 Hz Rozměry (Š x H x V) 17,3×8,7×1,7 palce (440×220×44 mm) Montáž Montáž do racku Maximální spotřeba energie 35.7 W (110 V/60 Hz) Maximální odvod tepla 121.81 BTU/hr (110 V/60 Hz) VÝKON Přepínací kapacita 128 Gbps Rychlost přeposílání paketů 95,23 Mpps Tabulka MAC adres 16 K Paměť vyrovnávací paměti paketů 12 Mbit Jumbo rám 9 kB SOFTWAROVÉ FUNKCE Kvalita služeb • 8 prioritních front • Priorita 802.1p CoS/DSCP • Plánování fronty: SP (Strict Priority), WRR (Weighted Round Robin), SP+WRR • Řízení šířky pásma: Omezení hodnocení podle portu/toku • Hladší výkon • Akce pro toky: QoS poznámka (802.1P poznámka, DSCP poznámka) Funkce L2 a L2+ • 128 rozhraní IP: Podpora rozhraní IPv4/IPv6 • Statické směrování: 48 statických směrování IPv4/IPv6 • Statické ARP: 128 statických záznamů • 512 záznamů ARP • Proxy ARP • Bezplatná ARP • Server DHCP • Relé DHCP: Přenos rozhraní DHCP, VLAN DHCP Relay • DHCP L2 Relay • Link Aggregation • Spanning Tree Protocol • Loopback Detection • 802.3x Flow Control • Mirroring L2 Multicast • Podporuje 1000 (IPv4, IPv6) skupin IGMP • IGMP Snooping • IGMP Authentication • Multicast VLAN Registration (MVR) • MLD Snooping • Multicast Filtering: 256 profilů a 16 záznamů na profil Pokročilé funkce • Automatické zjišťování zařízení † • Dávková konfigurace † • Dávková aktualizace firmwaru † • Inteligentní monitorování sítě † • Varování nad abnormálními událostmi † • Sjednocená konfigurace † • Plán restartu † Funkce ISP *: • L2PT (Layer 2 Protocol Tunecting) • Protokol Device Link DLDP) • Vložení PPPoE ID • ERPS • 802.3ah Ethernet Link OAM • DDM • sFlow VLAN • VLAN Group: Max 4K VLAN Groups • 802.1q Tagged VLAN • MAC VLAN: 30 Entries • Protocol VLAN: Protocol Template 16, Protocol VLAN 16 • Private VLAN • GVRP • VLAN VPN: VLAN Mapping, VLAN Replace • Voice VLAN Seznam řízení přístupu • Time-based ACL • MAC ACL: Source MAC, Destination MAC, VLAN ID, User Priority, Ether Type • IP ACL: Source IP, Destination IP, Fragment, IP Protocol, TCP Flag, TCP/UDP Port, DSCP/IP TOS • Kombinovaný ACL • ACL s obsahem paketů • IPv6 ACL • Zásady: zrcadlení, přesměrování, omezení rychlosti, QoS Poznámka • ACL platí pro port/VLAN Bezpečnostní • Vazba IP-MAC-Port - 512 záznamů - DHCP Snooping - ARP Inspection - IPv4 Source Guard • IPv6-MAC-Port Binding - 512 Entries - DHCPv6 Snooping - ND Detection - ND Snooping - IPv6 Source Guard • DoS Defend • Static/Dy Zabezpečení portu: Až 64 MAC adres na port • Broadcast/Multicast/Unicast Storm Control: kb/s/režim řízení poměru • 802.1X – Základní autentizace portů – Autentizace na základě MAC – Přiřazení VLAN – MAB – VLAN pro hosty – Radiusová autentizace a podpora odpovědnosti • AAA (včetně TACACS+) • Izolace portů • Zabezpečená správa webu prostřednictvím HTTPS s SSLv3/TLS 1.2 • Správa zabezpečeného rozhraní příkazového řádku (CLI) s SSHv1/SSHv2 • Řízení přístupu na základě IP/Port/MAC IPv6 • IPv6 Dual IPv4/IPv6 • Multicast Listener Discovery (MLD) Snooping • IPv6 ACL • IPv6 Interface • Statické IPv6 směrování • IPv6 sousední zjišťování (ND) • Zjištění maximální přenosové jednotky (MTU) • Internet Control Message Protocol (ICMP) verze 6 • TCPv6/UDPv6 • Aplikace IPv6: Klient DHCPv6, Ping6, Tracert6, Telnet (v6), IPv6 SNMP, IPv6 SSH, IPv6 SSL, Http/Https, IPv6 TFTP MIB • MIB II (RFC1213) • Rozhraní MIB (RFC2233) • Rozhraní Ethernet MIB (RFC1643) • Most MIB (RFC1493) • P/Q-Bridge MIB (RFC2674) • RMON MIB (RFC2819) • RMON2 MIB (RFC2021) • Radius Accounting Client MIB (RFC2620) • Radius Authentication Client MIB (RFC2618) • Remote Ping, Traceroute MIB (RFC2925) • Podpora TP-Link private MIB ŘÍZENÍ Aplikace Omada Ano. Vyžaduje použití Omada Hardware Controller, Omada Cloud-Based Controller nebo Omada Software Controller. Centralizované řízení • Omada Cloud-Based Controller • Omada Hardware Controller • Omada Software Controller Cloud Access Ano. Vyžaduje použití Omada Hardware Controller, Omada Cloud-Based Controller nebo Omada Software Controller. Zero-Touch Provisioning Ano. Vyžaduje použití Omada Cloud-Based Controller. Funkce správy • Webové GUI • Rozhraní příkazového řádku (CLI) přes port konzoly, telnet • SNMP v1/v2c/v3: Trap/Inform, RMON (1,2,3,9 skupin) • Šablona SDM • Klient DHCP/BOOTP • 802.1ab LLDP/LLDP-MED • Automatická instalace DHCP • Duální obraz, duální konfigurace • Monitorování CPU • Diagnostika kabelů • EEE • Obnova hesla • SNTP • Systémový protokol OSTATNÍ Osvědčení CE, FCC, RoHS obsah balení • Spínač SG3428XF • Napájecí kabel • Průvodce rychlou instalací • Sada pro montáž do racku • Gumové nožičky Požadavky na systém Microsoft® Windows® 98SE, NT, 2000, XP, Vista™ nebo Windows 7/8/10/11, MAC® OS, NetWare®, UNIX® nebo Linux. životní prostředí • Provozní teplota: 0–45 ? (32–113 ?); • Skladovací teplota: -40–70 ? (-40–158 ?) • Provozní vlhkost: 10–90 % RH nekondenzující • Skladovací vlhkost: 5–90 % RH nekondenzující

Objev podobné jako TP-Link SG3428XF Omada 24-Port SFP L2+ Managed Switch with 4 10GE SFP+ Slots

Zyxel GS2220-28HP 28-port L2 Managed Gigabit PoE Switch EAN: 760559126766 Popis produktu Zyxel GS2220-28HP je pokročilý L2 Managed Gigabit PoE Switch s 28 porty. Tento switch je ideální pro VoIP, videokonferencie a internetovou televizi, díky svým vyspělým funkcím pro řízení provozu. Pokročilé funkce Switch GS2220-28HP nabízí širokou škálu funkcí 2. vrstvy, které zlepšují výkon hotelových, podnikových a kampusových sítí. L2 multicast IGMP Snooping Multicast VLAN Registration (MVR) Tyto funkce umožňují efektivnější řízení konvergovaného provozu. Technické specifikace 24x gigabit RJ45 4x gigabit RJ45/SFP PoE 375 W Shrnutí Zyxel GS2220-28HP je ideální pro všechny, kteří hledají vysoký výkon a pokročilé funkce pro řízení provozu. Tento switch je navržen tak, aby zvládl náročné podnikové aplikace a poskytoval stabilní a spolehlivé připojení.

Objev podobné jako Zyxel GS2220-28HP 28-port L2 Managed Gigabit PoE Switch, 24x gigabit RJ45, 4x gigabit RJ45/SFP, PoE 375 W

Aruba Instant On 1430 8G Switch EAN: 190017601571 Specifikace portů a slotů 8 RJ-45 autosensing 10/100/1000 portů. Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only Fyzické charakteristiky Velikosti: 138(d) x 157(w) x 37(h) mm Hmotnost: 1.30 lb (0.59 kg) Procesor a paměť 128Kb EEPROM Velikost paketového bufferu: 2.0 Mb Latence a průchodnost Latence 100 Mb: Provozní a skladovací podmínky Provozní teplota: 32°F to 104°F (0°C to 40°C) Provozní vlhkost: 15% to 95% @ 104°F (40°C) non-condensing Skladovací teplota: -40°F to 158°F (-40°C to 70°C) up to 15000 ft Skladovací vlhkost: 15% to 90% @ 149°F (65°C) non-condensing Akustika a napájení Bez ventilátoru Frekvence: 50Hz/60Hz Napětí: 100-240VAC Proud: 0.3A (12VDC - 1A) Maximální výkon: 12W Idle výkon: 1.7W Bezpečnostní normy Plně v souladu s normami EN/IEC 60950- 1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, EN/IEC 62368-1, 2nd. & 3rd. Ed., UL 62368-1, 3rd. Ed., CAN/CSA C22.2 No. 62368-1, 3rd. Ed., EN/IEC 60825- 1:2014 Class 1. Emission Atenduje normy EN 55032:2015/ CISPR 32, Class B, FCC CFR 47 Part 15: 2018, Class B, ICES-003, Class B, VCCI-32, Class B, CNS 13438, Class B, KS C 9832, Class B, AS/NZS CISPR 32, Class B. Imunita Atenduje normy BS/EN 55035, CISPR 35, KS C 9835, EN 55035, CISPR 35, EN/IEC 61000-4-2, EN/IEC 61000-4-3, EN/IEC 61000-4-4, EN/IEC 61000-4-5, EN/IEC 61000-4-6, EN/IEC 61000-4-8, EN/IEC 61000-4-11, EN/IEC 61000-3-2, EN /IEC 61000-3-3. Správa zařízení Nespravované Montáž Podporuje montáž na stůl, na zeď s porty směřujícími nahoru nebo dolů pomocí montážních otvorů na základně. Podporuje montáž pod stůl pomocí montážních otvorů na základně.

Objev podobné jako HPE Networking Instant On Switch 8p Gigabit 1430 (R8R45A)

Aruba 6100 24G 4SFP+ Switch (JL678A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting Standards And Protocols (Applies to all products in series) RFC 1591 DNS (client) SSHv1/SSHv2 Secure Shell IEEE 802.1D MAC Bridges IEEE 802.1p Priority IEEE 802.1Q VLANs IEEE 802.1s Multiple Spanning Trees IEEE 802.1w Rapid Reconfiguration of Spanning Tree IEEE 802.3 Type 10BASE-T IEEE 802.3ab 1000BASE-T IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.3at Power over Ethernet IEEE 802.3az Energy Efficient Ethernet IEEE 802.3x Flow Control RFC 768 UDP RFC 783 TFTP Protocol (revision 2) RFC 792 ICMP RFC 793 TCP RFC 826 ARP RFC 1350 TFTP Protocol (revision 2) RFC 2131 DHCP client RFC 4330 Simple Network Time Protocol (SNTP) v4 RFC 951 BOOTP (VLAN 1 Only) RFC 1542 BOOTP Extensions (VLAN 1 only) IGMPv2/IGMPv3 IGMP/MLD Snooping RFC 1981 IPv6 Path MTU Discovery RFC 2460 IPv6 Specification RFC 2925 Remote Operations MIB (Ping only) RFC 3315 DHCPv6 (client only) RFC 3513 IPv6 Addressing Architecture RFC 3596 DNS Extension for IPv6 RFC 3176 sFlow RFC 4022 MIB for TCP RFC 4113 MIB for UDP (Partially) RFC 4251 SSHv6 Architecture RFC 4252 SSHv6 Authentication RFC 4253 SSHv6 Transport Layer RFC 4254 SSHv6 Connection RFC 4293 MIB for IP RFC 4419 Key Exchange for SSH RFC 4443 ICMPv6 RFC 4861 IPv6 Neighbor Discovery RFC 4862 IPv6 Stateless Address Auto-configuration RFC 1213 MIB RFC 1493 Bridge MIB RFC 2674 802.1p and IEEE 802.1Q Bridge MIB (Partial support. MIB objects supported: ieee8021BridgeBasePort, ieee8021BridgeBasePort, ieee8021BridgePortMrpJoinTime, ieee8021BridgePortMrpLeaveTime, ieee8021BridgePortMrpLeaveAllTime) RFC 2737 Entity MIB RFC 2863 The Interfaces Group MIB IEEE 802.1AB Link Layer Discovery Protocol (LLDP) RFC 1098 A Simple Network Management Protocol (SNMP) ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED) SNMPv1/v2c/v3 RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events) RFC 1098 A Simple Network Management Protocol (SNMP) RFC 2474 DiffServ precedence, with 2/4/8 queues per port RFC 2475 DiffServ Architecture RFC 2597 DiffServ Assured Forwarding (AF) RFC 2598 DiffServ Expedited Forwarding (EF) IEEE 802.1X Port Based Network Access Control RFC 1492 TACACS+ RFC 2138 RADIUS Authentication RFC 2866 RADIUS Accounting Secure Sockets Layer (SSL)

Objev podobné jako Aruba 6100 24G 4SFP+ Switch.

Aruba 6000 24x ports 10/100/1000BASE-T Ports 4SFP Switch. Aruba 6000 24G 4SFP Switch Model Aruba 6000 24G 4SFP Switch (R8N88A) Description 24x ports 10/100/1000BASE-T Ports 4x 1G SFP ports 1x USB-C Console Port 1x USB Type-A Host port Power supplies Fixed power supply Fans Fixed fans Dimensions (H) 4.39 cm (W) 44.2 cm (D) 20.12 cm (1.73" x 17.4" x 7.92") Configuration Weight 2.62 kg (5.78 lbs) CPU Dual Core ARM Cortex A9 @ 1016 Mhz Memory and Flash 4 GB DDR3 16 GB eMMC Packet Buffer 12.38MB (4.5MB Ingress/7.875MB Egress) Model Switching Capacity 56 Gbps Model Throughput Capacity 41.6 Mpps Average Latency (LIFO-64-bytes packets) 1 Gbps: 1.5 µSec Switched Virtual Interfaces (dual stack) 16 IPv4 Host Table (ARP) 1,024 IPv6 Host Table (ND) 512 IPv4 Unicast Routes 512 IPv6 Unicast Routes 512 MAC Table Capacity 8,192 IGMP Groups 512 MLD Groups 512 IPv4/IPv6/MAC ACL Entries (ingress) 256 / 128 / 256 Environment Operating Temperature 32°F to 113°F (0°C to 45°C) up to 5000 ft (1.5 km) derate -1°C for every 1000 ft (305 m) from 5000 ft (1.5 km) to 10000 ft (3.0 km) Operating Relative Humidity 15% to 95% at 104°F (40°C) non-condensing Non-Operating -40°F to 158°F (-40°C to 70°C) up to 15000 ft (4.6 km) Non-Operating Storage Relative Humidity 15% to 90% @ 149°F (65°C) non-condensing Max Operating Altitude 10000 feet (3 km) Max Max Non-Operating Altitude 15000 feet (4.6 km) Max Acoustic Sound Power, LWAd = 3.9 Bel Sound Pressure, LpAm (Bystander) = 20.9 dB Primary Airflow Side-to-side Aruba 6000 24G 4SFP Switch (R8N88A) Electrical Characteristics Frequency 50 / 60 Hz AC Voltage 100-127 VAC / 200-240 VAC Current 0.6 A / 0.4 A Power Consumption (230 VAC) Idle: 15.4W Max Power (w/o PoE): 33W Safety UL 60950-1; IEC 60950-1; EN 60950-1; CAN/ CSA-C22.2 No. 60950-1; EN 60825-1 UL 62368-1 Ed. 2; IEC 62368-1 Ed. 2; EN 62368- 1:2014 Emissions VCCI-CISPR 32, Class A; CNS 13438; ICES-003 Issue 6 Class A; FCC CFR 47 Part 15, Class A; EN 55032: 2015 +AC:2016 / CISPR-32, Class A Lasers EN 60825-1:2007 / IEC 60825- 1:2007 Class 1 Class 1 Laser Products / Laser Klasse 1 (Applicable for accessories - Optical Transceivers only) Immunity Generic CISPR 24 / CISPR 35 EN EN 55024:2010 / EN 55035:2017 ESD IEC 61000-4-2 Radiated IEC 61000-4-3 EFT/Burst IEC 61000-4-4 Surge IEC 61000-4-5 Conducted IEC 61000-4-6 Power frequency magnetic field IEC 61000-4-8 Voltage dips and interruptions IEC 61000-4-11 Harmonics EN 61000-3-2, IEC 61000-3-2 Flicker EN 61000-3-3, IEC 61000-3-3 Mounting and Enclosure Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting

Objev podobné jako Aruba 6000 24G 4SFP Switch.

Teplovzdušný ventilátor - do bytu, do domu, na chatu, do garáže a do dílny, na podlahu, topný výkon 2000 W, 4 nastavitelné úrovně vytápění, hlučnost 56 dB(A), pojistka proti přehřátí, termostat, ventilátor a regulace teploty, rozměry 32 × 20 × 26 cm (V׊×H), bílá barva Chcete jednoduše a pohodlně vytápět interiér? Teplovzdušný ventilátor TRISTAR to hravě zařídí. K nezaplacení je jeho úctyhodný výkon, který dosahuje 2000 W. Budete moci nastavit 4 stupně výkonu, budete si tak moci zvolit teplotu kterou budete chtít. Teplovzdušný ventilátor TRISTAR budete moci díky jeho rozměrům snadno přenášet. Hlučnost přístroje dosahuje jen 56 dB(A). Díky vestavěnému termostatu můžete nejen udržovat vámi zvolenou teplotu v místnosti, ale také vám ušetří provozní náklady. Vestavěná světelná signalizace vám nabídne dokonalý přehled o stavu teplovzdušného ventilátoru TRISTAR. Speciální pojistka zabrání přehřátí. Zásadní přednosti teplovzdušného ventilátoru TRISTAR KA-5140 2v1...

Objev podobné jako TRISTAR KA-5140 2v1 (TRISTAR KA-5140)

Switch 26 portový, 1 Gbit, 1× SFP, QoS, PoE, VLAN, rack Switch je funkční síťové zařízení propojující zařízení popřípadě jiné prvky sítě. Je dělaný ke správě síťového provozu. Tenda TEF1126P-24-410W PoE Rackmount Switch 135W + SFP byl navržen k instalaci do rozvaděče. Switch je opatřen 26 ks RJ-45 portů, které jsou určeny k propojení se síťovými prvky. Jeden konektor typu SFP užijete k přenosu dat skrz optická vlákna. Switch disponuje technologiemi dovolující převádět data až do rychlosti 1000 Mbit/s. Pracuje s Dual Personality porty, jejichž mimořádnost spočívá v tom, že poskytují konektor RJ-45 i SFP, v konkrétní chvíli se dá použít jen jeden z nich. Rozměry přepínače jsou 284 × 440 × 44 mm. Díky technologii QoS alias Quality of Service se předchází přetížení switche, navíc lze seřídit přednost koncových zařízení. Zařízení Tenda také disponuje technologií PoE, jejíž zásluhou lze napájet i přivádět signál ke koncovým zařízením jen pomocí jediného LAN kabelu....

Objev podobné jako Tenda TEF1126P-24-410W PoE Rackmount Switch 135W + SFP (TEF1126P-24-410W)

Switch 24 portový, 1 Gbit, 2× SFP, PoE, desktop Switch CUDY Získejte až 24 portů, které vám umožní využívat PoE napájení (vyhovuje standardu IEEE 802.3af / 802.3at). Budete moci ve vašem okolí provozovat například přístupový bod, VoIP telefony, tiskárny nebo IP kamery. Switch CUDY umožňuje až 30W napájení na každém portu, přičemž celkový napájecí výkon na všech portech nesmí přesáhnout 300 W. Switch CUDY s perfektním odvětráváním Switch je vyroben z kvalitního...

Objev podobné jako CUDY 24-Port Gigabit PoE+ Switch with 2 SFP ports 300W (GS1028PS2)

Hra na konzoli - Nintendo Switch, krabicová verze, žánr: akční a závodní, - Nasedněte, připoutejte se a užijte si ryzí adrenalinové vzrušení ze závodní sekvence z filmu Star Wars: Epizoda I ve hře Star Wars: Episode I Racer. Ve Star Wars Republic Commando jste velitel elitní čety komandos z Republiky. Vaším úkolem je infiltrovat, dominovat a nakonec zničit nepřítele. Dvě hry v jednom baleníZískejte dvě klasické hry Star Wars s kombinací Star Wars Racer a Commando, která obsahuje Star Wars: Episode I Racer a Star Wars Republic Commando. Bavte se závoděním ve Star Wars Racer and Commando Combo PS4Nasedněte, připoutejte se a zažijte čisté adrenalinové vzrušení v podobě závodní sekvence „Podracing“ ze Star Wars: Epizoda I Skrytá hrozba ve hře Star Wars: I Racer. Zničte všechny nepřáteleVe hře Star Wars...

Objev podobné jako Star Wars Racer and Commando Combo - Nintendo Switch (9120080076908)